"I mean this guy...you know, he's got a shirt on." Well, I'm sold on that Dicor roof coating for sure, Chuck! LOL
@Dealyo1
6 ай бұрын
Gotta just throw it out there that this is not the recommended order of applying these various Dicor products. Based on Dicor’s recommendation application goes: lap sealant, cover tape, primer, coating. Their lap sealant needs between one to two weeks to cure fully before anything goes on top of it. Might not be as important for CC because it sounds like his rig is free of leaks to begin with but if you want to go by the book Dicor recommends the above order of operations
@wordslinger277
Жыл бұрын
Charlie, that bus is truly a thing of beauty. It is your grand thesis of everything you've learned on this journey. I love it. And I'm jealous of that roof! (I wish we both had known better five years ago when I Tropicooled mine ... you're right, it gets dirty.) I'm also thinking about contacting Wes to paint my bus. Hell, I was following Transcend Existence before I even met you. When I realized he was painting your bus, I thought COOL! Anyway ... your bus is looking awesome!
@ChuckCassadyYT
Жыл бұрын
Yah dude! Your bus was the one that inspired us to figure out a better way
@michaeldeckert6023
Жыл бұрын
You are one great teacher.. The paint on the bus is stunning. The roof and it's perfection, as well as the whole build shows your incredible knowledge. Taking us along on the each time is an adventure truly enjoyed.
@robertkiell
Жыл бұрын
what about idea of using bedliner on roof???
@AdHocAtom
Жыл бұрын
Dicor is great! I'm doing a bus build now so it's less of an issues but on my last RV I even ran a V at the rear with the lap sealant just to channel some of the water away from the rear fiberglass back cap. But like you I always tend to have 3 layers of protection, I build everything to last 50 years when me and the bus will likely be gone in 30 / :
@Thadbrown95
Жыл бұрын
Chuck Cassady for president!
@MatthewRobertHenry
Жыл бұрын
Crushed it, buddy! Haha, I got nervous when you were rolling primer away from your ladder, then I remembered you don't have a flay nosed bus 😂. Stoked to see you at the bus fair!
@AndrewHemstreet
Жыл бұрын
Those ribs on the exterior of the bus roof are an older Thomas design. It's on my 2004 flat front but not the 2004 FS65 my friend has. The twin to the 2004 flat front which is 2005 has a smooth roof, fun fact 2004 has exterior riveted walls and 2005+ Thomas are all Philips screw exterior.
@kylethecreator
Жыл бұрын
Not a complicated task but you always make sure to talk about every detail!
@1anita1m
Жыл бұрын
It's looking more and more awesome every time. Love what you are doing. I am so looking forward to see it all complete! Love it!
@arthurperrea3714
Жыл бұрын
Nice job
@buckjones6334
Жыл бұрын
Once again great information! Your videos are very entertaining as well! Thank you Chuck!
@indogyrsimdead
Жыл бұрын
These videos & your channel is invaluable to someone who wants This lifestyle thank you so much! for being a stand-up guy & posting this Valuable information for free
@TomBryan
Жыл бұрын
No Sunday night video and I'm getting the shakes.... I'm addicted to Chuck Cassady Skoolie content.... Hope everything is okay.
@TheSerenityhuck
Жыл бұрын
I also have an old Thomas bus, which has those stupid outer ribs on the top running the length of the roof. After many months of frustration, I'm just going ahead with APOC #109. So far it bonds really well to the steel.
@brycestewart3181
11 ай бұрын
FYI, I just used the Dicor Sealant "self Leveling" I think a lot of people think it will level more then it does, so don't use extra or you will have a bump/line that I will be placing the tape over, I rolled my dicor self level to flat. Also, once you put the tape on, it says to prime and coat right away...... Good luck
@cart3685
Жыл бұрын
Awesome timing! I was kicking around how I wanted to paint my roof!
@Dr.PhDeez
Жыл бұрын
I used Dicor on both of my buses and so far haven't had an issue. didn't use the tape, but the primer and paint seem to do the job.
@ruben8114
10 ай бұрын
Hey bro, just wanted to say: love your video's! Great content/tips & tricks and especially like your chilled intro & outro's! Gotta love the jazz.
@bgtyhnmju7
Жыл бұрын
Great video. Excellent camera work :o) and some good info.
@SandyTheSkoolie
Жыл бұрын
Great video
@KindleMcGuinness
Жыл бұрын
… lol … “if that doesn’t convince you then just leave!!!” …. 😅 You are awesome 😎
@checkoutTinyHouseTravelers
Жыл бұрын
"and this guy has a shirt on" is an amazing line about how absurd some marketing is.
