Check out www.Laptwo.com for motorcycle, Atv, scooter, and dirt bike parts! One person out of the next 20 orders gets a free 2vintage sweatshirt! Please SUBSCRIBE and LIKE the video if you enjoyed! It helps me out a lot! My Instagram: 2_vintage_ TikTok: 2_vintage_ Thanks for watching and subscribing!
@curtiscaldwell7996
4 жыл бұрын
My warrior is faster.
@Mikey-wf9py
4 жыл бұрын
Wen u drain oil take cap off oil canister/motor
@jeffreymoran6234
4 жыл бұрын
Trust me its never good too wheelie a quad sitting down.
@ryt9845
4 жыл бұрын
Keep the quad
@clappedtater310
4 жыл бұрын
Check the rims they might be bent
@talanrobinson2389
4 жыл бұрын
Put the front end on a jack like your going to take the front wheel off and shake the wheel
@xfiringsquadx
4 жыл бұрын
You are learning all the ins and outs bro. Great job! You should get a low pressure tire gauge for your sport quads. Sport quad tires shouldn't be pumped up any higher than about 6psi. Most manufacture specs are around 3.6-4psi. Especially if you have 6plys on there.
@bloodreno
4 жыл бұрын
I grew up riding this exact quad. Even just the starter sound brings me back. Beautiful to see how you’ve taken care of this 400ex. If you ever want to sell it I would gladly buy it for nostalgia
@Swift-mu8hn
4 жыл бұрын
Try to lean back instead of leaning forward when you wheelie 👍
@claytonstephenson4939
4 жыл бұрын
another awesome video by 2 vintage! [ i usually run my front tires at 4 psi, and rear at 6] but thats also for motocross
@franswa259
4 жыл бұрын
Love the videos Joe. You should absolutely keep that 400ex you wont regret it. Very reliable quad. You already did the top end rebuild, and you got 4 oil filters. I'd keep it for what its worth.
@divergent2619
4 жыл бұрын
gotta jack the front end up and have the tires off the ground to check wheel bearings, ball joints, tie rods.. Same as car/truck...
@carolinabackwoodshillbilly1530
4 жыл бұрын
Good job. Never go wrong keeping that in your collection. I love my 400.
@sojaracing260
4 жыл бұрын
I have a different gauge for my quad tires. A lower reading. Definitely recommend
@landenmurphy916
4 жыл бұрын
It has got to be the front wheel bearings or tie rods or mabey the ball joints
@davidblum_
4 жыл бұрын
Bearings
@reggiexp69
4 жыл бұрын
could be a bearing but often its a tie rod or any of those that can have play on them cause i had bad bearing it still drove straight without a wobble. bent tie rods will make the steering fuked up.
@ricerneon399
4 жыл бұрын
Slow draining no you have to loosen up the fill plug at the top lmfao
@nickshowsstuff435
4 жыл бұрын
I had the same issue with those cheap tire pressure sticks so I upgraded to the tusk gauge and it works pretty good for the money I’d recommend getting one. Tire pressure makes such a big difference. Thanks for the content.
@michaelwalker9842
4 жыл бұрын
i have a 300 honda fourtrax and i just replaced the two front shocks on it last night with some good used ones from another bike but you could see daylight through the holes where the bushings go😂😂 needless to say it rides and handles a lot better now also i recommend lowering your front tires to something like 14 or 15 psi if your ride trails because that's a bit of your suspension and on slick surfaces you won't have as much understeer. love the vids man keep up the awesome work i love your videos whenever i can't be riding
@wildrice5523
4 жыл бұрын
Based on my limited time working on pit crews for a couple of quad race teems in the BITD series, I recommend checking for any play when the front end is off of the ground.. I've dealt with death wobble before, 90% of the time its alignment, the other 10% is typically a combo of worn bearings, bushings, and rod ends. Even down to the lower steering shaft bushing having a crack. Great work though! I really appreciate seeing younger (not that i'm that old) people pick up some basic tools and give it a try to fix things! Keep it up!
