Thanks for watching Gang! Use code STUDPACK50 to get 50% off your first Factor box at bit.ly/3F55GCL!
@dallasarnold8615
10 ай бұрын
Hey Stud Pack, if you have not yet checked the comments from the last video, installing the 3 inch conduit, you should look at the ones talking about a slip coupling below the meter box. I learned it the hard way on my house. After years the dirt settled and pulled the conduit away from the house. What a pain fixing that when it could have been avoided had I known better.
@alexkemel4916
10 ай бұрын
If the other two didn't leak, why not compare the difference in the windows? Seems like it might have been a manufacturing mistake in that one window.
@steveloux4709
10 ай бұрын
Not sure what part of the country you are located, but that detail is more of a cold weather issue and always driven by utility requirements. No frost heaves in the Houston area!@@dallasarnold8615
@headcas620
10 ай бұрын
The problem with the nail fin is it pushes the window out making them look stuck on instead of adding depth by being inset in relation to the window trim. One reason new houses look worse than old ones.
@steigerbower
10 ай бұрын
At least you guys fix it when you mess up , construction work is easy to get wrong , there's a lot that can go wrong, I've a seen a thousand things that are wrong onsite and covered up by....... whoever ! Well in lads.
@jayperez6142
10 ай бұрын
As someone who does framing and finish carpentry for a living… nothing to be ashamed of. Mistakes are made, and we learn from said mistakes. It’s great to see a builder who ACTUALLY made a mistake and goes back to correct but in the process shows and explains why it’s wrong and how it’s fixed. Cheers to you guys! Nice build so far StudPack!!
@jonperryman6477
10 ай бұрын
The problem isn't with people who make mistakes and learn from it. Inspectors exist because there are a lot of builders who make mistakes and don't learn from them.
@jayperez6142
10 ай бұрын
@@jonperryman6477 Very true as well. Unfortunately in today’s construction era plenty of builders just want to fill their pockets and don’t care how projects are completed
@mytubebobbie06h
10 ай бұрын
Very well said!
@priceandpride
10 ай бұрын
Bella windows are the worst
@disqusrubbish5467
10 ай бұрын
@@priceandpride These are Pella...
@percival23
10 ай бұрын
There is nothing more valuable than a builder that is willing to show you thier mistakes. Well Done.
@SkulxCrusherx
10 ай бұрын
And there is nothing better than making a spelling misssteak when pointing that out.
@madebylife
10 ай бұрын
@@SkulxCrusherx
@ozziecrosby2092
10 ай бұрын
@@SkulxCrusherx Huh?
@thedevilshelp
10 ай бұрын
@@ozziecrosby2092their not thier
@mediocreman2
10 ай бұрын
Mistakes actually get more views on youtube.
@Dampalicious
10 ай бұрын
This is why we love you guys, I’m sure there are a few viewers that complain about seeing “the same thing twice” but I assure you guys it’s the vocal minority, when I watch you guys I KNOW that it’s almost always done right with attention to detail, and when it’s not I ALSO know you will show us where you made your mistake and how to properly fix it. It takes guts to show an error you made especially when nobody would have even known there was one off camera, this channel will always be known to me and many other viewers for its character as well as it’s craftsmanship and that’s a title you guys should be proud of.
@alexvega8026
10 ай бұрын
one of the worst things about modern social media and content creation is how content creators hide mistakes, failures, and other perceived negatives which are actually perfect teaching tools to learn from. this puts doubt into the minds of DIYers and newer people who want to tackle tasks on their own and in turn they give up a lot quicker since its demoralizing to watch a content creator do something "perfectly" the "first time" meanwhile less experienced people feel inept and are prone to quit a lot more quickly. massive props to you guys for not doing that shit. while the original install is considered a fail, you guys turned it into a teachable moment and passed on even more knowledge while showing people that even professionals are prone to making mistakes. again, props.
@markstipulkoski1389
10 ай бұрын
I love it. Paul can't say "vulnerable" so he goes with "susceptible" instead. I remember in elementary school when we all had to stand up and tell a little about ourselves to the class. My classmate had a heavy Southern drawl and pronounced "oil" as "erl". Even after many attempts, the teacher was unable to get him to pronounce oil correctly and he was flustered. So he continued his story, saying "My daddy works on a PETROLEUM rig". The whole class burst out laughing 😂!
@Onlooker71
10 ай бұрын
This is what I love about this channel. You’re human and you don’t edit your videos to look like you’re prefect. We all make mistakes and they’re the best learning experience. So this is a great video for us all to learn from.
