Great video. Thanks for sharing your knowledge with us.
@scottcannon2674
Жыл бұрын
Thanks. Looks really easy.
@silashobson-kl6qm
Жыл бұрын
I appreciate your video brother thank you 🙏
@PhilipHarrington
Жыл бұрын
Nice work thanks.
@kilanorman-bogana7099
8 ай бұрын
Use an old pad to retract the piston back so you don't damage it.
@joelw8912
4 ай бұрын
What did you do at 4:44 when vid stopped I’m stuck there, rotor is loose but won’t come off
@Alex-ip6nd
11 ай бұрын
Does anyone know where the cruise control fuse is located? Prado 150, year 2014, engine 2.7.
@joelw8912
4 ай бұрын
Wish I read comments first .. this video is a proper stitch up .. 🤦♂️
@kenlawton1531
Жыл бұрын
How's the brake dust with the DBA extreme pads?
@GrahamSmyth-um6uh
11 ай бұрын
Very little that's why they are the best
@andyflans9966
6 ай бұрын
Important: Detention of the handbrake will likely be necessary.
@UPP4BRI2LI0NS
Жыл бұрын
It appears your drums were fouling as the rotor didn’t come straight off. How did you free it up? It appears it had been edited out.
@jeremyb8493
Жыл бұрын
Seized handbrake cables?
@UPP4BRI2LI0NS
Жыл бұрын
@@jeremyb8493 they forgot to add in that the brake tension requires backing right off to be free of the drum. I learnt this the hard way. There is a slotted hole with that appears to be a cog looking wheel in the hole. This is the adjuster. Flick it which ever way loosens the shoe. This is also the adjustment to be made to tension the handbrake. I found all this out the hard way.
@jeremyb8493
Жыл бұрын
@@UPP4BRI2LI0NS thanks, yeah me too, just tore the whole lot out and will hand it to my mechanic for now… right pain in the behind!
@UPP4BRI2LI0NS
Жыл бұрын
@@jeremyb8493 haha. Yeah shot house hey. This video just annoyed me cause they have edited that part out.
@-boska
Жыл бұрын
@@UPP4BRI2LI0NSwish I saw these comments. Think I’ve just stuffed mine up now 🤬 what a shit video for missing that
@ariarfiandi
2 жыл бұрын
Do you have to bleed after the installation ?
@Bob_buoi
2 жыл бұрын
No bleeding needed as we pressed the brakes piston back with the brakes reservoir lid opened.
@adamconnolly7478
2 жыл бұрын
USE TECHSTREAM to bleed, its easy!@
@Mike-ry4ti
Жыл бұрын
Toytota wanted $1600 for new pads and rotors... bloody rip off, I can buy all the tools needed, after market parts and still save cash!
@josephiturra587
Жыл бұрын
Oh what a rip off …….
@callanmurphy9807
7 ай бұрын
A single rim from Toyota is $1650 too lol
@adamstrother4377
12 күн бұрын
Read the comments first. They cut out the most important part. Adjusting the handbrake adjuster. You can see when he can’t get it off. He obviously made the mistake, should have left it in to show people what happened. Dick move
@rodbender7946
10 ай бұрын
I followed this video and stuffed the shoe retainer clips. You don't know how to do this job properly and your misguided steps end in disaster. Take the video down. Learn from Forby diesel, not this guy
@mtmjoziadventure1409
8 ай бұрын
I second to this. He should mention that he needs to loosen the handbrake by adjusting through that small hole on the rotors before removing the rotors, otherwise you will stuffed up the clips. I recommend he needs to edit the video and add subtitles to remmind the viewers before they stuffed up their brake clips. Cheers kabayan.😊
@callanmurphy9807
7 ай бұрын
Have you boys got a link for it? I've got the same project on a kdj150
@damiensutton1057
2 ай бұрын
Hey hey you skipped a bit because I had trouble brake pads getting caught on rotor
Пікірлер: 36