@chrisamy5766
4 жыл бұрын
Most common replacement parts on this quad are wheel bearings and axle bearing iv owned mine for 5 years never fails sand gets in there and that's the start of the problem
@DeezGarage
4 жыл бұрын
If u wanna wheelie stop chopping the gas everytime an just hold it and lean back. Back break will always be there to save you.
@joshf8097
4 жыл бұрын
Dang man look at little Chuck. You got to remember, I remember Chuck three years ago, and he was just a little dude. Little guy, skinny as hell. LOL he ain't a little guy no more. Wow your little brothers bigger than you now. God bless you guys. That kids huge now. LOL what a crazy world I'm telling you, it makes me feel older and older and I'm only 31. Absolutely crazy God bless you guys man. That's funny for me because it's I've been subscribed for a few years now and I feel like I've been watching that you and that kid grow up and then he disappeared for a while. Here is now, and he's a grown man. LOL just crazy. That just blew my mind. Lol. Man that kids bigger than me now it's just crazy LOL that is wild. Awesome video buddy I'm glad to see you guys are doing all right you sorry to hear about the wheel wobble that's a real tough thing to get out. God bless
@timwilkinson2797
4 жыл бұрын
I thought that was his son ?? Im i wrong ??
@joshf8097
4 жыл бұрын
@@timwilkinson2797 yeah that's his little brother. LOL hahaha
@motomash6143
4 жыл бұрын
The 400ex is a beast. Good build mate 👍👍
@Ripper-Roo-CB
4 жыл бұрын
This is by far one of the best quad channels on KZitem.
@olliem442
4 жыл бұрын
Don’t lean forward when you wheelie this will help a lot
@superchief5103
4 жыл бұрын
Learning foot brake makes it less scary to go back
@vincentnichols2230
4 жыл бұрын
John Bruzzi I ain’t got back breaks On my 250r
@ryanmichaud4121
4 жыл бұрын
Get comfortable with the quad in the 12 o’clock position
@mikeyplays9436
4 жыл бұрын
THE FRONT TIRES ARE ON BACKWARDS
@yaicandothat5301
4 жыл бұрын
no
@the_2_stroke_wizard903
4 жыл бұрын
Yes
@firstname5418
4 жыл бұрын
This quad needs minimal work. Its a honda and has fresh piston. as long as you regularly change oil, keep the valves and timing in spec that quad will run another 10-15 years before it needs rebuild again
@1991enduro
4 жыл бұрын
Trust me brother i know team red all day
@motomash6143
4 жыл бұрын
Exactly. If you maintain a honda they go forever. This is why I only have honda 👍
@mookieo8094
4 жыл бұрын
Team 4 stroke
@motomash6143
4 жыл бұрын
@@mookieo8094 if its a honda then its all goood 😎🙏
@1991enduro
4 жыл бұрын
Yeh tema 4t too 250r
@nelsonclark5577
4 жыл бұрын
Love the vids man and be safe when riding on the road like that with dirt tiers
@matthewfitzgerald7710
4 жыл бұрын
No doubt things can get sketchy very very fast😂
@FPVSlacker
4 жыл бұрын
Tires are supposed to be 4PSI
@2vintage
4 жыл бұрын
thank you! I will change them to that!
@FPVSlacker
4 жыл бұрын
@@2vintage I bought a 2001 400EX for $1300 and it smoked like a chimney. Bought a 0.020 Wiseco piston and had a machine shop bore the jug. Put on a few other upgrades like nerf bars , new tires, sprockets & chain. It runs awesome. I love the 400EX!!!
@shanemelochick2765
4 жыл бұрын
I was about to say the same thing, my 400 calls for 4-5 psi
@franswa259
4 жыл бұрын
I run my wifes tires at 6psi on the scrambler 500 and it runs like a dream.
@thomashamilton402
4 жыл бұрын
6psi is the magic number for me too
@davidbrilmyer2354
4 жыл бұрын
Little tip brother..I learned wheelies on a 400ex when I was pretty young!!..get used to it get your center of balance and work the sh$t out the back brake and clutch until u get the balance point!!it works promise!!