@andspenrob
10 ай бұрын
Recommend against recessing the Zip on the concrete pad - you want a drip edge at the corner to avoid wicking action on the edge of the OSB.
@campaltd1092
10 ай бұрын
Great job guys. One thing you said was on the house you might step back the framing so as to make the liquid flash easier. Remember the edge of the zip is unfinished. The concrete will retain moisture and will wick up into the edge of the Zip. If you do that seal the edge of the Zip first and keep it off the concrete.
@JohnstonPettigrew
10 ай бұрын
Pella has been out there an awful long period of time to be discussing improvements to their instructions at this point🤬.....just a thought. Nice work guys as always!
@bhami
10 ай бұрын
I definitely fault Pella for not putting simple stickers on the windows saying that the installer needs to install the nail fins.
@mitchk7655
9 ай бұрын
I am amazed that they claim they cant install the nail fins at the factory.
@maddierosemusic
5 ай бұрын
@@bhami Yeah, wtf is that? I'd be more than pissed.
@kingdommanlegacyministries7769
4 ай бұрын
Hey, my thoughts EXACTLY...
@Darisiabgal7573
10 ай бұрын
I had the same pella windows installed on my house, the same drain ports after the factory certified installers left, i found on of the port doors on the window ledge. They are very flimsy. When you are spending 2000$ per window, you expect manf get details like that right.
@toitlepower
10 ай бұрын
You guys don’t hide the mistakes (that everyone else also makes occasionally, but pretends not to) and show us how to fix it. This is why this house is a great build and Stud Pack an even better channel. Without encouraging more mistakes the candour and honesty is what makes your channel. Keep it up!!!
@oldnstillworkin5709
10 ай бұрын
Man that’s BS! The manufacturer should take responsibility for this!!! Why the hell didn’t they send the fins with the units. 🤬🤬🤬
@AnthonyAttard-ix2cb
6 ай бұрын
Based on the video, I’m not sure if the flanges are just an option for these windows. Depending on how the purchaser wants to install them, would dictate if they need the flanges or not. Was it a situation where the stud pack should have requested for the flanges, being this home is a new build? Or were these windows engineered to be installed only with the flanges as a new construction window. If that is the case, then I would agree with you 100% and the manufacturer should have shipped the flanges with the windows being they don’t want to manufacture them in the facility to avoid damaging the flanges on such a large window in shipping.
@AnthonyAttard-ix2cb
6 ай бұрын
I hope this is the case where these windows were engineered and fabricated a certain way to only be installed as a new construction build, and need the flanges to be installed properly. Otherwise, I am hesitant to purchase replacement windows for my home because it seems they don’t hold up as well as windows with flanges.
@823Steve
10 ай бұрын
Mistakes are part of the learning. If you're not making mistakes, you're not doing anything. And nothing beats experience. Great videos guys.
@nmd14723
10 ай бұрын
Enjoyed the episode however really surprised Matt Risinger didn’t pick up on this in the installation video 😮
@StudPack
10 ай бұрын
we did the casements with Matt, and didn't have these big ones on site yet. He definitely would have said something.
@50sKid
10 ай бұрын
I think you should leave the sheathing hanging over the slab on the main house because water can’t possibly seap in through an overhanging seam. I know you’re going to liquiflash it but still, who knows what’ll happen to that in 20 years
@greemcreem
10 ай бұрын
one detail to consider on the main house is to zip tape the bottom of the zip sheets where they contact the slab, that way you have multiple layers of sealing protecting your siding. the zip tape handles protecting the sheathing, and the liquid flash protects the concrete to zip joint.
@bradfeatherstone1775
10 ай бұрын
For future planning: Before you start planting, rototill all of the beaten areas first as deep as you can. Also add compost or something else. Too many folks spend a butt load of money over many years after they plant grass trying to fix the problem of compressed soil. Or better yet just do edible trees and perennial plants front and back. Duplicate the multiple canopies that originally grew in Texas. Look up permaculture.
@AnthonyAttard-ix2cb
6 ай бұрын
What, wrong video dude?!
@margaretbear
10 ай бұрын
I think having the zip slightly proud of the foundation is good for water run off.
@abbyshackleton9198
10 ай бұрын
If I’ve learned one thing through renovations, it’s that water can show up in places you never though possible. And it stumps you. And makes you nearly cry. Glad you were able to fix it!
@lanon3277
10 ай бұрын
What I really appreciate is that when you mess up, you take accountability for it, and show how to fix it. Because in real life, people make mistakes all the time, especially on a new project... and the studpack house is work in progress. A work in progress is always going to be a learning experience.
