🎵🎶🎵🎤 She's a maniac, maniac oh oh 🎶🎵🎶 Keep singing through this challenging week, Peter! ❤❤❤
@tyranakok
7 ай бұрын
Thank you, sir! My lights came on after a brake bleed on 2009 Lexus 460 LS. This worked to perfection!
@jimrossabrena7955
10 ай бұрын
This worked! I used a very similar autel scan tool. Chose linear offset in the drop tab and it passed the test!
@tanveerahsan2050
3 ай бұрын
Hi mate, could you share the Autel device model which you used?
@ParaBohn216
2 ай бұрын
I’d also like to know as well
@billsimpson604
2 жыл бұрын
Stuff breaks, especially on high mileage, older vehicles. On today's vehicles, sometimes even the dealers can't fix them. They change expensive parts until they find the problem, wasting hundreds, or even thousands of dollars. Be thankful they don't spread salt on the roads around there. Throw in some corroded wires, and you need a team of electrical engineers to determine what is wrong.
@ricardoandrade1313
Ай бұрын
ohh, nice!! great shot dude!
@DavidBeatypersonal
Ай бұрын
Followed this procedure but my lights remain on VSC ABS etc How do you clear them?
@zakdorgam
Жыл бұрын
Based on my experience, I have noticed that even if you delete the errors, the brake light and ABS warning lights can come back on again. To resolve this issue, I suggest putting the vehicle in service mode, changing the brake fluid, and bleeding it thoroughly. Additionally, using a paper clip on the OBD can help ensure that your car runs without any problems.
@Wicked_He_Bad
2 ай бұрын
What is the model of your autel????????????
@LAactor
2 жыл бұрын
I agree with Alan Eaten about the battery. I had an 08 Rav with dead alternator. Christmas tree lights and brake system weak. Electric power steering so that was crazy too for customer who needed to try to limp it to shop. They knew better than to risk a tow. That little trunk 12V batt is KAPUT.
@LAactor
2 жыл бұрын
New glasses! Hopefully your old ones didn't break? Are those Zenni optical? America's Best makes some with good deals too. The eyeglass manufacturers are making so many durable plastic hybrid lenses lately. Hope you like them!
@paulodisano502
2 жыл бұрын
Great video, Peter. Cheers my friend.🇨🇦🇺🇸
@Nissan300zxshowcar
Жыл бұрын
Great video! I have a gen 2 and 3, can you advise what scan tool you recommend for things like this?
@maloosecat123
Жыл бұрын
question about GEN2 Prius: watched your excellent video. Can weak Prius auxilary battery (say 11.5V) be put on a trickle charger connected to a power outlet to perform lenghty computer procedures/diagnistics? I need to know this for bleeding the brakes; my auxilary battery is weak. Thank you
@benzerah
2 жыл бұрын
Thanks a lot for the information...it was very helpful 👍
@roothegreatest5476
2 ай бұрын
Hi I have 2011 Auris with same problem but through the learning procedure the ABS light is not flashing to learn it. Any idea? Thanks
@alanwagen
2 жыл бұрын
I think it is the battery. Weak batteries freak the cars out.
@aliciacarrillo7427
Жыл бұрын
What kind of scanner do you use for Toyota’s ❤
@ELSHAD_MRZ
2 ай бұрын
Why does the VSC indicator not light up when the ignition is turned on?
@josegarcia-th3pj
3 ай бұрын
in my case blinking stop half the way and calibration is not done, do you think is hardware or air in the system
@aliameer786
2 жыл бұрын
Thanks man it really help
@nicholasg9804
Жыл бұрын
air conditioner has faults , its the sun sensor, dont worry about that if thats it...
@alondramenendez4274
2 жыл бұрын
witch Autel scanner model number ,are you using ?
@bwest-yq3uc
2 жыл бұрын
Try two fingers of bourbon and relax...works for many others mechanics.
@ReactbyWin
2 ай бұрын
Which test tool you used ?
@tyranakok
5 ай бұрын
Hi, can techstream tell me where my brake fluid leak is coming from? It seems to be coming from somewhere around the reservoir on my wife's Lexus 460LS.
@Zahidkhan-ym2cz
Жыл бұрын
Very helpful
@GreaseMonkChronicles
Жыл бұрын
Mines have the same code, I’m unable to learn the valve offset. It comes up failed learning offset
@GreaseMonkChronicles
Жыл бұрын
I’m using a AUTEL and tech stream. Any ideas
@Wizardry77
Жыл бұрын
Did you solve this issue?
