💡💡man, awesome tips. Keeping in the axle attached to the hub. That’ll really help a lot next time. It’s the little tips like this that make this channel awesome. Keep it up. 👍🏽👍🏽👍🏽👍🏽👍🏽👍🏽
@JeepSolid
4 жыл бұрын
Cool! Thanks! Glad it helps!
@agnesofglassstudiogalleryl8921
3 жыл бұрын
Thanks for all your jeep knowledge!!I have a 89 yj!
@hayzersolar
Жыл бұрын
i have a 96 xj I'm replacing all front end steering awesome video on ball-joints. now if you are replacing the hubs go ahead and take it off easier to do.
@jackcollins2344
4 жыл бұрын
Thanks Dale, good tip on renting tool.
@JeepSolid
4 жыл бұрын
Yes! Sure saves lots of $$
@gordongman3423
4 жыл бұрын
Excellent tips, thanks Dale. Good idea on renting the ball-joint tool. Like how many ball-joints have I done in my life time.... None. But then again I do own a Jeep. Lol
@JeepSolid
4 жыл бұрын
Thanks! Maybe your's are due to change?
@yanyo999
4 жыл бұрын
Except for tip #2, all this works for a 2WD jeep. Thanks Dale.
@Tracks777
4 жыл бұрын
amazing content
@JeepSolid
4 жыл бұрын
Thanks!
@DaveTurnerBassGuitar
4 жыл бұрын
looks like a good time to change out the u-joints on the hub as well . . .
@JeepSolid
4 жыл бұрын
Yeah. It is
@DJCryptoStix
4 жыл бұрын
I just did my tie rods and I still have a shaking at 45 so I'll do this when I get home. I hope it helps death wobble is shitty
@JeepSolid
4 жыл бұрын
Yeah! Can be tough to chase down the issue..
@DJCryptoStix
4 жыл бұрын
@@JeepSolid I'm a bit bewildered, perhaps I will change out the control arms she does how 305k miles. Thanks for the reply love the content 再见。
@noble2kat142
3 жыл бұрын
Advice for if the ball joint stud keeps spinning? No place to grab onto it without ruining the threads
@thomashensley3319
4 жыл бұрын
Is there a 2nd part showing removal and install of the ball joints?
What is the size of the hammer used to free the wheel hub?
@Dustyfingers
3 күн бұрын
Will this work on a 2001 Jeep tj?
@chrisr6206
18 күн бұрын
How do I know my Ball Joints need replacing? Thanks
@bunnyofdoom87
4 жыл бұрын
This is coming up next for my Jeep! We've been upgrading each suspension component and soon everything will be updated. Trying to do them all before they become real issues. :)
@JeepSolid
4 жыл бұрын
Nice! I'm looking forward to getting my entire front end done. Should drive much better!
@shawnmills8816
4 жыл бұрын
holy crap, the hub nut tip. I've been taking that thing off for years, and as soon as you said you don't have to remove it... a light went off and I felt like an idiot.
@JeepSolid
4 жыл бұрын
I’m glad to help! That’ll make it a lot easier
@Jim_woods
4 жыл бұрын
Good tips
@JeepSolid
4 жыл бұрын
Thank you!!
@emjay4049
4 жыл бұрын
Hey Dale. Completely unrelated to this video. I just got a new to me 95 yj. I am getting a ton of water in my floorboards. Only the front and back. Cannot seem to figure out where my leak is coming from. After a decent rain, it’s basically a puddle on both sides. Any recommendations?
@JeepSolid
4 жыл бұрын
I bet it's coming from outside 😀 hehe.. I crack myself up. When mine did that it was because the cowl vent drain was plugged. Have you checked that?
@emjay4049
4 жыл бұрын
Haha. I have. Doesn’t seem to be the problem.
@KingKoudi
4 жыл бұрын
I love this cata
@JeepSolid
4 жыл бұрын
Thanks!
@priceisright7751
3 жыл бұрын
I appreciate your intelligence!
@slim3d
4 жыл бұрын
Hey Dale, what camera do you use, and do you edit your own videos?
@JeepSolid
4 жыл бұрын
Yes! I edit my own. I’ll get you you a link to my camera
@QUICKSILENTSCOPE
4 жыл бұрын
@@JeepSolid hey Dale i'm curious on the camera too!
@JeepSolid
4 жыл бұрын
I've filmed with a few different cameras over the years, and this one is my favorite so far!! Good quality and not too bulky for those tight places. Here's the link amzn.to/32CeGv7
@BlueGheenoe007
2 жыл бұрын
Hay y don't u use a pickle fork to remove ball joint
@rushwal
4 жыл бұрын
It *can* be done with the O'Reilly's kit... But I wouldn't suggest it. Ask me how I know.
@JeepSolid
4 жыл бұрын
Haha! Dang, but I'm impressed! Must have been a pain.
@St.Hermans_Speed_Shop
3 жыл бұрын
Put the ball joints in the freezer for as long as you can before install. They will just about fall right in.
@slim3d
4 жыл бұрын
Still need one of those hats!!!
@JeepSolid
4 жыл бұрын
Soon.. very soon.. I’m working with a vender now. Trying to get the design right.
@igotstaknow
4 жыл бұрын
Next time leave out the annoying mall music.
@JeepSolid
4 жыл бұрын
Music depends on my mood when I'm editing. Apparently I was in the mood for mall music. Lol 😂
Пікірлер: 49