You can learn more about the history of Rimac and the Rimac Tools Big Blue valve spring tester at: bit.ly/3GGAA4z A special thank you to Rimac Tools for partnering with us on this video, but more importantly a special thank you to Rimac Tools for being an essential tool in machine shops like ours around the world since the early days of the industry itself!
@domenicomonteleone3055
2 жыл бұрын
Jim's Automotive Machine Shop Fathet & Son Team amazing work they do in this shop respect back to you 🙏 from 🇨🇦 #YSW where I follow you 💯 from
@juanasanelli6831
2 жыл бұрын
Muchas gracias por el dato de la balanza para resortes Rimac,Lo conocía ,si pero hacía años que no veía uno,hace un tiempo mandé a reparar la tapa de cilindros de un motor Kia de dos ejes de levas, un mierda de motor. El machINE shop, no tenía balanza de resortes,y armó las válvulas y habían resortes vencidos .Tuve que después reemplazar los resortes Con el motor armado.Tremendo trabajo.Se rompió una confianza de más de 30 años.
@shadow83blk
Жыл бұрын
Rimac is proof that if it ain't broke don't fix it.👍
@bigmuz_pilot
Жыл бұрын
I'm going to buy a Rimac based on this video, what a good company!
@wickerman9569
2 жыл бұрын
Man I would be like a kid in a candy store if I had access to the equipment you guys have there. Thanks for taking us a long.
@Sicktrickintuner
2 жыл бұрын
Only takes a bunch of $$
@badrulofficial
2 жыл бұрын
@@Sicktrickintuner in my country will take bunch of $$$$$$$
@bad406camaro
2 жыл бұрын
The cost of new equipment is prohibitive to most. I have recently purchased a used 530 Vanorman surfacing machine for a very low price after researching modern electronics to replace the entirely burnt 1980 circuit boards I was able to restore function and now have a machine with less then 2000$ USD invested that will finish a 45-50 r finish on aluminum. I guess my point is chase your dreams and work with in your budget and you can reach your desires. May not happen as fast as you want but you can make it happen
@altonb93
Жыл бұрын
I’d be buying engine parts just to machine for fun😂
@48statenomad
Жыл бұрын
I'd fuck up EVERYTHING. I can build an engine but to machine anything I'll definitely fuck it up
@stevenbelue5496
2 жыл бұрын
Quality work, those angles is where the powers at, nice job blending and unshrouding. A lot of shops could take a lesson from this bright young man.
@Mr2eyedjack
2 жыл бұрын
Great work, I can appreciate the work and clean shop plus the editing to boot!
@JamiesGarage1
2 жыл бұрын
Love getting new tools! Awesome work as always 👊
@williamharrison54
2 жыл бұрын
Pro tip : magnetize a pocket screw driver, put some lithium grease on the grooves in the valve stem. Use the magenetized pocket screw driver to put the keeper in place. The lithium grease will hold the keeper in place as you slide the pocket screw driver up and off the keeper.
@brustar5152
2 жыл бұрын
That liquid nitrogen process is exactly the process we used at Douglas Aircraft in Malton, Ontario, Canada to install bushings into the globe ends of the DC10 wing spars way back in 1968. We used the power table lift of the mill we used to bore the globe end hole to push the bushings in with the wing mounted on a sine table and held in the air by two gantry cranes, it was a long sucker. That nitrogen process worked like a charm.
@icbtech01
Жыл бұрын
Stuff like that would make for a great video, aircraft shops are awesome places. I remember when the Malton Douglas plant was still in operation.
@gregboggs4721
Жыл бұрын
This was my job when I worked at Hendrick Motorsports. We had a dedicated honing tank. Done everything from installing seats and guides to honing and grinding and finishing and assembling heads. I retired last year but man I really miss doing the work.