@ChuckCassadyYT
Жыл бұрын
Exactly
@leerichards6844
Жыл бұрын
Looking good Chuck - I’ll be doing our roof in the next week or two, so perfect timing! Dolly is getting closer to launch!😅
@ChuckCassadyYT
Жыл бұрын
That’s awesome!
@user-dq4td8eu7y
Жыл бұрын
What model of solar panels are up there ? They seem huge to be able to reach from one side to the other and yet still over hang. This channel is cool because where able to learn the best ways to do things. Thumbs up
@ChuckCassadyYT
Жыл бұрын
They’re just residential panels. Super common!
@BigDaddyOworkshop
Жыл бұрын
Aw man... I just painted my bus roof last week with Tropicool. I hope mine gets dirty soon. it's SOOOO shiny! my roof if very rounded so you can see the roof coating from the ground.
@AM50red
Жыл бұрын
That guy's got a shirt on in every shot of him!
@ChuckCassadyYT
Жыл бұрын
some one gets it
@mikedsobe
6 ай бұрын
Thanks ,,,, great vidéo very usefull for my project
@richardvargas3983
Жыл бұрын
Thanks for the video Chuck. I am preparing to paint my bus roof and have been agonizing over which type of paint, and which product, to use. I appreciate your insights and experience. I had a question about dealing with holes that have not yet been drilled. I will be installing a deck, hopefully bolted into the vertical surfaces, and solar panels. Would you recommend placing something like Eternabond tape over the holes before passing the bolts through? That it would function kind of like a washer. Thanks!
@367scotty
6 ай бұрын
Have your ever dealt with a box truck roof. Mine is transparent fiber glass. not sure if i should rubber membrane it or fiberglass panel with insulation. Any thoughts. great channel great no bull tech.
@mrschmiklz
10 ай бұрын
I thought I was looking at a backdrop of my shop for a second @3:18
@livingworkingoutsidebox
10 ай бұрын
Wait you said this was your preferred method to paint a roof... Then in the beginning you said.... 1:45 It's a system you haven't used before...just a part of it....🤔🌬♨️🎈 Just busting your ⚽️⚾️🥎🏀s 😊😅 17:26 Looks good 👍
@ChrisYevrah
Жыл бұрын
I will never understand how you don't have more subscribers
@ChuckCassadyYT
Жыл бұрын
subscribe!
@billydagenham
Жыл бұрын
Thanks!
@johnkaznecki3842
Жыл бұрын
Nice job
@marsrover001
Жыл бұрын
I was unhappy about the price of tropicool, this looks more reasonable and comes in one gallon instead of 5. Unfortunately I did use some silicone caulk when putting my roof together, can I just tape over it with the seam tape and paint?
@mikeschmalz2031
11 ай бұрын
That solar cable gland housing is a nice design. Do you have a part number or link?
@NewfyORE
Жыл бұрын
How does Sikaflex 221 compare as a lap sealant?
@_WADE13x
Жыл бұрын
I had my roof Rhinolined and painted white
@alanhat5252
Жыл бұрын
when & how well is it holding up?
@1982MCI
Жыл бұрын
@@alanhat5252 it will hold up well if the surface was prepped correctly and with him painting it white will give home a good reflective surface to repel the UV rays that could otherwise penetrate the roof and heat the interior but it will not give it the sealing properties against the rain that the Dicor or other similar sealants can or will. It depends upon how thick it was applied also, but it’s still has the potential of not dealing around all of the rivets as the Dicor will, but it will help and as long as it’s applied correctly, will last a long time. I’m going to be applying the Dicor to my roof as well for these specific reasons and I do have extensive experience with both. Good luck on whatever you choose though. Just do your research on both so you can make an educated decision on what is best for your situation.
@CharlesWilliams-zp4mq
2 ай бұрын
Would a 2" xps panel spray foam glued to an aluminum skin on one side and 3/8" plywoid on the other be a good way to build insulated panels for a diy camper?
@alexshiver5418
Жыл бұрын
Got the same color scout.
@ChuckCassadyYT
Жыл бұрын
Yes!
@billydagenham
Жыл бұрын
Man, your timing is impecable. A few days ahead of everything I have done. It’s been wonderful. But here’s a question, why are you able to paint over the di or sealant?? The instructions say to do that, but won’t the paint prevent it from curing??
@missingegg
Жыл бұрын
Chuck, another great video! Question though: did you put sealant down when you were installing the solar entry gland, the roof fan, and the solar rack feet? I think they answer is "yes", you used butyl rubber, but it's a bit hard to tell from your commentary. I'm following along on your videos as I do a similar project with a cargo trailer. Boy do I wish I had the curved roof of a school bus to shed water better. My trailer is a flat roof, and I'm worried it's going to be a nightmare with pooled water.
