HANDS DOWN, BEST T-CHAIN TUTORIAL FOR THIS ENGINE.
@sonlightcommunitychurch5287
Жыл бұрын
Your three words saved me from a headache. My first time timing and I got it right. Thanks
@michaeljones-cy2oe
9 ай бұрын
You guys are awesome and I did buy the kit for the 2013 Toyota Camry 2.5 from Cloyes. Please keep the videos coming. Turned a lot of my customers onto you guys.
@kellyclibern9042
2 жыл бұрын
Couldn't ask for a better how to video.
@Gpsautomotive
Жыл бұрын
Best video on KZitem for this job. 👌
@FishingwithTarzan
2 жыл бұрын
Just Wana say thank you all data for som reason does not show certain timing procedures for vehicles only conplete overhauls these videos are som informative and helpful you can literally take these steo by step if need be even you guys are awesome !!
@pedrosanchez2230
5 ай бұрын
VERY EXCELLENT EXPLANATION
@marcokawar5459
2 жыл бұрын
These videos are awesome! Hope you keep uploading more
@shawnacano182
2 жыл бұрын
Thank You i been look for this video for years I'm upset this is my first time seeing it. i have pull my motor out three to connect the time cause of a crankshaft p s batch B, so a inline 4 only has 1 Batch A. still have the problem but car runs great. just will not pass cause if check light on. this is the best ar-2 video yea.
@Usmanthemecano
3 жыл бұрын
Seems pretty straightforward
@brettgooseauto4390
8 ай бұрын
AllData did not have instructions... thanks
@odishoodisho4904
3 жыл бұрын
Great as always thanks for sharing your knowledge
@hoobered1232
Жыл бұрын
great video. Can anyone confirm the parts quality compared to Toyota OEM parts?
@mrlover013070
3 жыл бұрын
Thanks, like always very helpful.
@user-eo9zm4eq5j
10 ай бұрын
I’ve installed both vvt sprockets chain kit. After finishing I now have a p0017 code. Before I had a p0016 code. I removed valve cover recheck marks. All marks line up. ?
@Silveradokev
7 ай бұрын
What did cloyes do to help with the intake cam phaser problem that these engine have , in developing a cold start rattle due to the lock in the phaser getting stuck ?
@luissantiago147
Жыл бұрын
Great Video!
@OverlandOrange
2 ай бұрын
Does motor need to be removed to perform this?
@jonathanbrand1270
Жыл бұрын
Awesome video
@rustbucket77
Жыл бұрын
Can both phasers be replaced with the camshaft still mounted on the head? I was told that the exhaust camshaft has to be taken out.
@arthurmiller8336
2 жыл бұрын
Thank you great tips I like it
@ralo20072007
2 жыл бұрын
Can the timing chain tensioner be replaced by taking that square cover off? Without the need to replace all other components or taking the whole cover off?
@peytonsilver5817
Жыл бұрын
Yes it can. It’s a pain though
@kellyclibern9042
2 жыл бұрын
Other than cylinder displacement, is there any other differences between the 2.5 and the 2.7? Could I put a 2013 2.5 in my 2013 Venza? It has a 2.7 currently. At a glance, they look identical?
@gunnarmode
3 ай бұрын
Great video just did that
@accountingtax3417
Жыл бұрын
Hi Cody, what is the bolt size for the timing cover plate that gives access to the intake vvti sprocket and what the size of the bolt that hold the intake vvti sprocket in place. Thanks a lot!
@singhsarabjit
Жыл бұрын
Hello Sir, Thank you very much for this video. I followed steps, Put chain on all the timing marks. But when I turn engine by hand, yes I turned engine 5-6 times but still chain marked links are matching, did I do something wrong? engine run fine after I put back together but it does through code P0017. Please advice. Thank you very much!!!
@samisolissolis6556
Жыл бұрын
Thanks
@BennyTheButcher2
3 жыл бұрын
Just curious. Is this an engine-out or engine-in service? Guessing engine-in, as everything is accessed in the front
@JL4ever
3 жыл бұрын
Can easily be done engine in
@onebreath210
8 ай бұрын
I'm not sure if I'll get a response to this question or not, but I thought I'd try anyway. So you say if the timing cover is off and you replace everything (chain, guides, tensioner, and phashers (vvat-i gears) the phaser/vvt-i gears DO NOT need to be unlocked when installing the new part? So I'm taking that as if you are not removing the chain, just the phaser, that's when it needs to be unlocked for install?