@bad406camaro
2 жыл бұрын
Just a note to let you know the content you create is both inspiring and informative. Having been a dealership tech my entire life now in retirement I have revisited machining ( i hated it as a 12 year old being forced to work summers in the old shop) playing with the equipment my grandfather had left me when he passed 30 years ago. When he passed due to monetary and space constraints, I was only able to keep a few pieces. I chose to keep the Sioux seat grinding set the Sioux valve refacing machine a Vanorman 570 and a Vanorman seat and guide machine. All the equipment was stored to the best of my ability over the years. The last few years I have restored all to operating condition. I have also added a 1980 530 Vanorman I got cheap (completely burned obsolete electrical boards) after upgrading to modern vfd it operates perfectly. Thank you for the content and the information you create. It is truly inspirational.
@JAMSIONLINE
2 жыл бұрын
Awesome story! I understand “I hated it as a 12 year old being forced to work summers”… It just didn’t take me as many years to come around to it lol
@ejgrant5191
Жыл бұрын
I know where your coming from...When my buddies Sunnen VGS20 Seat & Guide machine had motor board problems....Sunnen wanted $2000 for a "retro-fit kit" I was able to source a $300 VFD drive and build a control system to get it back in operation 3 days after it went "FUBAR".....The entire cost of our "retro-fit" was under $500....Not every shop can afford a $100K+ CnC block machinig station and sometimes the old school craftsman can create better end result.
@littlejackalo5326
Жыл бұрын
I was the opposite. I loved going to work with my dad. From an 8 year old, to a 12 year old, to building my first house from start to finish when I was 15 (EVERY SINGLE DAY of the summer, every weekend, and every moment I wasn't at school), to becoming VP at 18. Then I decided to go to college to go to med school. Stupid decision. I would have made more money than 99% of doctors make, not had to spend half a million dollars on school, and not have to build a business from the ground up, and not had to have waited 10 years to start making money. Just accounting for the cost of school, and lost wages over a decade, that would have been more money than most doctors make over a lifetime.
@bradhaines3142
Жыл бұрын
@@littlejackalo5326 eh youre talking some pretty shit doctor money
@skylinefever
2 жыл бұрын
Excellent. I'm glad that the damage wasn't deep enough to require welding.
@JohnDoe-ml8ru
2 жыл бұрын
Someone that is actually installing valve guides correctly! Bravo! Very awesome! You also are supposed to install seats like this, prevents them from dropping later.
@upstairs202
Жыл бұрын
In 1973 we rebuilt our first car engine-a 1959MGA. Although it was a comedy of errors, as we had little experience other than single cylinder motorcycle engines, we did prevail. A few years later, I jumped in with both feet in the machining trade. I’ve loved it for the last 41 years. Great job!
@KrautSpaceMagic
2 жыл бұрын
I wanted to say thanks for turning me on to those ez-lok thread inserts, I ended up having an intake manifold come in the day after I watched that video that needed one, it worked perfect and was a fun little project on the Bridgeport
@willyb2412
2 жыл бұрын
I truly enjoy seeing you and your father taking so much pride in your work I bet your customers love you guys
@miceinoz1181
2 жыл бұрын
I have been hanging for ages for a full video like this again. Brilliant work! OK, so how is the new shop coming along? We have not had much update for a long time.
@butchwilson3180
Жыл бұрын
You're very very lucky to have a teacher like your father I learn pretty much everything I've learned by either the School of Hard Knocks but I learned a lot from my elders too!! Really enjoy watching y'alls videos. 100% professional and I love if a job's worth doing it's worth doing right that's my motto too!!
@RCinginSC
2 жыл бұрын
Always enjoy these longer videos. Educational and entertaining 😎👍
@chloehennessey6813
Жыл бұрын
Got my dad one for Fathers Day. Great gift idea!
@Pyle81
2 жыл бұрын
Its good to see that you guys have the ability and the patience to basically nurse these "Well Used" aluminum heads back into service again. A lot of shops would have just said "Save your $$ and put that towards porting a new set of heads and move on. These are toasted " Its scary what there getting for new a new set of QUALITY BBC Aluminum heads today. And thats if you can even find a set. Then comes all the custom work to make them do what you need them to be able to handle. Be it, Natural Asperated, Blower or Turbo (multiple) charged today.
@devscally
Жыл бұрын
Honestly, I'm in awe of the work you guys do. And I can also appreciate the detail you go into when recording the process which I imagine adds aot of time to the job for the benefit of your viewers. I also really like how simple the edits are done. None of that nonsense music, or fancy cuts or forced humour. Just simple detailed capturing of the process. These videos are very 'zen' to me.