@GreaseMonkChronicles
Жыл бұрын
@@Wizardry77 hey yes ended up replacing the abs module, and a job that was. After that did the calibration and worked. So in most cases the just by learning the linear valve would do it.
@Wizardry77
Жыл бұрын
@@GreaseMonkChronicles thanks appreciate the response
@tintim5011
Жыл бұрын
thank you so much 😊
@pfoxhound
Жыл бұрын
Thank you!
@mavilla2000
Жыл бұрын
Thank you for this great video. The scanner is an Autel Scanner MaxiSys MS906BT. Is it right?
@lyasselyassou3533
11 ай бұрын
Is there any way to do it with maxicom MK808 I tried but it doesn’t show me that option besides code reading and live data, do I need to update or what
@wpcote108
2 жыл бұрын
I changed an actuator and Brake pump in a 2013 Prius and I cannot eliminate the C1345 code... I tried several times using techstream.... any other suggestions? Thank YOU in Advance!
@alexnochvay2366
Жыл бұрын
Have the same issue
@alexnochvay2366
Жыл бұрын
How did you fix it ?
@geraldhk1
Жыл бұрын
Same
@geraldhk1
Жыл бұрын
May I know what is the solution? Is it related the battery?
@braschlosan
Жыл бұрын
Im having the same problem in a lexus hybrid
@mosal4759
2 ай бұрын
Thanks
@ashtarbeg6282
9 ай бұрын
Hi, could you please tell me which Autel scanner are you using, I have got an Autel scanner but it does not have that special function where I could do the job ( linear valve offset).
@thomasbenam-dv7vb
8 ай бұрын
Actually I had same issue but once I bought the update witch is 120$ year membership and end up updating all software and finally got special function
@richards3553
2 жыл бұрын
Hi. Which model of Autel tablet is that? Thanks.
@JoshHuntzy
Жыл бұрын
Should I take it to the Toyota dealer and have them do that?
@nas979
Жыл бұрын
I love your scan tool, what is the name of it
@robvlob
Жыл бұрын
What scanner are you using?
@markhogan1025
Жыл бұрын
Thank you for the video. What model of the Autel scanner do you have?
@angioman
Жыл бұрын
Dis u ever figure out what model autel to get? I need one for the same problems
@markhogan1025
Жыл бұрын
@angioman I never heard back from him on the model number, however I bought the PC plug to the car and found something online that worked for me. Much cheaper route
@danielwang7335
Жыл бұрын
Could you share what you used to fix that? I too have gone thru a few scanners. Thanks!
@bertstutzman3136
8 ай бұрын
What computer model do you have
@sonofliberty92
2 жыл бұрын
Them damn birds...
@user-nb7fs3me4h
6 ай бұрын
2013 Prius changed booster and pump with used unit. Bled using Topdon will not complete linear valve calibration. It will cycle and make noises, but Codes remain. Help!
@williamvaughn2938
5 ай бұрын
Any resolution?
@user-nb7fs3me4h
5 ай бұрын
@@williamvaughn2938 , yes. I ended up removing the unit and leaving the junkyard accumulator and reusing my original to the car brake booster assembly. It programmed immediately. All codes cleared and linear offset done. However, I still noticed that the accumulator is constantly running like before. This leads me to believe that the junkyard accumulator unit is either on its way out or the original to the car booster is damaged making the junkyard accumulator continuously run. I stumbled upon an internal Toyota publication stating that the accumulator loses pressure over time and that the booster cracks internally. Thus, any junkyard model not equipped with the new booster and accumulator assembly will essentially mean you are on borrowed time. Mine works currently but buzzes every 30 seconds. I’m again on borrowed time. Thus, I’ve ordered the accumulator and booster from Toyota and will install it sometime soon. It’s the only way to permanently fix the issue. The part numbers have changed from Toyota. This typically means the parts have been updated. I paid $1300 for the new parts. Also, the new accumulator is no longer two black cylinders. The updated for the regular Prius (not C ) is now two silver cylinders. That may help if looking for updated used junkyard units. Good luck!
@boyhanep4428
2 жыл бұрын
What scanner do you use, please?
@eagle1148
9 ай бұрын
What software can I use for this?
@taddickenson5577
Жыл бұрын
Which model Autel Scanner?
@flashsushi1843
2 жыл бұрын
Autel is not Techstream is it? That $500 device sure looks handy if it can cure a lot of these electronic problems.
