Hey Man, that looks good. Nice and simple. Easy to work on.
@allproexteriorservicesllc5338
Жыл бұрын
Thanks! It has been a productive trailer.
@ga-prowashllc12.5
3 жыл бұрын
My brother great job on building new system I use a vent cap for Bathroom under a the sink it's has a Built-in check valve no trash can get into your tank I put one on my 330 tote it works great good job on buliding your trailer Road dog dirt relief
@allproexteriorservicesllc5338
3 жыл бұрын
Thanks. I never thought about vent cap from the bathroom. That is a great idea and may have to use it!! Thanks again
@scottwillis4328
3 жыл бұрын
Hey brother. Great videos. I have a small lawn care business solo operation. Adding housecwashing next year. Having to devide my trailer basically in half. Half lawn side half downstreaming side. 6x12 trailer so will be tight. What did you end up doing with the spare tire? I'm having that same issue with it having to be taken off the side to accommodate the reels.
@allproexteriorservicesllc5338
3 жыл бұрын
I was debating on cutting the off the channel in front of the trailer, but decided against that. I also thought about just keeping in back of the truck. But after working the trailer, I think I will move the mount to the other side. I would also recommend that you make the reel rack off the trailer as far as you can to maximize your space. Thanks for watching and let me know if I can help with anything else!
@mauropasillas2054
9 ай бұрын
Nice set up ty👍
@properpreparation3213
3 жыл бұрын
Nice build! Question... what is the bypass hose (valve) for that your run from your pressure washer to your tote? What's it's function?
@allproexteriorservicesllc5338
3 жыл бұрын
The original bypass hose was connected to unloader & then went to the hoe inlet on the pump. So went you left off the wand, the water recirculates but will eventually heat up. So I disconnected the connection on the inlet and plugged it then ran the bypass hose to the buffer tank. With this set up, it doesn't matter how long I stay off the wand and the water will never get hot in the pump.
@thomasatkins1675
Жыл бұрын
I have a question, will the pressure washer still be able to feed from the tote when the water is below the pressure washer line?
@allproexteriorservicesllc5338
Жыл бұрын
The water must be above the bulkhead fitting that feeds the pressure washer. Thanks
@GoldenState408
2 жыл бұрын
Awesome clean build. Can i ask what size is line is feeding your pressure washer?
@allproexteriorservicesllc5338
2 жыл бұрын
Thanks!! I used a 1" line to feed the 4 GPM unit & 1 1/2" line for my 9 GPM unit.
@GoldenState408
2 жыл бұрын
@@allproexteriorservicesllc5338 i like your setup and imma try to replicate that. For a 5.5 gpm do you think i should use 1” or 1-1/2”?
@allproexteriorservicesllc5338
2 жыл бұрын
@@GoldenState408 1 1" should work perfectly.
@GoldenState408
2 жыл бұрын
@@allproexteriorservicesllc5338 thank you Sir! hope you killin it right now
@h2owashpros154
3 жыл бұрын
Did you buid those supports for the pressure washer and hose reels yourself? I need to do that for my trailer
@allproexteriorservicesllc5338
3 жыл бұрын
Yes, I did all the fabrication work. I am in the process of adding another stand for my 8 GPM unit. BTW, I love them being mounted on the back of the trailer for access.
@braddgullickson9926
3 жыл бұрын
Very informative videos. I'm thinking about offering pressure/soft washing. This will be my second year mowing lawns and I was just wondering if you're still gonna mow? It sounds like there's more money in washing. I just do this as a side hustle, I work full-time elsewhere. Keep the videos coming. 👍
@allproexteriorservicesllc5338
3 жыл бұрын
Bradd, I do not plan to mow next season. The pressure washing has a better margin when done right. Make the move and you will not regret it! Thanks for watching
@dantec8854
10 ай бұрын
What size of filter and clear hose from tank to pump did you use sir?
@allproexteriorservicesllc5338
9 ай бұрын
1 1/2" for the pressure washer. You could use 1" & that should work. Thanks
@zadok22
2 жыл бұрын
Hey, where did you get the IBC tote clamps to hold down the tank? I have never seen that before. Doing a build right now.
@allproexteriorservicesllc5338
2 жыл бұрын
I made the hold down clamps out of 2" angle iron. Thanks
@DIVEBABY64
3 жыл бұрын
How long is your bypass hose? I have seen some say it needs to 15’ -25’. Also do you run that drop stick almost to the bottom of the tank?
@allproexteriorservicesllc5338
3 жыл бұрын
My bypass hose is around 3 or 4’. The only time you need a long bypass hose is on a roof pump to cool the water. I have a drop stick in the bulkhead fitting towards to bottom of the tank. Thanks
@brandonh.4781
3 жыл бұрын
Where did you get the tie downs for the inch tank? The way you bolted it to the trailer?
