Fabulous lecture. One of the best(probably the best) lectures on stainless steel welding for beginners/novices. Thank you
@Mike_Laird
4 жыл бұрын
Chris is the MAN!!!!!!
@stevenmcc6052
3 жыл бұрын
Chris. Best stainless vid on the tube.
@GoalOrientedLifting
3 жыл бұрын
Thank you! This have been the most helpful video I've seen so far, in Tig welding.
@ol-man-duffyj688
3 ай бұрын
Thanks Chris you helped me way more than the bigger vids out there just saying to stop adding heat. Thanks for the arc length explanation and showing how to set up a gas lens attachment and #12 cup. Bug help.
@phatpizza610
4 жыл бұрын
Finally someone that shows me some things to check as to why I’m getting the grey, was confusing me as it was only happening when using filler wire, guess was prob a combination of a few things
@phernayes
3 жыл бұрын
Super clear! Thanks a lot!!!
@22strokes
4 жыл бұрын
Great! I learned something today thanks to you! I definitely need to keep my arc length shorter
@burrowssj
4 жыл бұрын
Thanks for this video, wish I'd seen this sooner
@radishfever
4 жыл бұрын
Good explanation.
@MrRippsalot
4 жыл бұрын
I always run a gas lens. And go higher amps than i need with foot pedal variance to control my heat.
@mikemattera9513
4 жыл бұрын
I would have like to seen the back side of the last weld.
@CucoGT2s
4 жыл бұрын
Hi Chris is Cuco996 Congratulations now you’re sharing knowledge good to learn from a celebrity. Yesterday I bought my first Tig 😎😎😎
@danl.4743
4 жыл бұрын
What movies is he in?
@everlastgenerator
4 жыл бұрын
Congrats on your first TIG
@milesmoore5422
3 жыл бұрын
What was your stick out length ? Can you show some gas lens profile shots of you running at .01 to .02 arch length ? What was your CFH ? Pre-flow ? Post-flow ? What is the best grind for this weld metal thickness ?
@wild12valve
4 жыл бұрын
What about gas flow vs cup size, etc?
@idriwzrd
4 жыл бұрын
So you use both insulators with a gas lens? Where'd you find this guy, Everlast?
@ypaulbrown
2 жыл бұрын
ye yes yes...great stuff
@randalnannie991
Жыл бұрын
High freq tig For initial arc...correct Not continuous
@harleyjune1233
4 жыл бұрын
would tig Al benefit with gas as well?
@eveliomiguel8052
4 жыл бұрын
Thanks for adding subs in Spanish
@robertferrara4529
4 жыл бұрын
thank you
@buyafaruk2435
3 жыл бұрын
Hope it is useful
@JulioArioRayon
2 жыл бұрын
Excelente
@tigmigevgeniilysenko
4 жыл бұрын
These are the ones who come to me, bring in drops, and they can’t stably hold the additive in the weld pool.
@luisalbertobohorquez1900
4 жыл бұрын
Deben hacer la traducción en español , en la parte inferior.
@indraverboden6256
3 жыл бұрын
👍👍👍👍👍👍.mantap
@ng4410
4 жыл бұрын
hello am in Australia.. Have a job that has a lot of steel flooring around job site. Laydown of electode a pain. Using a modern small inverter stick welder. Q) anywhere in USA / your company sell a stick electrode holder with ON OFF switch. ? Have never seem one. Only one on www is one for 12 v vehicle welders it seems. Seems a no brainer to have the option? any info appreciated. Has to deal with wide range amps no doubt.
@TheMasterizzatore
2 жыл бұрын
Why would you Need a switch for Stick welding?
@a.bakker64
4 жыл бұрын
Hi Chris, is the Lightning 225 available in Europe? Finland/Estonia?
@ronniehaycraft4052
4 жыл бұрын
I'm pretty sure these everlast machines are the same as r tech which is available in the UK
@everlastgenerator
4 жыл бұрын
@@ronniehaycraft4052 They are not the same. They have the same case, but the internals are VERY different.
@a.bakker64
4 жыл бұрын
@everlast welders is the lightning 225 available in Europe, and if so, can you give me an adress?
@everlastgenerator
4 жыл бұрын
@@a.bakker64 Not yet, but soon.
@billsimpson2392
4 жыл бұрын
👍
@_hector__
4 ай бұрын
"A good arc length is between 10-20 thousands of an inch" What? This is ridiculous 10 thousands is 0.254mm
Пікірлер: 38