@evatatus
10 ай бұрын
😩 that’s sucks guys! I just can’t see how it leaked with how diligent y’all were with sealing. In true studpack fashion tho, y’all give the story how it is, good or bad, and totally humbled. Much appreciated!
@92fsoakcreek
10 ай бұрын
Gotta say Stud Pack Gang; not only are you good builders; you're honest too. Some youtube builders would have just fixed it off camera and nevere admitted making a mistake. Home building is ALL about learning, making mistakes and then making it right. Cudos to the Whole Gang for standing up and helping us make things right. !!!
@SPCMCERV
10 ай бұрын
What a bummer, having to redo those GIANT windows. Props to you gents for taking the time and making the effort to fix! Always disheartening when you find a mistake, but feels great once it's fixed!
@vannk73
10 ай бұрын
It's amazing how you all can stay so positive through all the little mistakes, delays, and do-overs. Despite the setbacks, this garage is looking great!
@FlakMagnet
10 ай бұрын
I really appreciate the energy of the dad deferring to his son because it's his son's house. At the same time, the son is being respectful of his dad while still doing the "my roof, my rule" thing. The mutual two-way respect between parent and child is fantastic. If the youtube personas are sincere reflections of their actual familial dynamics, (I think they are) then that's a model family people can hope for, folks.
@davidwayneprins
10 ай бұрын
love how you own up to your mistakes and correct them. Makes me wonder how much Bob Vila left on the cutting room floor so it looks like he did it right the first time.
@disqusrubbish5467
10 ай бұрын
Norm did it right...
@scottmalone9161
10 ай бұрын
It the consistent showing and fixing your mistakes that make this channel so valuable! Like in so many things it's the details that get you intro trouble. Great work, I hope one day I'll be able to put it to use building my own custom home in the future!
@cosmicbrambleclawv2
10 ай бұрын
The windows might not have been watertight but one thing that always is, is you guys! ❤ Ready and willing to admit when mistakes/accidents are made, and even better: more than willing to show how to fix it when something happens
@realkacy
10 ай бұрын
The house will be very tight. Make sure you are getting the hrv/erv right. In the garage, make sure you have a way to move the air. If you start the car, fumes will linger around. Since your house is very tight, you might consider going rockwool rather than using spray foam which can be a headache. R value on the roof though might be an issue.
@irfisher
10 ай бұрын
Guys - I enjoy your video. Glad to see you added the liquid flashing. One additional thing I would recommend on the ZIP sheathing is folding tape around the bottom edge and avoiding direct contact with the slab. It’s a lesson I learnt as it was a detail i missed and the ZIP rotted out in less than 3 years in Houston. The moisture wicks into that exposed edge if it’s touching the slab or rain is bouncing off the slab onto the edge. I can email you pictures of what happened if moisture is left to soak into the ZIP via the exposed edge then left to basically steam behind the siding in hot texas weather. All the best Iain.
@erict7499
10 ай бұрын
i did something similar on a garage a few years back i had access to again (swapping a light fixture out). i wrapped the bottom edge of the sheathing in zip (in my case plywood). and that was sealed (similar to lexel but i forget which product TBH) to the sill plate and footer. in my case my dimpled housewrap is also taped to the bottom of the sheathing. but this means no extra step sealing below the installed sheathing with liquid flash or whatever. F that noise. Portland, OR, rainy AF, sheathing right above a concrete patio. no rot. bugs and mice inside because of the garage door. so good luck sealing that thing. ;-)
@greatvalleyone
7 ай бұрын
When sealing in conjunction with zip tape, always wipe zip tape backing with alcohol to remove release agent, it gives a better adhesion between the two.
@DarKMatter.1
10 ай бұрын
I love how you guys show us your mistakes and how you fix them because those are probably some of the exact mistakes a “DIYer” would do. Excellent job on the garage and video fellas. Can’t wait for the next one.
