solid ,functional, easy on the eyes... I say success bro, well done
@Grazing-M-Acres
Жыл бұрын
Thank you!
@beamfarms
2 жыл бұрын
Great job man! Looking forward to everything else you end up creating!
@Grazing-M-Acres
2 жыл бұрын
Thanks!
@ManuelCantu-o3e
3 ай бұрын
Great idea fella nice wood work gonna build me two
@billwinslow9529
Жыл бұрын
Looks good. This took more than one sheet of plywood, correct?
@Grazing-M-Acres
Жыл бұрын
Thanks, it took just another small piece. If you down sized it just a little it would fit on one
@gasteele5559
Жыл бұрын
Excellent pig feeder! Would you happen to have the drawings for it that you could share?
@Grazing-M-Acres
Жыл бұрын
Thank you! So I don't have a drawing for it, I just sketched it out on the plywood. Rough dimensions are 24 inches wide about 18" deep at the feed lid, 12" deep at the upper section, and about 48' tall.
@nathano7942
9 ай бұрын
Great video. What kind of flashing did you find that was paintable?
@Grazing-M-Acres
9 ай бұрын
It's rubber window/door flashing, I don't know what brand it was.
@nathano7942
9 ай бұрын
Thank you
@kimberlyfaucett8579
7 ай бұрын
Did you just glue the bottom on?
@nathano7942
7 ай бұрын
I ended up just getting an old inner tube and cutting it to fit. Then I used contact cement to glue it on.
@Grazing-M-Acres
7 ай бұрын
@kimberlyfaucett8579 I used wood glue to help seal the seam but then screwed it together
@donhing9709
8 ай бұрын
This is very good
@Grazing-M-Acres
8 ай бұрын
Thank you! Glad I could help!
@zeldamurray6672
2 жыл бұрын
Great job
@Grazing-M-Acres
2 жыл бұрын
Thank you
@ernestmcguire6515
2 жыл бұрын
What are the measurements
@Grazing-M-Acres
2 жыл бұрын
It is 24 inches wide, 4 feet tall.
@danlosis7006
2 жыл бұрын
@@Grazing-M-Acres what are the dimensions of the trough?
@Grazing-M-Acres
2 жыл бұрын
Ernest Mcguire 24 inches wide 12 inches deep and 6 inches tall
@pasttime8450
Жыл бұрын
Looks great brother
@Grazing-M-Acres
Жыл бұрын
Thank you!!
@michaelbuckner5374
2 жыл бұрын
Good job cousin
@Grazing-M-Acres
2 жыл бұрын
Thank you!
@traviswelch7350
3 ай бұрын
What angels?
@Grazing-M-Acres
3 ай бұрын
Unfortunately I didn't draw any plans for this. I really just sketed it out on the board untill I got the pieces to fit.
@rickw7903
Жыл бұрын
Can you show it in action?
@Grazing-M-Acres
Жыл бұрын
Yes if you go to my page @grazingmacres we have videos of them using it.
@Accounting-yk2cp
6 ай бұрын
how has this held up to 2 years of use?
@Grazing-M-Acres
6 ай бұрын
I replaced the feeding lid just cause it started looking bad, they would chew and scratch on the corners. Thats all that ive done to it so far. if I were to wash it, it would look brand new.
@Accounting-yk2cp
6 ай бұрын
@@Grazing-M-Acres amazing! thank you for the reply. great channel too btw!
@lisabobbystamey7953
2 жыл бұрын
Are they raking the feed out on the ground?
@Grazing-M-Acres
2 жыл бұрын
Sometimes they will rake a little out when they are both eating at the same time. I would say only about 1% - 2% gets wasted. And the feed I'm feeding is real fine almost like a powder.
@lisabobbystamey7953
2 жыл бұрын
@@Grazing-M-Acres I got one similar to that I didn't make it I bought it it was one of those Dent sales couldn't pass it up I'm going to have to put some kind of adjustment in there they just waste way too much feed my feeds of powder too it might be because I have four eating out of one feeder
@Grazing-M-Acres
2 жыл бұрын
@@lisabobbystamey7953 I have a board that I adjust that regulates how much fall into the trough so that might be helping g a little too.
@rogerzay373
2 жыл бұрын
What was the material used for water proofing?
@Grazing-M-Acres
2 жыл бұрын
It a rubber window flashing used for new construction on houses, it has a sticky tar back so when it heats up it stickto whatever you put it on. You can find it at hardware stors or big box stores near the roofing supply, I forget the name brand of it but they make a bunch of didn't kinds.
Пікірлер: 43