I reckon it would be a good idea to make sure that the parking brake is on, it’s in gear and in 4WD mode with locked diffs. That way there’s less chance of the truck moving whilst you’re working on it.
@theageoftheawakening4806
2 жыл бұрын
Don't unimogs have air compressors? I'd just have a pneumatic jack and impact gun
@TomSilver_42
Жыл бұрын
Rattlegun is a good idea .. just, why battery powered electric one, when you have an air lines cross the whole truck, so why not air-powered rattlegun? Yes, you'll need some air hoses, but unless you do have CTIF you should have at least one airhose to inflate/deflate your tires. And with CTIF you might be able to simply use that connection point right on tire with some short airhose.
@unidanengineering
Жыл бұрын
Unfortunately the air tanks and air system on the truck are not sufficient to run an air-operated rattle gun so you would get a few good seconds of us and then the tank would need to refill with air. Unless of course you had a PTO or hydraulic driven compressor for this which would be a very expensive way to tighten wheel nuts.
@TomSilver_42
Жыл бұрын
@@unidanengineering Thanks, I guess you are the experts here and so you tried and failed onboard air powered rattle gun. Good point. Thanks for insight!
@htchobbytechniccreative8438
2 жыл бұрын
How replace plate cover handel tranmisi?🙏 I want video. tank you
@andersjonsson7218
2 жыл бұрын
Exellent demo, thanks!
@edwardcarberry1095
17 күн бұрын
With my tires once the nuts are loose, I use the 1/2" ratchet to undo them. Or the 3/8" as that is easier to move then the larger flex bar.
@garyfindlay5503
2 жыл бұрын
Thankyou for the demo. It is also a good idea to check the wheel nuts again after about 50 Ks as the rim settles back in you can find that some of the nuts will have come loose. Personal experience.
@unidanengineering
2 жыл бұрын
Yes, great point! After all servicing etc. we put a reminder on our customers dashboard to do this.
@agussiswanto6076
2 ай бұрын
Amazing demo, thank's 4 u trik👍👍
@Dags470
2 жыл бұрын
I carry my 18v rattle gun and a torque wrench. I would probably die undoing all the nuts by hand. 🤣
@theageoftheawakening4806
2 жыл бұрын
How can't u find a place to put chocks?
@Dags470
2 жыл бұрын
I also carry 3 of the original nuts to centralise the wheel because the new nuts aren't bevelled.
@simonbar7665
Жыл бұрын
Big like
@koosok13
Жыл бұрын
Good job 👌
@matpoire
Ай бұрын
What was the tire size ? Thanks
@MogsAndDogs
2 жыл бұрын
Thanks! Quite clear.
@philhealey449
2 жыл бұрын
A close up picture or view of where the jack was placed on the axle would be helpful; presumably this is best near to the spring mounting to reduce the lifting force needed and minimize risk of damage to the axle casing. Unicat has a helpful video I think on dismantling the Hutchinson rims.
@GaryTischer
2 жыл бұрын
Photo at 2:54 shows it pretty well Phil.
@andrefischer5025
2 жыл бұрын
Which way do you rotate the tyres? Do you include the spare?
@michaelguerin56
2 жыл бұрын
The fun part of rotating Unimog tyres, if you have the factory standard Michelin directional tyres, is that: you have to take some of those tyres off the rims, turn them over and put them back on. It is a job best done with the appropriate workshop tool, as seen in your local tyre shop. 🙂 We did it at the main camp motor pool. Those non-directional tyres will make life a great deal easier.
Пікірлер: 24