@Cloyes01
8 ай бұрын
As long as you hold the camshaft while tightening the phaser bolt, you do not need to unlock the phaser. The only way you could damage the phaser is if you tighten the phaser bolt while using the chain or another shaft to keep the phaser from turning. That would put pressure on the internal locking pin.
@onebreath210
8 ай бұрын
@Cloyes01 good to know! Thank you for the reply
@jhnmwaniki
2 жыл бұрын
Can you please do a video on 2.7 ar engine full rebuild
@korno5718
3 жыл бұрын
I like it
@pauca2014
3 жыл бұрын
What are the cost of a chain replacement? I have a highlander base 2006 4 cyl.
@timocrosby
3 жыл бұрын
I got it all installed and the car runs like new. Thanks for the video!
@chucke3305
2 жыл бұрын
@@timocrosby how much they charge you?
@cesarbriones2419
Жыл бұрын
Love it
@derakbell8143
2 жыл бұрын
Man I really wish you would have showed where you put sealant on the front cover and what type. Tensioner bolt torque value? This crazy easy and plan on doing this on my camry this winter. 2011 2.5. Has currently 214,627 miles on it. Im doing both cam phasers as well.
@RAMJO
2 жыл бұрын
Hi derak, is their reason why you decided to do this my 2011 Camry has 120,000 miles. Little rattling noise started a couples months ago, but now it’s got to the point that when engine is hot and I try to turn on the car it takes a couple seconds. I turn the key and it sounds like it’s gonna shut off. I hear the crackling noise then it’s stops. When driving it runs fine no problems at all.
@enriquesilva8952
3 жыл бұрын
I like the video gracias
@loganburnett677
2 жыл бұрын
If there is damage to the crank reluctor wheel you can’t just replace it you have to replace the entire crankshaft or am I missing something?
@lt1swapgonzalezperez102
Жыл бұрын
That's what I'm trying to figure out I can't find anything online I'm trying to buy the reluctor wheel but can't find anything I'm guessing it comes complete with the crankshaft
@orpiv
2 жыл бұрын
I have a noisy 2009 Toyota Venza especially on cold start .. Is this the same kit and install?
@Cloyes01
2 жыл бұрын
Yes, if it has the 2.7L.
@2daybmine
Жыл бұрын
where is the video for the 2.7 3ZR. There are 2 chain to change and no video for guidance.
@chalinoahuesoduro5566
3 жыл бұрын
Whats tge torque on the tensioner bolts?
@adilabilbekuly
2 жыл бұрын
Hi! Is it possible to replace only tensioner without opening top cover cap just by opening small cap in front side of engine?
@Cloyes01
2 жыл бұрын
If you remove the tensioner cap you will need to remove the tensioner and deactivate it. Upon reinstallation, the valve cover will need to be removed to activate the tensioner against the chain.
@ralo20072007
2 жыл бұрын
@@Cloyes01 I've heard you can just rotate the crankshaft from outside until you hear a few clicks indicating the tensioners been activated. Will this method work?
@wilsonharlot4435
2 жыл бұрын
If this same engine (Toyota venza 2ARZ) has knocking sound, once steam for 30mins time, what is it remedy
@writeupking
6 ай бұрын
Engine replacement 👀.
@Andy-ue3dv
3 жыл бұрын
So if only replacing chain/guides/tensioner, and reusing camshaft gears - Do we need to “advance” the intake camshaft gear like the FSM states?
@Cloyes01
3 жыл бұрын
If you are not removing the phasers there is no need to follow the phaser unlocking/advancing procedure that Toyota recommends. That procedure insures that you don't load the phaser's internal locking pin while torqueing the attachment bolt.
@chukwumaedwin5484
3 жыл бұрын
I changed my top gasket after changing the top gasket the engine started making noise rock rock rock rock rock rock
@nathanstander1493
Ай бұрын
That crank pulley looked more like 11 o'clock, but I guess pointed up in general?
@Cloyes01
Ай бұрын
Correct. The main focus is making sure the marks align. You can make small adjustments to the shafts if needed.