@Tool_Addicted_Carpenter
10 ай бұрын
Always bittersweet to do something over. You're not alone. I absolutely hate how all the higher end windows come with the fold out or snap in flanges, whereas the mid grade vinyls come with the massively superior molded flanges all the way around. I can't figure out why they do that other than maybe ease of shipping. I ran into some issues with some very high end Marvins where the top flange didn't even overlap like you show here. You could see daylight in every corner after install. They sent corner flashing pieces but no way I trust them long-term, which is unfortunate because my name is on the install. Knowing they weren't going to make any shifts in production solely on my account, I still had the rep come out and look so I could express my concerns. We had a minor pinhole leak in one window during gailforce winds and terrential downpours, but I could only add Lexel and trim and hope for the best, which I absolutely hate doing. Couple of notes- an old timer I worked with always set his window ROs slightly taller and put a piece of cedar clapboard on every sill before flashing tape and window install so that any water would automatically drain out. -Something I do with all my 1st rows of sheathing is wrap the bottom with a run of zip tape to completely eliminate wicking. For the future, you should really run your sheathing ~6" beyond your sill plate down past the foundation. -Lastly, you want to do the same with your bottom flange as you did with the top by having your bottom flange run long and behind your side flanges. Awesome video as always guys and I really appreciate and admire the transparency. Customers are surprised when I'm actually honest about issues when they ask how everything is going. I explain both the problem and solution and they always have a look of concern on their face right up until I tell them it won't cost them anymore lol. Then it's just a sigh of relief and appreciation.
@nathanpreston2263
10 ай бұрын
I appreciate the Integrity. Keep it that way Gentz! I never comment on anything but, dealing with Contractors, etc... it's nice to see a builder that owns up to it. It helps us little guys too. Cheers.
@kirbypmorris
10 ай бұрын
I have installed many many windows of many manufacturers and also worked exclusively installing for Pella for years. It is not uncommon to install windows without a nail fin ... like in an opening of a house covered in brick. They have a brick mold that snaps in to fill some of the gap but you still need to caulk of course. It still always made me nervous that they might leak over time. But in sunny California they seem to be fine. Always always put a nail fin on if you can. Pella also has adhesive flashing tape that is made for the left and right corner joints of the fin. . And yes ... always leave the bottom fin not sealed with caulk. Let that water get out if it does get in. And water test for at least 10-15 minutes. Sometimes it takes awhile before a leak starts to appear. When stucco or siding is on ... water test for 30 min.
@hu5tle-
10 ай бұрын
I recommend just using Siga Fentrim tape over liquid flashing the sill on the main house. As you experienced, the liquid flash goes fast and it gets everywhere.
@mikeinmaryland
10 ай бұрын
So glad the window is proud of the Zip. To be honest I think the salesman did you a favor, given the fact the window’s size and weight. Meaning you could install them from the inside with less “pucker” factor. Not sure why he didn’t include the flanges. Finally, I like that you’re building a house, with a Remodlers eye. A lot of builders don’t think five steps ahead when building.
@SeaHorseTeeth
10 ай бұрын
Maybe it’s been said…, but it’s only a mistake if you don’t fix it. Your keen eye for detail and ability to explain these processes is phenomenal. Most of us are good at one trade and you guys are crushing all of them. See you on the next one.
@CASHCRZZY1
10 ай бұрын
Go watch Matt Risinger “five better ways to framing “he give us a good tip on how to finish the bottom of the house with that zip R bored. He shows putting a piece of treated lumber at the bottom of the zip board along the foundation, and then ceiling. You’ll have to check it out.
@BerryMcCaulkiner859
10 ай бұрын
I noticed on the first window video that they were sitting in pretty far, and I thought maybe it was going to be brick. Your going to be thankful it leaked so now they are sticking out correctly for siding
@rosss7007
10 ай бұрын
33 year old dad that loves to DIY here. Can’t tell you how often I make little oversight type mistakes or have to run back to the hardware store 10 times for a “30 minute project” Seeing that you guys do the same will make me wayyyyy less hard on myself in the future. Love the series, I click every new video as soon as I see them. You guys are awesome!
@jonperryman6477
10 ай бұрын
The one recommendation I have for you as a DIY'er is to stress anything important and fix any problems you find. Note that Studpack did a water hose test to ensure there was no leakage. I've seen a lot of DIY'ers not take basic steps to find out if they have a problem. The most memorable being 2 guys at a rebuild together project installing exterior metal handrail on the steps but not one screw hit. After they left, I walked over and effortlessly lifted it from the brackets. I have no problem with making mistakes but they never recognized they made a mistake.
@FredD63
10 ай бұрын
I think it’s better that your sheathing sticks out away from your foundation as it lets water run down your wall, and drip away from that sealed area keeping water away from that seem
@hrcnick11
10 ай бұрын
I feel like a metal drip edge would have been easier to seal.
@ericzeigler8669
10 ай бұрын
I agree. Stud Pack's jobs are nice ... because they do them twice. If your Zip panel is flush with the concrete foundation then water can wick up through the foundation and start to swell the edge of the Zip panel. Do you really want to do this job again? Do your main house like you did the garage and you'll have no problems.
@sweepingdenver
10 ай бұрын
Full agree
@baxtronx5972
10 ай бұрын
Is it possible to put a metal edge behind the sheathing?