@sandmanbub
4 жыл бұрын
This may sound weird, but the rear wheels can cause the front to shimmy. I did see a dent in the right rear rim and that could be enough to cause the problem. Probably not the answer, but worth repairing and deducting from the list of possibilities. You'll figure it out.
@kano_.34
4 жыл бұрын
You probably need to put new bearings in, that will help get rid of the wobble, also make sure all your hubs are tight.
@yobro4423
4 жыл бұрын
The reason the tire gauge didnt have a reading is because it isn't a low pressure gauge. You need to have a low pressure gauge for those tires
@Builditathome-Restoration
4 жыл бұрын
Love the 4stroke content!!!! Do a 4stroke dirtbike build from blown to mint condition.
@karl6823
4 жыл бұрын
Joe i just want to say ive watched you for a few years now and i have given you a hard time about alot of your 2 stroke methods, but I honestly mean this when i say you do a great job on 4 stroke motors ive seen you do some nice work from a seized up motor to this this 400ex here nice work joe🤘🤘🤘🤘
@2vintage
4 жыл бұрын
Thank you!
@mrsamick24
4 жыл бұрын
It would drain much quicker if you take off the oil cap🤓
@baikal4784
4 жыл бұрын
Its 2vintage style...... Slow and backwards lol
@drunkonunleaded
4 жыл бұрын
There’s a specific torque rating for the oil filter housing bolts. Don’t over tighten them or you’ll rip the threads right out of the case. Do it every time with a torque wrench to be sure.
@matt12251975
4 жыл бұрын
I'm having 2 stroke withdrawals 🤣😂 great stuff tho. Be careful! Keep the Quad!
@magee16749
4 жыл бұрын
You Gotta get a tire gauge for reading lower psi. And usually good idea to use the psi recommendation on side of tire or on manual. Any thing over 10 pounds Seems like to much
@440commando
4 жыл бұрын
Great video man! Cant wait to see other videos on it
@just_in_time5518
4 жыл бұрын
Nice! Can’t wait to watch in full in a few hours
@murph2521
4 жыл бұрын
Front wheel alignment. Tie string on sprocket and run it around the side wall of the rear tire and up to the front wheels and check ur front that way cheap and easy
@chadriddle3517
4 жыл бұрын
2vintage another good video! I enjoy the 4-stroke quad content! You should find a cheap Honda 450r to fix up too! You would like it they have even more power
@jasonbell4670
4 жыл бұрын
Once you find that balancing point, you'll be able to ride hella wheelies!! You gotta go way further back though. You'll get it! 400ex is a wheelie riding machine
@chadcaudill509
4 жыл бұрын
Great vid of you riding! You need more time on the bikes! Every Sub you have would agree...Btw...your getting alot better on all around fixing them...Every video your doing better on Content!
@brorauntzz2483
4 жыл бұрын
Was reccomended. Glad i found this
@logiescrappychannel8646
4 жыл бұрын
Love you videos I am a huge fan I would probably say I am your biggest fan! and I have been watching your videos for 2 years!!! 🔥
@2vintage
4 жыл бұрын
Thanks for watching man!
@that_crf450r6
4 жыл бұрын
Change your ball joints, tie rods and wheel bearings and it will be fixed for sure
@tylermxmurphy6440
3 жыл бұрын
Not if its got a buckled wheel. If had this problem changed balljoints tie rodend an bearings an was slight buckle in wheel
@samanthaluck8406
4 жыл бұрын
I had the same problem with my quad with the front wheels all you need to do is get to the wheel hubs and tighten the big bolt in the middle of the hub. If this doesn’t work just get new wheel hub bearings
@keva6856
4 жыл бұрын
Nice vid man, keep up good work!
@coyote_450f
4 жыл бұрын
take the dip stick out when draining, it will go faster.
@ChevyGage2002
4 жыл бұрын
Wheel bearings/toe adjustments (wheel alignments)
@greathornedowl3644
Жыл бұрын
Nice job, love the channel, now we are into welding. @19:50 the fawn jumps out - that could have been messy
@jacob.44t95
4 жыл бұрын
That was hilarious 😂 when you went oohooo!