@nathanstander1493
Ай бұрын
@@Cloyes01 thanks for responding
@Thebombonlyone
10 ай бұрын
No torque spec on the chain tensioner....
@skygirl341
Жыл бұрын
So just to be 100% clear I don’t need a timing lockout tool to do my timing on the specific motor so I just wasted $89?
@Cloyes01
Жыл бұрын
The tool is not required, we did not use one in this video, but it can be helpful.
@HandyTim
3 жыл бұрын
Should the bolts be replaced with new torque to yield bolts?
@billanderson5774
Жыл бұрын
The cylinder head bolts are torque to yield, and should be replaced with new bolts, which must be purchased separately (unless a rebuild kit specifically includes those). The vvti camshaft phasers also are torque to yield bolts, but new bolts should be included with new gear(s). If you are replacing head gasket, I would also recommend replacing the vvti phaser gears.
@timocrosby
3 жыл бұрын
HELP! Why is it that my intake camshaft will not rest in the 11 o'clock position? It snaps forward to the 12 o'clock or back to the 10 o'clock position.
@Cloyes01
3 жыл бұрын
You are experiencing valve spring pressure as one of the valves are open. You can move the cam to either the 10 or 12 o'clock positions and time the engine. Just know that the other camshaft and the crank will also need to move slightly to get the marks aligned. As long as all three marked links are aligned to their respective sprocket marks then the engine is in time.
@timocrosby
2 жыл бұрын
Yep. fugured it out. Thanks!
@sonofsteve566
Жыл бұрын
Hi, during installation that slack between the phasers is normal? no matter how hard i try i cant element little play.
@Cloyes01
Жыл бұрын
Yes, some slack between the cams is normal. Both camshafts are dealing with valve spring pressures. Sometimes this will cause the cams to want to clock towards each other creating that slack. It really just depends where the engine stops as to what spring forces are against the cams. This can create slack between the cams, or between either camshaft and the crank, and it may shift the next time you turn off the engine.
@sonofsteve566
Жыл бұрын
@@Cloyes01 thank you for your response, that slack appears to create the chain to jump teeth, when the crank is turned. I'm guessing chain stretched ? or the tensioner is not doing its job.
@Cloyes01
Жыл бұрын
@@sonofsteve566 Both are possible if it is a used system. But turning the engine over by hand does greatly increase the chances of the chain jumping because of the violent movements of the camshafts due to the valves opening and closing and no oil pressure going to the tensioner. Even a healthy system can jump time when turning the engine by hand. Rotation with the starter is fast enough that the chain slack doesn't have time to shift back and forth which is what allows it to jump teeth.
@sonofsteve566
Жыл бұрын
@@Cloyes01 one more question please, original phasers, is there a concern of them locking when chain was removed did not hold cam when tensioner was removed. if cam phasers locked would this create a timing jump at crank?
@sonofsteve566
Жыл бұрын
@@Cloyes01 appreciate your effort in helping me out on these questions.
@tracypolockowbrooks
2 жыл бұрын
does the engine need to be removed to replace the timing chain?
@billanderson5774
Жыл бұрын
No
@jamesbonesteel2501
Жыл бұрын
@@billanderson5774 Seems like there is no way to get the timing cover out. I have loosened all motor mounts lifted motor and still can't get it out. How do you pull the timing cover out without without pulling whole motor? 2010 rav4
@jamesbonesteel2501
Жыл бұрын
Was not being creative enough and jump the gun on my question. Had to go through the bottom with engine as high as it goes.
@billanderson5774
Жыл бұрын
@@jamesbonesteel2501 Support the engine with a jack under the oil pan. Place a board on the jack to distribute the weight across the entire oil pan. Then remove the RH structural brace that extends from radiator support to (iirc) frame/sub-frame. Once that brace is out of the way, the timing cover can be removed by sliding it out thru the bottom of the car. You may have to also jack up passenger side of car to create extra space for timing cover removal. Make sure to support car with jackstands
@ابوحسينالهاشمي-ص3ص
3 жыл бұрын
👍
@dieselscience
2 жыл бұрын
My only complaint is that guitar riff is for Volkswagen, not Toyota.
@aminudinuntukdlmmuziksyaam5071
3 жыл бұрын
Toyota rav4 .2000 cc guna taimang cenge atau taimang balle
Пікірлер: 91