@fredkk79
10 ай бұрын
Why not zip tape the bottom piece of sheeting before install
@FrankGraffagnino
10 ай бұрын
although, if you flush the zip with the slab, you won't be able to completely seal that downward face of the OSB... i think sealing that up so it can't wick up moisture is a really good thing. So consider that if you move the framing back. Great job guys!
@ThunderDivine
10 ай бұрын
Man wish these episodes where 2 times longer. - It looks like tinted windows from the streetview. Amazing job. And rain here even goes upwards and in circles.
@kyakukid1
9 ай бұрын
This is why I love this channel. This channel is so informative, honest, and humble about how it does things.
@daytonpyro
10 ай бұрын
maybe i missed it. Pella didn't supply that piece?
@toniandersen6049
10 ай бұрын
Hi. I think the reason was that there had been condensation on the window surface, and since this was the last window you put in and furthest away from the stairs, all the moist and warm air in the garage was concentrated in this corner. and since glass does not absorb the water. I see the same thing in my own garage. Greetings Snekkerandersen (Norway)
@outoftheboxmedic1608
10 ай бұрын
I love that you didn’t fake it with the window installation. Man it could have been easy to just move on and not even mention it! But you didn’t! THATS INTEGRITY! You’re true to yourself and others about mistakes. We all make em and then go to KZitem to learn how to fix them. This is a perfect example of that! That’s what makes me love this channel about! Seriously, I tell everyone about this channel! KEEP UP THE AWESOME WORK!
@DBlow2003
10 ай бұрын
Always show your mistakes, that's what makes your channel unique. There are hundreds of DIY carpentry channels out there where everything just magically fits together and always works perfectly. Those channels are heavily edited and don't reflect what really happens on the job site.
@JamieReneeVonTeez
10 ай бұрын
In life, I have learned to ALWAYS do it right! Integrity and pride in whatever you do and put your name on! Great job guys! Good to see these occasional flubs that educate and prove your not perfect advanced aliens!!
@macrapidito1
10 ай бұрын
I saw the mistake on your window installation video Minute 26:43 that was the mistake, that was the reason the windows where “leaking” . All windows leak or eventually will leak, the problem here is that in your effort to air tight the house you also installed a water trap, you could do backerod and silicon on the sides and top but not at the bottom of the window, that’s where the water drains out. When you installed the backerod at the face of the house you installed a water trap. You could use the backerod and caulk all around the window but only on the inside. Out side just 3 sides, sides and top. How ever if you are doing new construction , windows with nail fins are the way to go. Love your videos, keep it up Btw, I am an stucco contractor 😬
@JT_70
10 ай бұрын
An advantage of Lexel over silicone sealant is that Lexel will stick to itself unlike silicone which will not adhere to itself. You don’t have to scrape every little reside of Lexel from the window frame to reapply it. Most contractors would just apply caulk to “fix” the water leak and would not remove the windows and go to all that trouble to find the cause of the leak.
@ppomm
10 ай бұрын
The biggest principle of any DIY project, is being willing to do-it-again when needed. Usually about 1 of 3 things we do needs to be taken out and re-done to make it the way we like. Lots of savings, but occasional re-dos part of the game! Always like your videos
@DK-xv3rc
10 ай бұрын
A blower door test would be cool to see when you’re done. And then compare between the house and garage
@Dragonited
10 ай бұрын
Good that you liquid flashed the bottom of the zip sheeting and the nail holes at the bottom row, though you are not required to do so it's good to liquid flash all the nailholes, if any nails have gone bellow the green layer they shoudl definatley be liquid flashed. The roof is also good to cover the nail holes though it depends on how your climate.
@robertrussell5210
10 ай бұрын
Oh - and I have made safety mistakes too🤗 I don't recall from the installation video how you sprayed it down, but my sense is if you used a high pressure squirt of some sort it went in through the weep hole and filled the bottom tray of the sill
@cogspace
10 ай бұрын
Love the way you guys redid the windows. I was a bit worried about the long-term before since (say it with me, folks) everything leaks. Glad you found and fixed the issue now rather than 5 years from now after it wrecked a bunch of your hard work! That window may not be bulletproof, but it definitely looks properly water-resistant now. =)
@stuarthallgren9380
10 ай бұрын
I learn just as much or more from your recovery from mistakes or oversights. Mistakes are a pain and I just as soon learn from your mistakes rather thane mine
@mesister3862
25 күн бұрын
We all do research for our projects, and sometimes we have to redo. Appreciate your honesty!!