@djosbun
2 жыл бұрын
Excellent attention to detail by logging the spring pressure of each valve spring.
@Kevin-wj4ed
Жыл бұрын
Your dad has been a good mentor.
@wilsonrawlin8547
Жыл бұрын
Still watching. and knew Rimac had dropped off the market. Made a lot of money selling used units in the day. They are the best IMO. Totally agree with cross hatch in the guide. Nominal to have a viable surface to carry oil on the wear faces of the guide and valve stem. Nice work and a nice set of CBB heads for the street.
@inscoredbz
Жыл бұрын
That radius cutter to get rid of the ridge in the chamber and around the top cut is pretty dang sweet. Sure beats blending by hand for sure.
@erbenton07
2 жыл бұрын
Forget the valve guides. I want to see a video on how to make that icecream!
@charleshill506
Жыл бұрын
Those heads are a beautiful as any piece of art I've ever seen. (And I was once an art major)
@johnyewtc1
2 жыл бұрын
Would love to see a video update of the block installed back and running again.
@GTFour
2 жыл бұрын
💯
@peterhodgkins6985
Жыл бұрын
I love those crisp seat angles! That right there is some outstanding work. 45 years ago I was shootin' seats with stones. You could get 'em pretty clean but you had to continuously redress the stones. And we never trusted new valves either!
@juancarlosquintana4537
2 жыл бұрын
I have been surprised by the great work you do, happy greetings from tijuana mexico
@bighitstepside
2 жыл бұрын
love your videos, no fluff in a world where most videos are 95% fluff
@MichaelRadelet
2 жыл бұрын
Personally I find a lot of the performance valves are very seldom concentric to the stem, oddly enough the stock replacement stuff tends to be way better, top line stuff for example compared to elgin performance. Good stuff otherwise and always good to do your due diligence and check all these things.
@tedgerstenslager2949
2 жыл бұрын
A ton of stainless valves come from Brazil and Venezuela. QC may not be up to snuff, and collets can be worn out so the valve does not center every time.
@thatruinedmedia6625
2 жыл бұрын
A lot of OTS performance heads aren't as good as people make them out to be. Ive done a lot of Dart LS heads where they were full of chips, had tons of casting flash in the water jackets, and seats with .007" runout and .012" variance in seat depth. To think that most people just bolt stuff like that on is scary lol
@wilsonrawlin8547
Жыл бұрын
Almost like the expect the buyer to end up machining them to fit the valve seats.
@MichaelRadelet
Жыл бұрын
@@wilsonrawlin8547 I see these problems in the “ready to bolt on” heads as well
@wilsonrawlin8547
Жыл бұрын
@@MichaelRadelet IF you've seen this from the people I mentioned that is scary.
@IanB22
Жыл бұрын
Holy god this was a truly thorough thorough - HIGH quality job. I love youtube for recommending your channel.
@jacobthornock317
Жыл бұрын
Knowing a good machine shop and seeing what all is checked and toleranced is worth the price.
@jeffnabors833
11 ай бұрын
I wish I could have worked for your shop. Learning so much. Want more.
@rickintexas1584
Жыл бұрын
That was sweet. Thanks for a great walkthrough of the process. I'm a mechanical engineer. My job is to call out what I want and trust that you guys can deliver.
@cashtalks6253
2 жыл бұрын
If anyone lives in Georgia just remember Goza machine shop in acworth them guys are great!!!
@specforged5651
Жыл бұрын
I would absolutely love to just come hang out here for a day and see all the amazing machinery and talent at work. Luckily being in industrial sales as a part time day job, I do get to see a good bit of this work. I build a lot of forced induction sxs, snowmobile, bike, atv, etc, etc engines, but don’t get to do the machine work, mostly just assembly and porting work. Awesome guys! Love the channel!
@tjzulu1
Жыл бұрын
Excellent video!! Kepp'em comin' brother!!
@glennb2006
2 жыл бұрын
Nice work. Those valve seats are so close together now. Wow!
@robertbradford7892
Жыл бұрын
Attention to detail bar none, love the work great channel.
