This video may seem silly to some, but if you have never operated a CNC... It's super helpful
@PrincessAnnabellzDad
3 күн бұрын
If this is the level you're at, you're nowhere near ready to even look at a cnc machine.
@phillhuddleston9445
2 ай бұрын
Good tutorial for beginners but with ER collets the flange that locks them in is eccentric so you should insert the collet into the holder at an angle where the flange is hooked under the groove and rotate it to align with the holder while pushing foreword, in sot sure how to do this just wiggle around while pushing but do this without a tool in it and until it snaps or locks into place. This is especially important on the larger er collets. When using a weldon type holder that requires a flat milled on an endmill be sure to tighten the set screw into the slot or flat then back it out just enough to slide up and down, if it does not hit both ends of the notch and is not captive you did not get it into the notch created by the flat and need to adjust it until you find it then tighten it tight. I think you may have gone overboard with the gloves used to hold an endmill or any tool, yes you need to be careful but if you are that sensitive then you should never touch a part because they often have sharp burrs and are covered in sharp chips that become splinters easily. In the real world you won't make it if you need a glove to handle a tool, I have had several cuts and numerous splinters over the last 30 plus years in machine shops, one of those times I was wearing thick leather gloves, I thought they would protect my hands but trying to pull stringy chips out of a conveyor proved them to be ineffective, better to rely on common sense. My advise is use common sense, learn from your mistakes and have a good pair of sharp tweezers and regular ones for the splinters sticking out of your skin. You don't have to be tough but it helps to not be a pussy either when working in a machine shop.
@JohnFuller804
2 ай бұрын
Thanks, This video is intended for high school students. I can't have students getting cut in my classroom hence the reason I advise they wear gloves.
@abrhammulatu1393
Жыл бұрын
This was very helpful John. Thank you!
@andyvan5692
Жыл бұрын
great beginner video, but for torquing those collet nuts, use the other holder, vertical one, that way the fixture holds the tool, then hold the torque wrench with BOTH hands, this ensures an accurate reading, and that the force doesn't send the end flying as the head slips off, with nothing to catch it.
@CAD4UNIVERSE
3 жыл бұрын
Excellent!!
@gautamsharma4515
2 жыл бұрын
You said you set the torque wrench to 34 Lbft. Have you accounted for extra torque to be generated due to extended certerline while attaching the crowfoot to the torque wrench ? If not, then there would be variations in torque values that is transmitted into the collect nut and risk of damaging the thread or nut due to over torque.
@cheizaguirre5494
2 жыл бұрын
Great info ! What is the correct lbft?
@smo3241
2 жыл бұрын
I have a problem: when I'm milling the part one time I get one size, and when I get the toolholder from the spindle and get it back to the spindle and milling another part I get another size. It varies from 0.02 to the 0.05 mm. What can be the reason of this problem?
@Schooloutdoors
2 ай бұрын
Old machines tend to do this because of wear on the machine. Also this can be from the spindle warming up and cooling down
@ewildgoose
2 жыл бұрын
I think you need to have the crow foot at 90 degrees to the torque wrench body? Otherwise your wrench length isn't accurate and your torque value will be off?
@darrenconway8117
9 ай бұрын
I noticed the same thing. The applied torque will be greater than the indicated torque.
@tegheim
2 ай бұрын
Correct. 90° it is 👍
@dcocz3908
Жыл бұрын
What is the name of the tool holder jig you are showing?
@JohnFuller804
Жыл бұрын
I don't know where our school purchased them from
@abhayakumargouda4144
2 жыл бұрын
What is the name of this part..where you clamp ur tool holder for change tool?
@JohnFuller804
2 жыл бұрын
Tool holder fixture
@sagarpathak6568
2 жыл бұрын
Tool holder its also setup in tool room
@hussainm.k9808
Жыл бұрын
Its BT40 Locking device We have same in ready stock
@Pfiffikus25
2 жыл бұрын
At 6 min, you didn’t lower the tool far enough to engage into the groove!
@JohnFuller804
2 жыл бұрын
It's engaged, depth perception can be deceiving.
@phillhuddleston9445
2 ай бұрын
I think you are correct, he needs to double check it by loosening it slightly and moving it up and down, if it's not captive it's not in the notch.
Пікірлер: 23