Probably got that noise figured already, but if the valve cover is tightened down to much the valves will tap on it. Mine did that after valve adjustment and just backed the nuts off a touch and she’s back to just healthy 22re ticking and not twacking 😆
@straightshooterz
2 жыл бұрын
85 4runner hasn’t been running in 10 years…brand new battery, ran 12 volts directly to the fuel pump and it runs/ turns on, cleaned throttle body. When I spray starter fluid into the manifold, vehicle bogs and hiccups to start up…that tells me it’s getting pressure. it actually ran for about 10-15 seconds til the starter fluid dissipated. No response when I throttle. Only when I used starter fluid I rev’d it pretty high.
@AutobahnDan
5 жыл бұрын
Just got that same Vessel ratcheting driver! I remember seeing a lot of those Philips screws with a dot on them when I had my runner!
@Toyotas_n__Tools
5 жыл бұрын
Nice what year runner? Did you know that you can buy the blades for like $7 and have a new clean shaft screwdriver? They also sell devices that slide onto the shaft nice n tighly like a magnet thing and also a way to have it hang from a cord. I really like jis they grab phillips better then phillips. I would like to pick-up this bit selection they have with different bits of girth and length. How about that comment ^^ LOL
@AutobahnDan
5 жыл бұрын
Yota Doug's Tool Collecting Channel it was an 87 Didn’t know that, but for $17 on Amazon, it’s not too bad to get a new one. Seen those magnetic jimmys, the Philips fit perfect though! I found a few photos where you see the Vessel stay into the screw on a wall without falling off!
@Toyotas_n__Tools
5 жыл бұрын
@@AutobahnDan Been thinking about this and some other ones of this style, look at the knurling! www.amazon.com/Vessel-900-Megadora-2x400-Screwdriver/dp/B001VB88F6/ref=sr_1_7?keywords=vessel+screwdriver+shaft&qid=1554880643&s=hi&sr=1-7
@ActiveAtom
5 жыл бұрын
We think we too have that vise lets see, is it an Scout we have the 31/2 version we refurbished it and are only a few details and a machined handle away from wrapping it up here. Yes make small adjustments try it out and adjust again and try it again, this applies to our machining world as well. Thank you for the sharing Lance & Patrick.
@Toyotas_n__Tools
5 жыл бұрын
Nope its actually a columbia, Its been around forever i need to ask my dad where it came from exactly.
@ifitsnotbrokenfixit1193
5 жыл бұрын
This has to be your longest video to date.
@Toyotas_n__Tools
5 жыл бұрын
I hope to do more of these type of help videos, appreciate you stopping by!
@viciousme90
2 жыл бұрын
yeah i bought a rebuilt one and had to adjust it in my mixture was off
@markmahecha8974
4 жыл бұрын
Can you make a video of where the O2 sensors are located? Please
@Toyotas_n__Tools
4 жыл бұрын
Mark Mahecha got Instagram or Facebook?
@markmahecha8974
4 жыл бұрын
@@Toyotas_n__Tools yes I do my Facebook is Mark. A Mahecha
@markmahecha8974
4 жыл бұрын
I accidentally dropped my MAF..
@dundeeecroc
2 жыл бұрын
get a new one.
@321CatboxWA
9 ай бұрын
Too loose and the fuel pump runs when it should not.
Пікірлер: 18