@eikodunn
Жыл бұрын
I subscribed after watching this video of the valve job on the BBC heads. ⭐️⭐️⭐️⭐️⭐️
@ronhuffman7973
Жыл бұрын
Fun to watch a skilled technician at work! Lots of work.
@randalljames1
2 жыл бұрын
well it is fun to see where technology has gone... When I started doing this kind of work, we had a full set of stones and motors.. best thing that ever happened was single cutter for the entire head side.. Finishing off the radius like you do is arguably the best part of a valve job for most heads
@BrodieBro323
Жыл бұрын
Looks like so much fun working there. Kinda wish I knew how to machine stuff. Should have took machining back in high school.
@johnsonsteve1984
Жыл бұрын
Had to stop the video! That is awesome that you made liquid nitrogen ice cream! Good family owned business fun!
@johnelliott7375
Жыл бұрын
Good for you that remac is helping you out.
@jimc.7121
Жыл бұрын
Outstanding narration! Thank you for all of the information you include in your videos. Very well done!
@raymondj8768
2 жыл бұрын
I Was a dragracer i always reworked a new set of heads there all a mess from mass production . those heads came out fkn sexy bro great job !
@filmaynard
Жыл бұрын
Those valves are huge!
@robertgregilovich2229
2 жыл бұрын
Was a cryogenic fluid production specialist in the US Air Force. Cooled many a can of pop with liquid nitrogen. Liquid oxygen -297 and liquid nitrogen -321. Cool stuff, pun intended.
@localcrew
2 жыл бұрын
Those springs are insane!
@8a41jt
Жыл бұрын
To say that this is impressive is an understatement!
@jimsergi
2 жыл бұрын
fun at work is always a good day
@dekebell3307
Жыл бұрын
Beautiful work fellas!
@jondavidmcnabb
2 жыл бұрын
The liquid Nitrogen was a cool thing for this video.
@alanpecherer5705
Жыл бұрын
You guys are super skilled. A pleasure to watch!
@triggeral
Жыл бұрын
LOVE THIS! Thank you for sharing.
@MrBanacek
Жыл бұрын
Outstanding father/son business. The devil is in the details, and this shop pays close attention to the details. Well done men.
@Formerlywarmer
Жыл бұрын
Best video I’ve seen this week. Cool car stuff with a great family feel. Bless you all MOPAR2YA!
@rodgerq
Жыл бұрын
Beautiful work!!
@Sirmellowman
Жыл бұрын
I personally find a ream and then quick little buff up with the stone is the best way for sizing guides.
@theundergroundlairofthesqu9261
Жыл бұрын
I never would have imagined that valve faces and stems were not concentric!
@Ujeb08
2 жыл бұрын
As a machinist myself for over 35 years, I did a lot of similar work as you showed in the video. I retired 5 years ago and still watch many machining channels on KZitem and I enjoyed your video very much! the only procedure I would question is toward the end when you were using a smart phone to level the head in the machine. Now I love my Iphone and use it for all kinds of things, but I'm sure that it is not accurate enough to use in a machine shop. Get yourself a good tool like a Starrett machinist level.
@JAMSIONLINE
2 жыл бұрын
Thanks! No machine work was being done at that point. Highly uncritical, just needs to be close to level so that when compressing the spring things don’t move on ya. We have plenty of Startett levels and otherwise but there are times when it is critical and times when it is not.
@theondebray
Жыл бұрын
Top quality work.
@danielcarroll5667
Жыл бұрын
"I scream for ice cream !" Thanks for all your great videos............
@fatboysgarage7984
2 жыл бұрын
I'm glad to see a machinists using ear protection. The guys at the local machine shop are in their 20's and 30's and are already going deaf. How anybody can do machine work or mechanic work without hearing protection is beyond me.
@txstang84
Жыл бұрын
Works of art-beautiful job y’all
@billquillin1952
Жыл бұрын
You do excellent work!!!
@augienajera642
Жыл бұрын
Awesome work!!!!
@dangerrangerlstc
2 жыл бұрын
I don't have near the set up you do. Just an old valve grinder, a seat grinder stone setup, and a valve spring tester like you've got. I'm just doing old tractor valves so thats all I need.