@madelynnmoore2802
5 ай бұрын
Has the tape ever been used on vertical seams? Like on the side of the bus?
@madelynnmoore2802
5 ай бұрын
I have a 1993 charter bus I am converting with my husband. We finished the demo, subfloor, and reskin. Before moving forward we plan to seal the roof and paint/seal the rest of bus. Then begin putting in the new exterior lights, windows and so on. The tape is an attractive way to add another level of sealing power.
@billydagenham
Жыл бұрын
I just did this, and now I have sitting water on my roof between the frame rails because I sealed them. time will tell what the implications of this are
@edsteward7717
Жыл бұрын
I looked, and it's quite a bit cheaper than the silicone. Curious if it lasts as long.
@TricksterDaemon-jw9hi
3 ай бұрын
'Nothing sticks to silicon! ...except dirt"
@nicholasphillips5406
Жыл бұрын
Great stuff Chuck. Appreciate you sharing the knowledge. One question if you have the time: bought mine as a partial conversion and the prior owner tropicooled the whole thing straight out of the gate, i.e. he went over the stock emergency exits, EVERYTHING. I have most everything that’s on your bus roof yet to be installed on mine. When the time comes do you have any advice on how best to mount given that preexisting tropicool? Would love to not have to remove the entire thing smh. One thought was to wire wheel or sand it back to bare metal just in the areas of install but I’d be worried that where the new paint meets the silicone that there’d be a weak point. Does eternabond bond to the tropicool? Maybe that could cover the seam. I know you mentioned that Henry has their own sealant so I’ll look in to that. I’ve been using sika 221 everywhere else. Thanks for your time and content! The bus is looking like a freakin masterpiece. Can’t wait to see more
@nicholasphillips5406
Жыл бұрын
@ChuckCassady just following up in case you’ve got time to share any sage input oh wise bus one 🙇♂️
@evbindaz
Жыл бұрын
Why the Dicore vs just taking the automotive paint all the way up?
@alanhat5252
Жыл бұрын
It's elastic enough to cope with the metal expanding & contracting with heat. This particularly shows up along joints & around rivets/fasteners.
@1982MCI
Жыл бұрын
Because Dicor is an actual flexible sealant that will not crack and is designed to prevent water intrusion and paint is a hard protectant for the metal to prevent corrosion only. Two very different products that do completely different functions
@nicholasphillips5406
Жыл бұрын
I had the same question. Mainly wondering why this is not done on normal cars if it’s that important?
@1982MCI
Жыл бұрын
@@nicholasphillips5406 because normal cars are not full of hundreds of holes in their roofs like buses are with rivets stuck through them which offers a negative amount of protection against water intrusion and you are solely relying upon the coating applied to the surface to keep water out and after several years paint on roofs exposed to constant UV rays fades and cracks, especially around rivets and Walla, a leak is born! The other important difference is the fact that most of us are living in buses and not our cars so this isn’t really necessary to help reflect heat away from the the roof which then acts as a radiant heater that the car a/c is designed to overpower and keep the interior at a comfortable temp while your traveling. A bus roof is an enormous area that turns into a huge radiant heater and needs all the help we can give the A/C units to maintain a comfortable environment inside
@nicholasphillips5406
Жыл бұрын
@@1982MCI that was incredibly informative. Thank you!
@TimothyDanielIsaiah
Жыл бұрын
I’ve noticed your back doors and windows several times. Once before on the spray foam insulation video and then here on exterior. On the spray, foam video, you spray foamed the window on the door and on the sides of the door. On this video, I noticed that the back windows and door and windows on the door appear to be painted. Are you replacing the glass with sheet metal or are you just painting over the glass?
@ChuckCassadyYT
Жыл бұрын
It’s sheetmetal
@thetruthserum2816
Жыл бұрын
Video Content Idea: "Crimp Connectors"... Why do mine seem so unreliable? Am I using a bad brand, or technique, crimper, or why are they failing?
@thetruthserum2816
Жыл бұрын
solve: Got a new set of crimpers with removable crimp dies, and it finally works great...
@usdpaulp
Жыл бұрын
How tall is Chuck? I'm guessing 5' 7".
@ChuckCassadyYT
Жыл бұрын
6-1
@wesm3915
Жыл бұрын
What's the length of your bus? What's the name of the color green?
@nicholasphillips5406
Жыл бұрын
Check out his prior video on how he painted the bus
@trailerparkjackson
Жыл бұрын
We need to crowdsource you some knee pads. It hurts mine just watching you crawl around on the metal roof
Пікірлер: 75