@slypig24
10 ай бұрын
Thank you, I'm learning more from you guys than any Web site or any technical Bulletin that available. Thanks for a great factual channel.
@vonderdornburg
10 ай бұрын
The details about how some windows come with it without nail fins were totally new to me. Glad you caught it! It's looking good!
@dessertbooger9397
10 ай бұрын
You guys are doing well. If you really want to up your game there's a couple extra things you can do. 1, set your framing back the thickness of your sheathing. 2, add some Z flashing behind your sheathing as a cap on your foundation and leave a 1/16"-1/8" gap ( use washers as easy spacers ) and then fill the gap with liquid flash. 3, use liquid butyl rubber in 5 gallon buckets on all foundation areas ( exposed, undergrade,and as additional air,pest,water barriers ) 4, Roll and brush liquid rubber underneath and behind all your potential water areas, including drilled holes ( reason being that in the event of a material failure, the underlying areas won't take any damage and are cheaper to remodel or upgrade in the future. 5, add side flashing and caps to all windows and doors for redundancy. 6, add coating of liquid rubber underneath all siding. This only adds a couple thousand dollars overall to the price and turns an entire home of OSB into a waterproof, swellproof,custom home.7, Avantech makes great mechanical rooms and home Safes.Great job guys,keep it up.
@carolinepaltz324
10 ай бұрын
Up here in Oklahoma, we had a contractor bid our new building. It is a post frame building with steel siding and he has the concrete guys make that ledge for the siding for the steel to sit down on to close off the bottom of the steel and prevent bugs and rodents from getting access to the building from the ribs in the steel. Hope that made sense, anyway nice video and nice job on the corse correction on the windows.
@ds61821
10 ай бұрын
I was confused by Pella not sending the nail fins if they were required for proper new construction insulation. I had cheaper vinyl Pella windows I installed in a new room addition 11 years ago and the nailing fins were attached already to the window. Your nailing fins are not what I guess I expected--and it's not surprising that you would not use them the first time around. Sorry you had to redo your installation, but you now know for the house build and we can learn too about window installations,
@KingOfChins
10 ай бұрын
Never has someone been so glad to have rain before dry-in
@808jpm
10 ай бұрын
I'm trying not to imagine all the little mistakes most builders are making and not going back to fix. Good job going back to fix the windows.
@Mines619
10 ай бұрын
Don’t forget the 3” expansion coupling for your electrical line in from the city to your panel. That was a great recommendation on your last video
@davidgiesfeldt6650
10 ай бұрын
If you are still concerned, place a single layer of paper towel on the inside sill. If there is a leak you will see the EXACT point where it occurs. I have used this method for years when working on old plumbing. Last thing you want is a client telling you a leak damaged the inside of a new cabinet. Same method, two uses. Kudos on the redo, thanks for sharing.
@marcleblanc7021
5 ай бұрын
At least you caught it and fixed it. But for as expensive as Pella is, they should have included all necessary hardware to install it correctly. Not sending the nail flanges is sort of messed up. If you had seen them in the package, you would have definitely installed them. But seeing those little details has taught me so much if I have run into this. I will know to get the fins. Thanks for sharing Studd pack. You guys could have kept to yourselves.
@amlearntodoit8168
10 ай бұрын
Just installed Anderson windows, glad I checked inside those flap doors for water to escape. Because they had plastic covering some of them, that had to remove with little pliers. So hot tip, check inside those little doors, to make sure water can flow out. If they leaked? Anderson would of blame installation, when it fact it was their lack of detail manufacturing inspection detail. Sorry about your redo on windows.
@kevinmckenna9601
10 ай бұрын
Stud Pack...Window detectives!!! I don't care what Pela says...in the field, the hose was your best option!! Nice work.
@SaucyOperator
10 ай бұрын
They make great windows. So does Anderson.
@kenty2831
10 ай бұрын
On one of the videos, there was a outside wall overhang of the perimeter wall to the foundation. You sealed this with a glue product, similar to Henry's roofing. I typically see this overhang, to allow rainwater to sheet drain away from the sill plate. Curious if you make the wall flush with the foundation would this promote water retention? Enjoy the videos
@jordandupont8192
10 ай бұрын
I think Matt Risinger needs to own a little here too lol I'm glad you guys figured this out and I am happy to learn from it also.
@boppins
10 ай бұрын
Thanks for showing your mistakes. It's good to show others that mistakes will happen, but more importantly, you can fix them. Just need some time and patience.
@Adesico87
10 ай бұрын
Hats off to you guys for taking the time tracing down the issue! Matt Risinger takes dyed water, and does the exact same water test you did- cover weep holes and fill the bottom sill. He’s proved that even high end windows can come from the factory defective. It’s a great test, but I honestly can say no one in the Kansas City market tests new windows before they’re installed. Wish it was a common practice.
