I ordered a 10 pack of cat7 shielded field connectors and a 250' roll of cat8 cable and sat down after watching this video a couple of times. They look exactly like and, go together the same way. I made 5 cables varying in length to upgrade from cat5 cables that were cheap and poorly manufactured. My new spool of network cable was manufactured in Taiwan! Thanks for the assembly video, it was a great way to see how they go together since there were no instructions or any info of any kind!
@dred05m61
11 ай бұрын
Very good professional video 🖥 The comfort of using this toolless RJ45 is by a factor of 1.000 over crimping.
@DaBuzz92
2 жыл бұрын
This connector is SUPER amazing! Saved my ass during work at least 1000 times. Worth any money 💣💣
@Mrbobinge
2 жыл бұрын
Simple concise instructions showing important details. Exactly what I needed. Thanks for posting.
@ShenzhenAngnetTechnologyCoLtd
2 жыл бұрын
Can you send your address to my email,jack@szangnet.com
@Gabriel-ju5nq
2 жыл бұрын
Great video, really clear, really easy, really useful
@idanuzan2311
4 ай бұрын
Thank you , your video helped me!
@ShimonKupferman
4 жыл бұрын
Beautiful! And you also get a strong metal connection bonus.
@Lineage_2
Жыл бұрын
Why didn't the G light come on?
@techflipswitch5937
Ай бұрын
It's ground and meant to turn on if you have a shielded cable (stp)
@darek7232
6 ай бұрын
Dzięki 👍
@ShenzhenAngnetTechnologyCoLtd
6 ай бұрын
Can contact our factory if you are interested in our products😀
@razvanon
2 жыл бұрын
is this type of connecton just as good as a standard one that is crimped ?
@cenchloraadums3143
Жыл бұрын
No, it's not. It doesn't make a solid connection. You'll experience connectivity issues later.
@TaiLe-dr5ve
2 жыл бұрын
You make wrong connection, missing connect GND for two ends, the tester showed it.
@ShenzhenAngnetTechnologyCoLtd
2 жыл бұрын
the white connector was UTP connector,so the tester did't show the GND signal. Thanks your comment.
@alienwolfx3758
2 жыл бұрын
Is this connector reusable?
@ShenzhenAngnetTechnologyCoLtd
2 жыл бұрын
yes
@cenchloraadums3143
Жыл бұрын
No
@rgmatta3524
3 жыл бұрын
Where to purchase in USA?
@mickclarke2088
2 жыл бұрын
Got similar from Amazon UK, so I would say you can get them from your Amazon, I just searched toolless rj45 connecters
@hippiechicks9918
2 жыл бұрын
where can i buy them
@ShenzhenAngnetTechnologyCoLtd
2 жыл бұрын
You can send your request to jack@szangnet.com.thanks
@maestroboy
Жыл бұрын
I see 3 tools in this video..
@disdonc6012
2 жыл бұрын
How to destroy some scissors by cutting wires ;-)
@mickclarke2088
2 жыл бұрын
These wires are so thin there not going do damage scissors unless there the cheap ones you get for around 50p
@disdonc6012
2 жыл бұрын
@@mickclarke2088 I think it's not the thickness but the material. Cutting metal with scissors which are made for cutting paper or only fabric will always leave small traces. If you do this once or twice there might not be any noticeable effect, that's true, but it's still a degradation over time.
@cenchloraadums3143
Жыл бұрын
@@disdonc6012 Doesn't matter, you can always buy a new pair of cheap scissors. But using a dedicated wire cutting tool is the professional method.
@SianaGearz
Жыл бұрын
The most common Ethernet cable type is copper coated aluminium. It shears at the soft inner core and cuts with very little force. Better and less common is pure copper Ethernet cable, which is harder to cut, but even copper vs. steel of the scissors (typically plain stainless), steel wins easily due to a lot more hardness, no substantial damage to scissors. You'd have to go through thousands of these wires before you find any wear on the scissors. And yes thickness makes a difference, upon it depends the force with which the conductor pushes back on the blade. For example flush cutter for fine electronics use made from surgical stainless is rated to 1mm thick mild steel (not hardened) or 1.6mm thick copper, because copper is that much more pliable and easier to cut, and it would cut thicker aluminium yet. Obviously you don't cut hardened steel or stainless steel with this tool, since the tool doesn't have enough extra hardness above the material you're cutting and will likely take some damage at any thickness, you'd need to get extra hard tool steel version of the tool instead.
@disdonc6012
Жыл бұрын
@@cenchloraadums3143 I don't want cheap throw-away scissors for cutting fabric. Even when new they are shit.
Пікірлер: 34