Does it require a longer supercharger belt? My stock belt doesnt fit after this spacer
@sugaris
5 жыл бұрын
That's a tidy HP gain for a bolt on option.
@ILovJeep
5 жыл бұрын
Question of the day: interchiller or spacer - do any of those void the entire Trackhawk warranty or just the modified parts ?
@ForcedInductionInterchillers
5 жыл бұрын
We can't make a direct statement of "yes you will not void your warranty". However what we can tell you is, some OEM's have recognised our parts do not and cannot hurt your engine, in such they have in the past fitted parts pre delivery and given customers in writing that it will not void new car warranty other than to the AC system with the chiller. In regards to the spacer plates, in very simple terms we are replacing some poorly designed gaskets with thicker better gaskets that also reject heat. Both modifications can be removed very easily, the chiller is not making the car do anything it cannot already do you simply need to be in the colder conditions to achieve the same result.
@ILovJeep
5 жыл бұрын
Forced Induction Interchillers Thanks for being honest . Who is your preferred installer in Melbourne ?
@ForcedInductionInterchillers
5 жыл бұрын
There are many installers in VIC that can handle the install for you.
@BOOSTEDLUCKEY
3 жыл бұрын
so that was just a back to back pull the spacers and it gained that much?
@ForcedInductionInterchillers
3 жыл бұрын
Yes you can also find loads of independent reviews, dyno results, track results, thermal imaging and data logs here: fiinterchillers.com/hellcat-spacer-plates-reviews-and-results/
@BOOSTEDLUCKEY
3 жыл бұрын
@@ForcedInductionInterchillers i’ve been doing a lot of research and i’m aware of the thermal capabilities with separation of the blower and your thermal blanket stuff just surprised that with that small of a runner length increase they pick up that much, hats off to you guys
@ForcedInductionInterchillers
3 жыл бұрын
@@BOOSTEDLUCKEY whilst the runner will have an effect that it not what the plates are fixing. The factory intake gaskets leak boost into your crank case, this causes several issues. 1 that air should be going into combustion. 2 that pressure in the crank case will make it harder for the pistons to drive down the bore 3. it causes increased oil blow by 4 the plates allow the blower to run colder. 5 the intercoolers run colder 6. the intake air temps are colder 7 the IAT sensor resolution is more accurate. So there is quite a few issues being resolved and we are sure you would rather your boosted air going into combustion and not your crankcase!
@BOOSTEDLUCKEY
3 жыл бұрын
@@ForcedInductionInterchillers ahhh okay makes sense i completely forgot about the flimsy gasket it replaced!
@BOOSTEDLUCKEY
3 жыл бұрын
@@ForcedInductionInterchillers where can i purchase the kit, and will this require me to use a different belt, i have a ripa incognito pulley with the gates green belt with no additional tensioner pulleys and a stock upper pulley
@William-_-Cook
4 жыл бұрын
Do you need to lower the engine or anything for fitment?
@ForcedInductionInterchillers
4 жыл бұрын
no you just need to remove the blower
@jesseclifford4970
3 жыл бұрын
Would I need to Retune my Hellcat after adding this part.
@ForcedInductionInterchillers
3 жыл бұрын
If you are leaking significant boost from the leaking factory intake gasket then yes you will. Obviously you want to fix that issue so even if a tune is needed it's still a good thing and will only be a minor adjustment in your tune. If it is on the stock tune then it will be fine the OEM calibration will not be leaking boost from when it was first made, but after a few miles it will be leaking boost, so you are essentially taking it back to the original boost level before the stock gaskets breached and leaked your boost out.
@likeachamp91
3 жыл бұрын
With the spacers do you need a new belt? Thanks
@ForcedInductionInterchillers
3 жыл бұрын
most people do not need a new belt if you do it will only be a half size increase
@likeachamp91
3 жыл бұрын
Forced Induction Interchillers oh ok cool thanks
@captain052A
Ай бұрын
@@ForcedInductionInterchillerswhere can we find this belt? I cant find a longer belt anywhere! Help
@ForcedInductionInterchillers
Ай бұрын
@@captain052A 10mm plates 5.6mm longer belt, 1" 14mm longer belt longer belts can easily be looked up on Summit Racing or Gates Belts websites. If you are struggling please email the office with your current belt part number and also advise what thickness spacers you are using.
@jameslawhorn146
4 жыл бұрын
With mods to the tune or no??
@ForcedInductionInterchillers
4 жыл бұрын
no modifications made to the tune, OST had already tuned the car we bolted the plates on and did a back to back run on the same day within a couple of hours of both runs
Пікірлер: 25