@alantittle299
7 ай бұрын
I would suggest waiting as long as possible after the power wash, but maybe you did with rain in the forecast. Every bit of moisture you could evaporate before the Liquid Flash may be worth it. The roach and silverfish sure seemed prepared. That being said I sure would like to see no green at the edge, but there were several exposed edge bands. As tenacious as water is and slow drying as Houston is I hope you use one more tube to truly wrap the LF along every inch of edge, not just under, hoping no water creeps to and under the Zip green barrier and into to OSB, possibly repeatedly. These are great informative videos. I need to know as much as I can to supervise or GC my build a couple hours north. I appreciate your commitment. One other foundation seal is the Fentrum Tape, which seems to seal to foundations and all the Huber products. Maybe it is a Huber Product. Matt Risinger mentions it from time to time.
@andrewsackville-west1609
10 ай бұрын
Inspiring to see the ownership and honesty! Nice job! Bonus, now you've been able to observe the effects of your lexel application when you pulled them out.
@bchluvrxyz816
10 ай бұрын
Best contractor’s video out there. They own up to their mistakes, AND, actually fix them. Properly. Most contractors would just caulk the hell out of the window, believing that is a real fix. Not. These guys are how all builders should be. I would trust them to build anything for me.
@mrsduddlycross
10 ай бұрын
This is a really cool video! I work at one of those big home improvement stores and recently transferred to the millwork department. My coworker and I are both new. Today I did a reorder for a customer who wanted flush fins but got a block frame instead. A combination of inexperience on the part of the purchaser and my coworker the salesperson led to a miscommunication. Mistakes happen and we learn from them. Videos like this help me better understand what I am selling. Now I look forward to all the door installs!
@AnthonyHernandez-p8e
10 ай бұрын
Love the father son duo thing. My old man & I are electricians, he has over 30 years of experience & have 7 under my belt. I hope that one day I can teach my own son what it means to work hard. I might just have to grab a camera & start capturing my own adventures. Good luck with the build! Peace & love.
@rj7826
10 ай бұрын
I think you've got your water problems nailed with the fin installation😏 + the ZIP Tape & Lexel. Perhaps the next video is garage doors? Not only for weather, but site security. I don't think it's something you guys have covered in a video🤔, but I would think it's a concern - given all the tools and materials you have on hand. Looking forward to the next one.
@T.E.P..
10 ай бұрын
absolutely incredible how fast you guys blasted into the universe ... It's been a huge delight and super educational being subbed all these years. well done gentleman!!!! Super happy for your success. I used to click LIKE on every comment on the vids ... now it takes days to do what took me 10 minutes. Cheeers guys
@timhelmuth9740
10 ай бұрын
I really appreciate how you are willing to share your mistakes. Not many channels would do that.
@geniferteal4178
10 ай бұрын
I love all these helpful videos and explanations. my biggest concern is if you don't do it yourself, Who's gonna put this much care into someone else's project? I bet most contractors would do their best and close it up never knowing if it leak like this or or caring.
@eastcoastmodz5195
10 ай бұрын
WOW that looks great ... I could really feel your 'pane' with the windows LOL. Another great video by the Stud Pack Crew! Can't wait to see what's up next! Cheers Paul, Jordan and Rad :)
@Zt3v3
10 ай бұрын
This makes me feel better about myself. Believe me, you're not alone in having to do things twice.
@JonathanOsvath
10 ай бұрын
Redo’s are the worst. I’m a DIY’er and have had to endure the pain of redoing a part of a project due to changing the plan or finding out afterwards through research there is a better way. Keep up the awesome work y’all are doing, I love the channel.
@phylliscage
10 ай бұрын
I’m beyond impressed with you guys and the way you always make things right.
@timderks5960
10 ай бұрын
I've learned more from other people's mistakes than from my own successes, so please never stop showing mistakes.
