thanks for the tips. Much appreciated. The 1198 will sit nice and will have a wire loom too. thanks again.
@GenericUserUnknown
11 жыл бұрын
Fantastic video. Thanks for creating it.
@DougVahrenberg
11 жыл бұрын
There is no internal SI transducer on the Trolling Motor since it must shot out the sides. I've run it for many years externally with the Transducer Shield and Saver and works awesome and have had zero issues.
@jaimeastin
6 жыл бұрын
very good advice! even video and explanation. thank you for sharing.
@DougVahrenberg
11 жыл бұрын
Call Transducer Shield and Saver I think they may be stocking it now. I got a roll thru T&H Marine.
@blackknife1
10 жыл бұрын
@ Johnny, that rubber pad you're referring to is actually an anti-slip pad with kind of a sand paper finish. The are stock equipment on Skeeter boats, and actually say "Skeeter" on them. You could buy something similar from Home Depot. They sell anti-slip pads for floors & stairs. Just cut it to the shape you want and peel off the self-stick backing www.downwindmarine.com/Beckson-Step-Mate-Non-Skid-Step-Pads-p-91001365.html
@tommyliu4683
9 жыл бұрын
Very NIce.. thanks for the VIdeo very helpful!
@Cornuts1000
12 жыл бұрын
Is the tranducer tthe same as the tranducer used for the 596c HDDI model? Wish you would have shown how to actually wire the unit to the wiring in the boat for us Unelectrical guys.
@nikkygonz
11 жыл бұрын
Hey Doug, I have being looking for the wires sleeve material that you have in your wires but I'm having a hard time to find them; Could you tell me where I can go and purchase one? On what Auto parts?
@JohnnyJenkins
13 жыл бұрын
Did you install that rubber pad for Bow Humminbird reciever or did the boat come with that?
@tlalexander3
5 жыл бұрын
I have an 1198 humminbird I just bought and I need to install the heading sensor. I watched your video about using a compass for electrical interference. However on one of your videos your heading sensor has an arrow, but mine does not. So how do I know which way I should mount it so it is pointing the correct way? I guess I could use the compass, but I still need to buy a cheap one. I was messing around with it today, and the way I aligned it was drastically different than what my phone said. Granted either one could be off though
@DougVahrenberg
5 жыл бұрын
If it does not have the Arrow at no speed you are not using the Heading Sensor or have not selected that as the GPS Receiver. Need to make sure you have GPS-HS receiver seleted in setup tab
@williamjohannes9104
12 жыл бұрын
Where can I buy the mount? This seems to be just what I need
@natebraack7704
11 жыл бұрын
Is there any way to run the wires of my new 1198 transducer through the inside of the fortrex minn kota? I don'e like the wires being on the side like that. I have the transducer build in now. that I will not use any more. I'm getting the 360 very soon. I have the two 1198 ethernet together should I just not worry about the transducer on the trolling motor?
@TheBMWBUM
9 жыл бұрын
If you're concerned about electrical noise running transducer wire along the TM wire/cable bundle... why do you have the TM power wires forming a winding physically around said wire bundle? I'd be worried about winding wire around wire like that creating any weird field effects.
@DougVahrenberg
9 жыл бұрын
It never bother the transducer side because I try to keep the two systems away from each other.
@tcbridges
7 жыл бұрын
Doug, can you tell ne which ram mount you showed there. I need that exact same one. Thanks, Tom
@DougVahrenberg
7 жыл бұрын
I do not remember which mount that was. Been several years. I use the T-H Marine Kong mounts now. Much more durable.
@tcbridges
7 жыл бұрын
Doesn't that Minn Kota Fortrex have a transducer built in it so that you can just hook it to the Ethernet box?
@DougVahrenberg
7 жыл бұрын
All transducers must go through the unit they do not connect to Ethernet switch.
@edmacey9715
7 жыл бұрын
HI DOUG, Does the us/2 run through the shaft and down the steering cable ? and does that create interference with the 2d,if not why can't i run the wire on the outside of the steering cable
@DougVahrenberg
7 жыл бұрын
Yes Universal Sonar does run through the shaft and steering cables. If the connects are good and tight I have seen very little conflict or RF Noise with US. I'm using it currently on my HELIX 12 G2 with the 360 and works fine.
@wjvogl
10 жыл бұрын
What Hummingbird Model and Ram Mount model or ball size is in this video?
@DougVahrenberg
10 жыл бұрын
That was a 998c.
@wjvogl
10 жыл бұрын
Doug Vahrenberg Thanks Doug. I will be mounting the same on the bow of my boat within the next couple of weeks. I may be back with more questions. Thanks again.
@DougVahrenberg
11 жыл бұрын
transducershieldandsaver{dot}com is where you can get the mount
@williamjohannes9104
12 жыл бұрын
Where can I buy the mount? This seems to be just what I need
Пікірлер: 27