@lazarusmunien2087
2 жыл бұрын
excellent workmanship 😊
@pauljanssen7594
2 жыл бұрын
I like using a sharp reamer and then I would Dingle ball the guides for crosshatch for better oiling I used to just shove the guys in the freezer for a couple hours.
@kb9gkc
10 ай бұрын
Well Done!
@PapiKembar
2 жыл бұрын
Good job my friend, i am from Indonesian 😁🙏
@samrodian919
Жыл бұрын
You do very nice work there at Jim's Automotive Machine Shop
@GIGABACHI
2 жыл бұрын
That one Hell of a job you did there. Been a long time since the last time I saw BBC heads look THAT NICE ! 👌😎👍 I always wonder how much of an improvement would be having a DOHC arrangement on one of these Dinosaurs. Something like the QC4V or SB4 Mercury engine.
@davidciesielski8251
Жыл бұрын
Thank you very much, I learned a lot!
@TheTruthBeToId
2 жыл бұрын
That was so good. I was glued like a bug to light.
@jefferybuchan4235
6 ай бұрын
nice job on those heads.
@dadyo63
Жыл бұрын
Well done 😎
@christophercraig289
Жыл бұрын
Nice work!
@MrThunderCunt
Жыл бұрын
You know a tool is reliable when the new one is the same design as the 50+ year old one. Thats some good quality.
@jameshood3692
2 жыл бұрын
man I wish machine shops went the extra mile like you guys, most shops would just cut the seats and be done, wouldn't of cleaned anything up
@scotttipps8155
9 ай бұрын
Tap Magic for the win!!!!!!!
@bobqzzi
Жыл бұрын
Great video. Much appreciated
@bigj231
Жыл бұрын
Turning a lug back dial indicator into a (mostly) flat back indicator is a 2 minute job on a belt sander and even faster on a mill... Going back the other way is the hard part!
@mustang6942
Жыл бұрын
Great job 👍
@daniellecrawford6933
Жыл бұрын
That's got to be the creamiest ice cream you ever ate because the faster you cool the cream the creamier it is
@bigal878
2 жыл бұрын
Great video and attention to detail 👍🏻🇦🇺 I’m guessing those heads are set up to work with a Solid Roller Camshaft?
@cfauvel
Жыл бұрын
HAHA came looking for Soda Blasting painted materials, but stayed for the wonderful video of machining....I love what you guys do. Very informative...thanks
@carmudgeon7478
2 жыл бұрын
Building an engine for the Starfire?😁 I found an old Rimac 500 pounder and a Sun distributer machine in an old abandoned shop in Holcomb, KS. That spring tester hasn't needed any work in 30 years. No wonder they are the standard. They chose wisely who to sponsor.
@JAMSIONLINE
2 жыл бұрын
Haha! That would be a lot of engine for the Skyhawk (same difference). We have the short block built for the Skyhawk but life get's in the way. Thanks for watching 😁
@carmudgeon7478
2 жыл бұрын
I believe the rules dictate Skyhawks require turbo Buicks. 👍
@steveg8337
2 жыл бұрын
Man those seats are close together.
@kennyallison7201
Жыл бұрын
I want a valve job like this in NC!
@kwmiked
Жыл бұрын
Nice work
@av8tore71
Жыл бұрын
Have one but it's not for vehicles, I got it for the valves springs on Lycoming or Continental aircraft engines
@tonycking0121
Жыл бұрын
Great job. A hone will follow a bore. A reamer won't. !
@tedheierman1181
Жыл бұрын
Very informative video. Please keep them coming.
@georgiafan6618
Жыл бұрын
Those valves were close! Is the comp ratio affected at all when you milled the heads on this job? This video was an improvement from others you’ve made. Editing and overall picture was really good. Those heads came out great and it’s evident that your dad taught you well. He passed on his penchant for the details and perfection. Maybe a follow up from customer to see how they fared. 👍
@ladamyre1
6 ай бұрын
Finally I get to see a proper 3 angle seat on a valve job and the guy NOT use lapping compound, taking thousands of miles off the life of the valve.
Пікірлер: 266