@kingdommanlegacyministries7769
4 ай бұрын
I've NEVER REALLY liked 'replacement' windows...often you have no other option but I AWLAYS, whenever feasible, like to use windows w nailing fins. I also like to use a 1 1/2 or mostly 2" aluminum roofing nail to nail my fins. Every other fin hole is quite ok... however, I have removed old windows when I'm replacing new windows & inevitably, some clown used like 5 nails for the whole window. Also, I think nails are super ok rather than screws. Nails are super flat, as opposed to screws which stick out a little... I HATE that. Just sayin... Studpak broskis, your doin just fine...don't mind us... too much... And by the way, I'm 65, still kinda putzin' on small to medium jobs, I can be somewhat selective, & I LOVE to still be learnin'... I love doin' decks, siding & window...outside stuff... Yup, do the other 2... it's a couple hours at most w 3 "Studs" ... so "JUST DUU ETT"... One LITTLE thing that makes me a LITTLE crazy is... you guys are ALWAYS doin' stuff on the floor... 3 horses w/ some lumber or ply... work at a nice height so the work is easier to see, access & accomplish... just sayin'... NOPE... put all the fins on NOW... slide the window out, nail it in... bingo bango bongo ALSO... one of my 'best friends' is dish soap... put a dribble on the window where u slide the fin on... it will slide in like a greased monkey... you guys should invite me to one of your jobsites... just sayin'..... Zip bottom 1st, then sides but run it up 4/5" past window, then zip top... Also, I almost ALWAYS have some kind of a rag in my nail pouch, I like a nice cotton t-shirt kinda rag, & use the rag to run up & down your Zip instead of just your fingers. You'll be able to press harder w/o destroying your fingers... just sayin'... Also, do zip on bottom, just run it on the fin & not up on the window... just sayin'... I also do one or two little things that are slightly annul... & that is, cuz I usually have a lot of tools out per each job I'm doin'.. is a cordless drill, sm drill bit, silicone behind window frame hole, install shims snug, predrill thru shims, run your screws. I use a lot of different metal flashing applications in areas like the bottom of a wall I would have some heavy 6mill or even some med weight tarps to put over those two big doors, keep out the weather
@surfingcuriositywaves4046
10 ай бұрын
While you have that great access to that foundation skirt, apply a good chemical barrier against the termites. As always, check local codes. Later, you may apply a plastic skirt to take the water away from the foundation, so this is your chance to let those chemicals get under that skirt and stay close to the foundation.
@unifairsum21
10 ай бұрын
The most valuable lesson learned are the mistakes you made along the way taking accountability and fixing them is how you grow glad to see you guys doing that
@franklong6269
10 ай бұрын
You don't want to flush your Zip sheathing with the edge of the concrete stemwall because if there is an opening into the house for some reason, all the water flowing off the Zip will enter the house at that point. Having the Zip extend past concrete creates a natural drip edge.
@billsnyder6945
14 күн бұрын
You guys are real and honest influencers, fessing up in admirable fashion when it is too late for shoulda, coulda, woulda. Bravo! Sometimes you learn more from mistakes than just being shown the right way. I wrote a whole song about this. One line is “it’s the perfect how to of just what not to do.” I am installing a small new window during a bathroom remodel, only happened to find a video (from your buddy Matt actually) where I found out zip tape will not stick to my celotex sheeting. Matt used a mastic no longer available. Even when I went to search out this issue and try to find out out other solutions there was no information. I contacted zip tape manufacturer Huber, salesman never heard of it, he copied email to technical…crickets. Pella 800 number referred me back to local store and salesman who had no clue. Finally the salesman asked their fix it guy and he said it does not sick because it is porous and toprime with red guard. $55 for a square foot! I expect that will work but wish there was a cheaper easier solution.
@chuckthetekkie
10 ай бұрын
I love the fact that when you make a mistake or something goes wrong you show us. That shows us that you will gladly admit when you make mistakes AND it teaches us so we don't make the same ones. LOVE IT. Can't wait for the next video.
@bobfarrell6510
10 ай бұрын
Most builders would have let it ride... glad to see you are doing it right.
@johnterryjr.2242
10 ай бұрын
Thanks for being transparent, you could of easily fixed this off camera and no one would of known!!! At least I'm not the only one who has to do it more than once...lol, good job men!!!
@greemcreem
10 ай бұрын
heh... transparent... heh heh about windows.. hehh heh transparent windows heh...
@franktowers3
10 ай бұрын
the water was coming out of the weep holes and sitting on the sill, once yall put the flanges in the window stands proud of the wall allowing the water to roll off
@rjcontra
10 ай бұрын
ACCORDING TO MY VIDEOS I'VE set up in your home. It was your neighbor. He came over and poured water on that sill. He was going to do the others but heard a noise and got spooked. But yes, nail flanges on all windows on new construction a must.
@agray103
10 ай бұрын
Way to own the mistake and learn. Albeit the mistake not entirely your own doing. I’m a bit disappointed for you guys that Matt didn’t catch this while he was there. Love the videos and hope the next part of the project is going better than anticipated 😊 Thank you for choosing to share with us
Пікірлер: 730