Thanks for sharing! Your video on installing a throttle body system is informative. It's great to see step-by-step instructions for this process. Keep it up!
@reco5404
8 жыл бұрын
Installed the kit on my 1987 Jeep YJ 258 Cid engine by my self over a weekend. Very easy simple and straightforward install, had no instructions. They got destroyed during shipping. So I kept this video to refer back to for any questions. Jeep runs like I put a new motor in it, would highly recommend even have a friend looking to make a purchase and I will help install on his jeep. Only thing else I wish came with is a rotor bug for distributor and some sort of universal throttle bracket, for the cost was not too bad. Over all customer service was very good and helpful the owner will talk with you one on one when or if you call. Would recommend!!!!
@fdavidw
9 жыл бұрын
Very informative. It answers a lot of questions I had about TBI.
@garretmos
4 жыл бұрын
Excellent product, easy to install. I just installed on my 2012 Crownline 4.3 Vortec. Straight forward and everything is covered in the instructional video.
@HandMadeWrath
2 жыл бұрын
Why?
@stevejames7335
9 жыл бұрын
Best looking kit ive seen withe a great price point.
@josebeltran702
5 жыл бұрын
Great!!! Video!!!
@bamabrock
9 жыл бұрын
Great video. How about one on your 258 kit.
@davidfink9729
4 жыл бұрын
Cant thankyou enough bud. As soon as there is lite in the morning , I'm gonna go get my truck running
@jimgregory545
8 жыл бұрын
Very interesting !
@jacobjarvis2545
3 жыл бұрын
How well does it run after install and setting adjustment
@joeywalton2248
3 жыл бұрын
Is this the same as affordable fuel injection? If so how hard is it to tune? How is the gas mileage compared to carburetor and how is the quality when driving??? Thank you!
@steffenosbourne7185
9 жыл бұрын
I just received the TBI system from Performance Fuel Injection. I want to upgrade a GM small block in a boat with it. The video answers quiet a lot of my questions, but i got no connector for the temp sensor on the harness?!? i just got a link with 2 loose cables (marked "NEG NO COIL" and "POS NO COIL") that fits to the temp sensor and i don´t know where to wire it... Can somebody tell me? Greetings from Germany, Steffen....
@nolimitballa42
8 жыл бұрын
I'm sure you have it answered but the ECT i believe goes to temp sensor the coil plug goes to the distributor on my set up
@josebeltran702
5 жыл бұрын
How much is this wiring harness? I can’t find it on the site
@Indiancreekgunsmithing
3 жыл бұрын
Give them a call they are great to work with
@stev7ha
4 жыл бұрын
Bought the kit...now car will crank and not start..no spark ...what coil is needed...?
@performancefuelinjection9783
4 жыл бұрын
Make sure that the coil has 12V Ignition power to the positive side of the coil. The pink and white wire from the distributor to the coil does not supply power to the coil that is probably your problem
@gentilejoshsaved1646
5 жыл бұрын
Hello What all comes in kit?
@performancefuelinjection9783
5 жыл бұрын
This is for the Small Block Chevy TBI - Rebuilt 1.750 TBI fuel injection Wiring Harness Check engine light Fuel pump Fuel Pump Block Off Plate Adapter plate - Precision machined aluminum pocket plate Fuel tubes Installation instructions Heated O2 Sensor Map Sensor IAC Sensor (Idle air control motor) New on TBI TPS Sensor Coolant Temperature Sensor Necessary hardware and gaskets to mount system to intake manifold (Please specify what brand Manifold you have) Fuel filter Fuse link Air cleaner stud Small cap distributor - (Large cap available at additional cost) ECM (maybe re-manufactured) with custom calibrated EPROM chip (installed in ECM) Parts not included are: IGNITION COIL FUEL LINES AIR CLEANER
@wingingittracy8508
4 жыл бұрын
Hello sir , I have a 383 SBC, 10.26 compression, AFR as cast heads ,195 intake runners , 76 cc exhaust port, they flow 250 cfm @ 500 lift on the intake, and 186 CFM on the ext a gm hot cam / LT 4 , 279/287; duration at . 050" tappet lift, 525 lift with 1:6 roller rockers , 112 LSA hydraulic roller, edelbrock air gap intake ,1 5/8 headers 2 1/2 ext , th 350 trans 2200 stall 3:42 gears 26 " tall tire, in a 1979 c10 about 3600 lbs should be around 425 HP and 460 torque will this work with my set up ?? dont want to starve it for cfm I was looking at a Holley sniper but love the the idea of easy to get parts
@wingingittracy8508
4 жыл бұрын
I have a set left and right stock 87 truck fuel tanks with baskets for the fuel pump , in tanks pumps seem better then in line pumps, run cooler, less noises, stock pumps are 12 psi I believe .. I am doing a frame off rebuild on the truck I have a lot of money in this truck and want to do it right the first time .
@coreygrimmett3481
3 жыл бұрын
How do I order this kit. I have 1970 elcomino with a 350 I am wanting to convert from carb to tbi
@performancefuelinjection9783
3 жыл бұрын
Go to pfisys.com here is the link pfisys.com/store-3/#!/Complete-TBI-Conversion-Kit-for-Stock-Small-Block-Chevy-350-5-7L/p/41532435/category=27177706
@214mannygarza
6 жыл бұрын
Finally I got my working. I had a bad distributor, now it purrs like a kitten.
@chachisadventures5320
4 жыл бұрын
Do you still sell these?
@ronnyinwaxhaw
4 жыл бұрын
Yes he does. They're off on Friday. My kit came last Friday. I can't wait to install it.
@vinnyboombots8270
7 жыл бұрын
Why do people always call Edelbrock Elderbrock?
@ashlarsen3845
9 жыл бұрын
X2 bamabrock
@214mannygarza
6 жыл бұрын
Can the map sensor be mounted in a 45 degree angle
@214mannygarza
6 жыл бұрын
Hi I bought one of your TBI computer harness from eBay. But I'm having trouble with it to idle, can I still run the computer but use a stock 350 single wire distributor.
@joeblow5511
6 жыл бұрын
214mannygarza theres two types of kits sounds like u bought the one for the small distributor it uses a different coil. the coil u need has 2 plugs 1 from ignition hot and 1 from computer hot. the white wires go to the tach. i just put this kit in an old g body without a problem
@214mannygarza
6 жыл бұрын
Yes everything is hooked up the correct distributor coil lots of new parts . It's just missing and smells like it's running rich. Would I still need to reset my tps since it's all stock ? I put new map sensor new ECM temp sensor, new oxygen sensor I'm just fustrated been having trouble ever since I installed it I'm sure what you sell is great stuff I'm just having trouble with mine. Might buy a new distributor. The wire that we unplug to set the timing on the distributor ... If it's unplugged it runs better ...once hooked up it runs bad . I will just keep messing with it. Thanks for your response.
@joeblow5511
6 жыл бұрын
214mannygarza ur timing is off . sounds crazy i know but the computer needs it to be perfect. I tried to give mine a little advancement but i had the same problem. it runs good with the dist unplugged and terrible with it plugged in. u really should do the timing exactly as the video says no matter how it ran before kit was installed
@performancefuelinjection9783
6 жыл бұрын
No you will have to use the computer controlled distributor
@leroybojangles9272
6 жыл бұрын
Joe Blow what if it runs fine plugged in but won't run at all unplugged?
Пікірлер: 38