@joenatoli715
4 жыл бұрын
The perks and drawbacks of living in osh kosh W. 😂
@the_2_stroke_wizard903
4 жыл бұрын
The front tires probably have tire slime in them, making them uneven
@sandmanbub
4 жыл бұрын
Got an idea for you. Jack up the front end and use a buffer or some other means to spin each front wheel, one at a time and look for the wobble. Could be caused by the dented rear wheel, but I doubt it. Something in the front is out of balance.
@gtisid
4 жыл бұрын
buckled rim maybe? i’d. be lifting the front off the ground before i started checking stuff. maybe change wheels over left to right and see if that makes any difference
@1991enduro
4 жыл бұрын
It wud be a wheel bearing m8
@gtisid
4 жыл бұрын
Rhys Thomas Ivana missy baby Mia it looked like it i posted right at the start of video thinking he’d just ignore it and say minty again😀
@Obs76
4 жыл бұрын
Nice job! 👍😎👍
@m8fusion712
3 жыл бұрын
Lol that deer just wanted to see the 400ex up close, awesome video man
@xxmonsterxxxd389
4 жыл бұрын
When your checking the oil on that don’t screw the dip stick all the way down your not supposed to
@benny8300
4 жыл бұрын
You know he knows everything lol
@twisted-xh6066
4 жыл бұрын
Ummm...i can't tell. Are you cracking a joke?
@brentpfeiffer4043
4 жыл бұрын
This quad actually has a very complex procedure for properly checking oil level. The factory service manual says. Quad must be started and idled up to temp with zero throttle spiking. For 5 minutes if its above 30 degrees ambient or 10 minutes if its below 30 degrees ambient. You then shut the engine off and unscrew the dip stick and wipe it clean set the stick down on the threads but do not thread it and only at this point have you actually checked the oil properly. 99.9% of people fill them full when its not been warmed up or run at all and they over fill the piss out of them and wonder why.
@jimbob2013
4 жыл бұрын
Can we get a strictly wheelie practice video until your really good that would be a fun series
@2vintage
4 жыл бұрын
I should
@benmcdiarmid2440
4 жыл бұрын
Love the vids bro keep them up
@caseygillis5347
4 жыл бұрын
And on your wheelies don’t pump the gas as much keep a steady throttle
@Chris_123rie
4 жыл бұрын
Great videos man! You should do a subscriber trail ride sometime, im in wisconsin too!
@lazarmrsic5623
4 жыл бұрын
There is also a oil drain under the shifter to drain the oil in the motor and it could be the wheel bearings that the play is coming from
@chrisamy5766
4 жыл бұрын
Mine wobbles from a bent rim but no big deal just gonna send it
@Robbr20
4 жыл бұрын
Tires are on backwards just get a new set bc there spanked I got a lift it up to check the suspension
@2clappedout477
4 жыл бұрын
bro the deer dove out of the way lol!!!
@logansportpilotrp8174
4 жыл бұрын
Check your upper steering post bushings.
@SOUTHEAST_SXS
4 жыл бұрын
4 psi in rear tires and 6psi in the front
@lukecombs5659
4 жыл бұрын
Atv tires are only supposed to have about 5psi not 20 plus and you don’t screw the dipstick in you just set it flush and that’s the correct oil level
@lukecombs5659
4 жыл бұрын
2Stroke Tyson that’s too much air it will just wear your tires out faster from the factory they run 4-5psi that’s what is recommended by the manufacturer
@PopVtecZ
4 жыл бұрын
I never run more than 8 psi on my quad tires. The lower the pressure the more grip and cushion less stress on the suspension
@jasonkoz8985
4 жыл бұрын
I pulled the bolt off the side of the motor there below the two lines that go in and tilt it sideways you get all that out also
@Swift-mu8hn
4 жыл бұрын
When you wheelie try not to lean forward so you can keep it up 👍
@Bandito071
4 жыл бұрын
Loosen the fill plug to make the oil drain faster mate, also your tyre pressures are way too high.
@Pittsburgh-412
4 жыл бұрын
It looks like the front tires are so unbalanced or something to cause all that wobble. I liked your animal adventures too 🤣
@joshbannon8989
4 жыл бұрын
You need a low pressure tire pressure gauge.
