Thank you for revealing the wheels in the thumbnail and within the first 30 seconds of the video and not dragging it out 15 minutes like other automotive KZitemrs. 🙄 Great choice. They look really good!
@MrGomjabber
4 жыл бұрын
pretty cool, would love to have one of these to bomb around in at the cabin up north where there isn't a lot of traffic.
@flat4forlife588
4 жыл бұрын
You can never go wrong with bronze, nice choice, I approve! Looks great at the end of the video!
@rogermorits5415
4 жыл бұрын
badass wheels and great price
@willmoua1
4 жыл бұрын
Too bad they discontinued the ssr type c! That was my favorite wheel I had back in the day! Currently looking for a set for my civic
@timbrown9731
4 жыл бұрын
I’ve always liked those rims over the years I remember just a few years ago when a 17 inch rim and a 16 inch rim was pretty big, on my 2013 legacy 3.6 R I didn’t really like the OEM rims that came with the car until I realized when I pulled them down to check the brakes and I was curious to see who manufactured these rims they were made by Enkei,after I realize that I decided to keep the OEM plus why go to a lower profile the roads are pretty beat up out here in California.
@ayske1
3 жыл бұрын
I actually feel 18s are pretty standard even looked good on a Mazda 3 2012 model. I actually feel any smaller on a modern Japanese car it looks small assuming a small medium hatch and bigger...
@802Garage
4 жыл бұрын
90s Subarus are usually 58-72 ft lbs (65 +/-7), I probably would go with that given it's a tiny vehicle and alloy wheels. Not that the higher torque will hurt anything, since they all basically use the same studs.
@802Garage
4 жыл бұрын
Oh and they look awesome, BTW. I love closed end lug nuts for rust prevention, but I know you don't really need to worry about that.
@MrSubaru1387
4 жыл бұрын
Just looked back through the service manuals. Yup, 88+/-10 Nm. Not sure where I got 120Nm from. Oh well. Been torquing them to 120Nm for years.
@802Garage
4 жыл бұрын
@@MrSubaru1387 I believe 120Nm is the spec for any 4th gen+ Legacy/Outback. Strangely I think it is 106Nm? For the 2nd gen Impreza/Forester and on. Not sure about the later gens like 2010+ and not 100% on the year changes.
@rodneybailey3554
4 жыл бұрын
I think that you have already answered my question about checking the tension on the wheels as I didn't see you tighten the right front wheel at all. Great looking wheels though!
@01FozzyS
4 жыл бұрын
Nice Up Garage score. I have a set of SSR Comps on my SF Forester and love them.
@lp2733
4 жыл бұрын
Wheels look good👍
@MrSubaru1387
4 жыл бұрын
Thanks!
@SubieSpecs
4 жыл бұрын
Bro, digityres in the warm rain! Those are snow tyres, I have em for my winter setup, and take em off when things go 10deg above freezing, little wonder you were having a hard time in the wet over there in the middle of summer!!! Looks sick on the SSR's bro!
@MrSubaru1387
4 жыл бұрын
Thanks!
@bierbrauer11
4 жыл бұрын
I ran SSR Competitons on my Miata, fantastic rims.
@dave11686
4 жыл бұрын
Very cool, I wouldn’t mind picking one of these up myself
@bigharrybikerbear663
4 жыл бұрын
Can you please recommend a code reader and/or software for DIY servicing US Subarus and Toyotas? Great vid! Excited to see what you do with the Sambar!
@chriscas-ToolAficionado
4 жыл бұрын
Those SSR's are bling! Looks a ton better.