@LAactor
2 жыл бұрын
Autel is Autel and Techstream is Toyota and solely Techstream only. Any non subscription that calls itself Techstream is a hack and is not legal to be commercially sold. Autel makes software and includes the tablet or handheld interface. That being said, many devices exist in the market that does everything you need. Even keys. You just pay more for what you need to do. Still less than Techstream and no annual subscription.
@Nissan300zxshowcar
Жыл бұрын
@@LAactor Can you advise which Autel unit you are using?
@ferencs.harmat7049
Ай бұрын
Camera was blurry the whole time
@johnstefanick5216
2 жыл бұрын
Hello, I really like your thorough Prius videos. Thank You! Could you advise an issue with braking? It is what I am calling delayed brake release. After you take your foot off the brake they do not release, there is a two second delay before the wheel is freely rolling. 2007 Prius, 240k, already replaced the brake booster, no significant improvement and it is the front brakes.
@jeremywarner9737
Жыл бұрын
what ended up fixing this for you? i have this happening but especially with the driver rear wheel
@julioanthony1951
Жыл бұрын
@@jeremywarner9737 hey bro how did you fix yours I have exactly the same problem
@jeremywarner9737
Жыл бұрын
@@julioanthony1951 I put a new ABS pump in mind from a junkyard it took like 3 hours to follow the bleeding procedure that took a fancy computer to do the bleeding but I knew that a dealership wouldn't touch junkyard parts. But since I fixed that this car has been amazing I'm getting astounding gas mileage and I put over 7,000 mi on it in two months
@julioanthony1951
Жыл бұрын
@@jeremywarner9737 thanks for the swift response. I should but buying a new abs in mind. Though the brake is still working till now
@KingCobbones
23 күн бұрын
I had the same problem in my 2006 Prius (331,000 miles), but the brakes would drag for about four seconds, rather than two. No codes came up on BlueDriver or my cheap OBDII readers, but Techstream showed C1247 and C1345 codes (for.brake pedal position sensor). After replacing the sensor and using the Techstream utility for calibrating linear valve offset, everything is back to normal.
@v2fe
2 жыл бұрын
I love your videos, but the camera focus has been terrible lately! Damn birds!
@davidnull5590
2 жыл бұрын
Thanks, I though I was the only one.
@LAactor
2 жыл бұрын
It's been a bad week. Pete, I know you have more on your mind this week, but to avoid focus problems, try to check the camera monitor if you can. But I understand when you are actively trying to diagnose a problem, fixing the problem is more important than camera focus. We are here with you for the ride regardless. Would be nice to see but to hear the walkthrough is better than nothing.
@braschlosan
Жыл бұрын
Please lock the focus on your camera. Much of the video wasn't viewable
@ramdanelimam7620
2 жыл бұрын
tanks you are the best
@mohamedmohamed-lk8um
2 жыл бұрын
I need test and light dash
@LAactor
2 жыл бұрын
It is because of the moon cycles. The new moon period just ended. And the full moon is starting to show and we all know the full moon brings out the lunatics. I had one today. The public is awful now.
@nicholasg9804
Жыл бұрын
i have same code
@johnlacroix1639
2 жыл бұрын
This video I liked it a lot ,keep up the great work. WOW very interesting 1st class very kool great info.,, AAAAAAAAAAA++++++++++++ again great
@robvlob
Жыл бұрын
I recently had new tires and an alignment check. After which the (!) l, ABS, VCS, and BRAKE lights came on and won’t clear. The tire shop’s scan tool can’t calibrate, and the dealership wants $192 to be calibrated if it can’t it’s still $192. I’d rather put that money toward a scan tool that can calibrate. What is the tool you used, or do you have any other suggestions, and maybe an appropriate cost for the tool.
@KingCobbones
23 күн бұрын
I had the same problem in my 2006 Prius (331,000 miles) No codes came up on BlueDriver or my cheap OBDII readers, but Techstream showed C1247 and C1345 codes (for.brake pedal position sensor). After replacing the sensor and using the Techstream utility for calibrating linear valve offset, everything is back to normal.
@ilyaspatel5528
Жыл бұрын
Hi ur video qulaty very poor when u make it video make sure its not blaree! I dont think so ppl see ur video clearly sorry to say no good only mechanich knows coz they all ready knows 😂
@StarFlyer-th8so
14 күн бұрын
Dear Sir... my 2007 prius suddenly shut off power and all dash light come on like death triangle. after that i can resart again , what may be the reason ? i can not go out with this car , bec i am afraid like- any time engine can shut and any car from behind can hit me . pls sir help me with a suggestion
Пікірлер: 87