@megamind2040
4 жыл бұрын
It's the front barrings going bad making it wobble and also can be bent rims or front hubs
@stevegiroux239
Жыл бұрын
You have one hell of a awesome racing quad cool 😎
@tylerthomas3744
4 жыл бұрын
The tires are off balance and backwards. Looks like the fronts are original to the bike
@wouldyouglowme4235
4 жыл бұрын
Didn’t even know you uploaded today
@brendangamet6534
4 жыл бұрын
How come when he does wheelies he just lets off the throttle
@discipleshadow9496
4 жыл бұрын
your wheel bearings are probably shot, any free play/ movement in them when you rock it side t to side is an indication you need to replace the bearing as that can cause wheel wobble which can eventually lead to some more serious damage later on.
@bradymoeller203
4 жыл бұрын
Nice bicycle grips on that piece 💀
@jerrybernier6046
4 жыл бұрын
No the back ones are supposed to have some push in them if you fill them up to full it will were them out more
@johnreavis9301
4 жыл бұрын
Everybody always runs way to much tire pressure its only suppose to be like 4-6 psi
@kalebjohnson8506
4 жыл бұрын
Hey man just thought I’d tell you my opinion. I recommend not buying parts from amazon. They’re very cheap imo and don’t last very long. Remember this is my opinion and I’m not telling you how to build your machine. I’ve gotten a filter before and when I pulled it out to chsnge after break ride I had shavings in my machine. May be from something else but just a thought. Love your videos just subbed today. Keep making content man! Where ya from? I’m from St. Cloud, MN and ride a 04 400ex. Maybe get a rip if we’re close!
@benny8300
4 жыл бұрын
Add all the oil then run it . You need to read up on how to do oil changes and you don’t screw the dip stick all the way in just put it in until it touches the threads .
@brentpfeiffer4043
4 жыл бұрын
You must not own a 400ex. The oil tank only fits 1.2 quarts before it over flows. The factory service manual says add one quart start the quad so the oil pump can fill the engine and then add the 2nd quart. Dry sump oil system bud.
@BostonBanshee
4 жыл бұрын
Grease the fittings it tightens the joints on the bike it won’t wobble half as much
@zacharykastner9584
4 жыл бұрын
Your left side tire is turned out just steering arms so they are straight that will make it have death wobble
@hayestucker1040
4 жыл бұрын
My first quad with a clutch was a 400ex at 14 😂
@anthonyguerrera6572
4 жыл бұрын
Joe , you need to get a low pressure tire gauge. Your only supposed to run about 5 lbs max in the back. Sheesh 🙄
@shadowbuck1474
4 жыл бұрын
You need do something about the front end the atv shaking like that at high speeds.
@erwinstang70studiosk64
4 жыл бұрын
to much toe in or toe out can some times amplify a slightly loose front end. adjust the toe.
@gragra556
4 жыл бұрын
The 400ex is so quiet that you will be on top of those deer b4 they know it, be careful.
@Quadguy83
4 жыл бұрын
Doubt the tire pressure is making the tire wobble lol
@1011theguy
4 жыл бұрын
i like how you answer your subcribers back
@ZacharyKarmy
4 жыл бұрын
The wheel wobble shouldnt be uneven tire pressure. It shouldnt make that much of a difference. Could be steering stem bearings could be shock bushings. Could be its out of alignment. Thats mainly what would come to my mind when im checking something over.
@nelsonclark5577
4 жыл бұрын
When you do wheelies to get it up a lil easier pop the clutch And it will come up almost every time
@camc7187
4 жыл бұрын
Rear brake so you hold it longer
@luisescamilla5390
4 жыл бұрын
Is it me or are those front tires backwards
@chaselagger6830
4 жыл бұрын
If he replies it will make my day
@2vintage
4 жыл бұрын
Thanks for watching!
@chaselagger6830
4 жыл бұрын
You made my day! Thank you
@gokarting1018
4 жыл бұрын
Nothings as fun as hydroplaning a quad thru a big puddle
Пікірлер: 321