@MrSubaru1387
4 жыл бұрын
Thanks! 👍🏻
@koffero7440
4 жыл бұрын
Nice looking rims , I’m running a set of aftermarket 14”JDM wheels on my Subaru Sambar Dias II Van . I also running the same size federal tires . I like them ,rides very smooth on all road surfaces , balanced with minimal weight but the understeer when raining is something you need to be ready for on sharper turns at a modest speed Think it has a bunch to do with the rear engine / forward style cab design . Can’t wait to see what’s you have next on the maintenance list
@dougnashz
Жыл бұрын
What year is your DIAS ? I just bought a 96 coming direct from Japan
@koffero7440
Жыл бұрын
@@dougnashz 92 ,94 97 and a 98
@94Greenbean
2 жыл бұрын
Great deal man! Holy crap I remember when SSR was the bomb man! Only TireRack had em for a few years too, Heck still SO OLD SKEWL KOOL bro! What a score man! I’d rock them in a heartbeat!
@michealrobinson
4 жыл бұрын
Definitely looks a lot better!
@MrSubaru1387
4 жыл бұрын
Thanks!
@dkyoungson151
4 жыл бұрын
These are some classic JDM wheels.
@joshuas10
4 жыл бұрын
Looks great! Very cool truck’ish vehicle
@27degrees
4 жыл бұрын
I think the original Dunlop DSV-01 tyres are Q rated so good for 99mph/160km/h
@MrSubaru1387
4 жыл бұрын
Ah. More speed than the Sambar will ever see. 😂
@hiphopman72
4 жыл бұрын
Sick wheels
@MrSubaru1387
4 жыл бұрын
Thanks!
@emilyturnbough1754
4 жыл бұрын
The wheels look great! 👍🏻
@MrSubaru1387
4 жыл бұрын
Thanks!
@larryborkstrom3580
4 жыл бұрын
Wheels look nice
@MrSubaru1387
4 жыл бұрын
Thanks!
@Kamelo2001
3 жыл бұрын
Love those SSR
@MrSubaru1387
3 жыл бұрын
Thanks!
@jonzaremba
4 жыл бұрын
Great improvement
@Bricketts
Жыл бұрын
I understand that I'm late to the party, but those bad boys look good!
@markharveyii4573
7 ай бұрын
So for a 93 Sambar truck.... If you needed to add hub spacers or adapters, say for a 16x7 rim with a 185/50/ 16 tire. which do fit snug they just need about 1in of space away from the front shock. The trucks hub bore is 59.1mm. my question is what size hub bore would i need the 4x100 1 inch hub spacer to be? Thanks for any help. Love the Vids. Basically walked me through replacing all of my Sambar's seals and gaskets!
@cpF01
3 жыл бұрын
Yeah. Those look great. I would love to know what you experienced for gain of highway speed from original.
@ayske1
4 жыл бұрын
super neat! Looks fab !
@MrSubaru1387
4 жыл бұрын
Thanks!
@ayske1
3 жыл бұрын
I got myself some enkei rs05rr on my legacy GT. Unsure if your channel had any influence lol
@timbrown9731
4 жыл бұрын
I think they look good Robert!
@MrSubaru1387
4 жыл бұрын
Thanks!
@adamlopez3238
3 жыл бұрын
So what are the dimensions from wheel hub to wheel hub of the rear wheels, and from the center of the rear wheel hub the the back of the truck bed...?? Thank you for your awesome channel
@jp2246
4 жыл бұрын
Nice wheels 👍
@joemikey278
4 жыл бұрын
Are these wheels forged? Just wondering, have you ever had a regular cast wheel bend or break hitting a pothole or obstruction? I would love to get a set of forged wheels on my 09 Subaru outback! Especially up here in the Northeast!
@DrewMiller4_18_5_23
4 жыл бұрын
At 2:20 he says it is forged.
@joemikey278
4 жыл бұрын
Drew Miller thanks, missed that.....
@ayske1
4 жыл бұрын
Next ep, viewers thoughts "What engine should I put in it, EJ255 or EZ36 forced induction? Most commented will be engine of choice"... :P
@kdrapertrucker
2 жыл бұрын
3.5 liter Ecoboost 😁
@thomaspotemciano
4 жыл бұрын
600 shipped? I live in the east coast and they quoted like 200+ extra for shipping on their shipping calculator
@MrSubaru1387
4 жыл бұрын
I believe just looked back at the ticket. Wheels were $650. Shipping was $150.
@thomaspotemciano
4 жыл бұрын
@@MrSubaru1387 thanks for the clarification! Yeah expecting it to be around that amount.I wa looking to order from them after you posted the pic of these a while back.
@THEDRAGONBOOSTER8
4 жыл бұрын
Very nice..
@charger19691
4 жыл бұрын
The Sambar is looking good with the new rollers. I have to ask, do you mind driving the Sambar from the right side?
@MrSubaru1387
4 жыл бұрын
Nope. Not an issue. Love driving it around. Gets loads of attention. Lol
@bierbrauer11
4 жыл бұрын
One additional comment - I thought those rims should have center caps?
@Psour
4 жыл бұрын
nice wheels......
@MrSubaru1387
4 жыл бұрын
Thanks!
@user-ps1gh9pg8z
3 жыл бұрын
spect off set ?
@NefariousTee
7 ай бұрын
Hey there! Love your videos! In looking for a wheel for my own sambar, I’ve seen a lot of 14x5.5 instead of a straight 14x5. Does this matter? Thanks!
@bricemartin9321
10 ай бұрын
I don’t see a vid where you are working on the engine for your Sambar. But maybe you could answer a question. Would a FA20 fit between the frame rails comfortably? I’m thinking about taking one mated to a BRZ six speed gearbox and rear diff. Any suggestions?
@OnkelPHMagee
4 жыл бұрын
How often do you first walk to the wrong side of the Sambar to get inside?
@MrSubaru1387
4 жыл бұрын
Haven't yet. Thankfully. Lol
@OnkelPHMagee
4 жыл бұрын
@@MrSubaru1387 Then you're a better man than I am. LOL.
@unwanted_zombie
4 жыл бұрын
I'm about to get a engine rebuild kit for my trucks engine. Any ideas? Good brands?
@tedd1091
5 ай бұрын
Can you post a link for that used JDM rims you are installing?
@sferg9582
Жыл бұрын
Does "SSR" stand for Subaru Sambar Racing?
@drumist101
2 жыл бұрын
Damn you’re really flexible dude
@jefferywise1906
Жыл бұрын
Is it the camera angle or did you miss torquing the lug at the 12:00 position on that first wheel? 😮
@itsvoodoo7050
4 жыл бұрын
Hey Mr. Subaru, quick question. I have a 04 Impreza with 124k miles with an EJ251 that had the head gaskets done at 50k miles. Recently I’ve been experiencing a misfire on only cylinder 4 on start up that last 5 seconds. I did a tune up less than 1k miles ago, new wires plugs and every filter. I did a compression test and got over 200 on that cylinder, I swapped the cables and I am just lost at what it can be. I have a whole coil pack coming in the mail and should be here on Thursday, I also have some junkyard injectors and a new spark plug, if that doesn’t fix the issues what should I look at fixing? I heard about sea foaming the engine as a possible option but I don’t know.
@MrSubaru1387
4 жыл бұрын
Do a cylinder leakage test.
@generalcaeser9176
5 ай бұрын
I want those wheels but for the life of me can not find them anywhere!
@tomlantis8016
4 жыл бұрын
Those rims make that subaru seem like its got more than 57hp
@MrSubaru1387
4 жыл бұрын
Well, it's only got 43hp. Lol supercharged version had 55. 😂
@tomlantis8016
4 жыл бұрын
@@MrSubaru1387 i bet who ever supercharged their's went you can really feel the power
@MrSubaru1387
4 жыл бұрын
Supercharger was a factory option. Like A/C. Lol
@tomlantis8016
4 жыл бұрын
@@MrSubaru1387 oh wow didnt know that thought it was a aftermarket thing. learn something new everyday thanks
@noahting2354
4 жыл бұрын
80ftlb seems like a lot. Should I be torquing my wrx lugs to that?
@MrSubaru1387
4 жыл бұрын
Most passenger cars torque to 85-100ft lbs. 120nm is Subaru standard. 120nm is like 88.5ft.lbs.
@dantheman9395
4 жыл бұрын
How did it ride? Looks great
@MrSubaru1387
4 жыл бұрын
Better handling. Little slower acceleration.
@jjacuzio
3 жыл бұрын
I have a 1995 Subaru SAMBAR van automatic trans. I live in North Carolina. Can you refer me to any good mechanic in North Carolina who can help me keep me in good running condition??? Thanks. Hey - I would even drive it to SC for good work if necessary :-)
@yamilmelendez2667
4 жыл бұрын
Are you putting a tomei or a exhaust?
@MrSubaru1387
4 жыл бұрын
Possibly..
@yamilmelendez2667
4 жыл бұрын
@@MrSubaru1387 nice 👌🏻💪🏻
@kvkv1762
4 жыл бұрын
was shipping closer to 200 or 400 usd ?
@MrSubaru1387
4 жыл бұрын
$150 USD shipping.
@kvkv1762
4 жыл бұрын
that's not bad. I was quoted over 400 usd for a set of used 17" wheels shipped to Canada so I was just curious. thanks
@carldavis7685
3 жыл бұрын
Have you measured the weights of the different wheel and tire combos?
@MrSubaru1387
3 жыл бұрын
I have not.
@unwanted_zombie
4 жыл бұрын
Wait wait WAIT. up garage has an online setup??
@MrSubaru1387
4 жыл бұрын
Yes! For years now!
@unwanted_zombie
4 жыл бұрын
@@MrSubaru1387 I FEEL SO UNINFORMED
@jayp9299
4 жыл бұрын
I think you should get adapters and put some wrx wheels on it lol
@amauryfrias2662
4 жыл бұрын
Can i buy those stock wheels from you?
@lisonlili
Жыл бұрын
What is the offset of this rims? Thx
@robertelmo7736
Жыл бұрын
Can you tow with one of these?
@arelsigler3845
3 жыл бұрын
What’s the center bore and wheel specs?
@dieselnine1022
4 жыл бұрын
I'm sorry, but didn't watch the video. Just curious if you do work on vehicles other than your own. I took my 2015 Forester to the dealer today for some stuff... mentioned what you had thought was my problem with the a/c, and they said they cannot adjust the clutch gap. Wanted to sell me a new compressor. I'm in eastern TN and would be happy to have you fix, if I can get there in five hours or less. I'm an old lady, and just not interested in trying to do this myself.
@MrSubaru1387
4 жыл бұрын
Unfortunately, I'm currently not taking customers until my new shop is built. I'm in upstate SC, about 45 mins south of Charlotte, NC as a point of reference.
@dieselnine1022
4 жыл бұрын
@@MrSubaru1387 I hope your new shop is completed soon. I can go this summer without a/c. There is a chiropractor that I'd like to visit in Greenville, so maybe I could make a two day trip out of it. Best wishes for the speedy build-out of your new shop.
@dontno7240
3 жыл бұрын
Are they 4x100 or 4x114
@erinsonduran6663
Жыл бұрын
I'm having some issues with my 1999 Asia Towner (daihatsu hijet) when I'm doing 100 kmh on the dashboard it shows 45 mph on the GPS. The tires recommended for this truck are 155-80r12. I want to know if 13 or 14 would fix my problem 🤔 kzitem.info/news/bejne/05pvx6x8bJGmlKw
@timbrown9731
4 жыл бұрын
89 foot pounds yep 👍 lol
@japaneseminitruckimportsll7634
3 жыл бұрын
Facebook page: Japanese Mini Truck Imports LLC
@bbodan5393
4 жыл бұрын
Those factory rims are soooo ugly. Thank you you got a rim that's not black. You officially cast your personal character on the outside. Looking to see water turn to wine.
Пікірлер: 113