@allproexteriorservicesllc5338
3 жыл бұрын
I made them out of angle iron. I didn't like the look of straps. Thanksn
@ohmimprovement5767
3 жыл бұрын
Its not a street t, it's more like a sanitary t if anything. I've actually never seen one of them in the Chicago area and that's what I've done my whole life lol. Also, if it was me I would remove that 90 you have leading to the pump and use a street 45 into a regular 45 to make it a long sweep for better flow to that pump. A street fitting has one hub and one male end. 2 45's make a 90
@allproexteriorservicesllc5338
3 жыл бұрын
Sweeping tee vs. a regular tee. It has great flow, but i do need to add a ball valve. Thanks
@NutcrewGaming
3 жыл бұрын
Hey buddy quick question i notice you pressure washer will suck the water up from the tank when you started it. you can see the water flowing from the tube to the tank. But my pressure washer wont do that. i bought the simpson 4400 4 gpm pressure washer and no luck. Can you shed some light?
@allproexteriorservicesllc5338
3 жыл бұрын
You probably have a direct drive pressure washer. A direct drive pressure washer will not suck water from a tank. You need to raise the tank above the pressure washer to gravity feed. If you get a bely drive or gear drive pressure washer, then they will suck from a tank.
@NutcrewGaming
3 жыл бұрын
@@allproexteriorservicesllc5338 yes sir, i do indeed have a direct drive pressure washer. what kind of pressure wash is the honda? is that bely drive or gear drive?
@allproexteriorservicesllc5338
3 жыл бұрын
@@NutcrewGaming I have a belt & gear drive. I like them both, but the gear drive is growing on me. Thanks
@NutcrewGaming
3 жыл бұрын
@@allproexteriorservicesllc5338 awesome, thank you sir
@dcsc4895
2 жыл бұрын
What size of line are you feeding the pressure washer with ? looks bigger than 5/8" ?
@allproexteriorservicesllc5338
2 жыл бұрын
That is 1" feed line. Thanks
@maxsherro8729
3 жыл бұрын
Hey brother, great video. I have the same washer how are you getting by without using a pump to push wasted to your washer?
@allproexteriorservicesllc5338
3 жыл бұрын
The belt drive machines suck water with no problem. Thanks!!
@maxsherro8729
3 жыл бұрын
No way that’s awesome I did not know that!
@maxsherro8729
3 жыл бұрын
Anyway you could post a list on some of these items?
@allproexteriorservicesllc5338
3 жыл бұрын
@@maxsherro8729 It would be tough. Feel free to reach out to me for assistance.
@maxsherro8729
3 жыл бұрын
Ok thanks!
@outdoordeerdogs9204
3 жыл бұрын
What size filters are them that your using
@FamiliaGuevara
2 ай бұрын
Can you share a shopping list?
@allproexteriorservicesllc5338
Ай бұрын
I do not have a part list unfortunately. Thanks
@nategarrison99
2 жыл бұрын
what size is the ball valve going to your pressure washer? looks like 1 inch?
@allproexteriorservicesllc5338
2 жыл бұрын
Yes it is 1". Thanks
@michaelc7283
3 жыл бұрын
Had a question on your SH tank. Do you manual fill it up? I heard that some SH suppliers won't fill up a tank if you have a drain spicket on the bottom of a tank. It has to be all solid. Just curious. Thanks
@allproexteriorservicesllc5338
3 жыл бұрын
I fill it myself at the local pool company.
@shawnjacks2072
Жыл бұрын
How did you secure that water tank down
@allproexteriorservicesllc5338
Жыл бұрын
I made some brackets that are bolted to the deck of the trailer. Thanks
@shawnjacks2072
Жыл бұрын
@@allproexteriorservicesllc5338 thanks for the reply I ended up doing 2x4 on all sides two rachet straps over top my welder was willing to make the brackets but the way I did it was much more stout imo I'm now working the plumbing and it's been a real learning lesson haha.
@zadok22
2 жыл бұрын
Just saw the first video. What will your fab guy charge to send me 4 of those IBC tote hold down clamps?
@allproexteriorservicesllc5338
2 жыл бұрын
Not sure. I can ask him when I see him again. you may want to look for a local fabricator. Thanks
@zadok22
2 жыл бұрын
@@allproexteriorservicesllc5338 true thx
@xtremepowerwashing1815
3 жыл бұрын
Love the build so far. A few tips I can give u is to definitely get yourself a sh tank with out any bulk head fitting at the bottom, the sh will eat those seals in no time and destroy your trailer..been there already..use that tank for your soap tank..def put a bigger beather hole in that tsnk... when I had a IBC tank I had about a 1/2 inch hole at the top and never had a problem with the debris getting in. Looking good. 👍🏻
@allproexteriorservicesllc5338
3 жыл бұрын
Thanks for the tips! Much appreciated. I will replace the SH tank hopefully soon. I did some more work today to bring it all together.
@xtremepowerwashing1815
3 жыл бұрын
@@allproexteriorservicesllc5338 Awesome.. and your welcome..
@rayrussell5903
Жыл бұрын
Can i get a list for the plumbing
@allproexteriorservicesllc5338
Жыл бұрын
I don't have a list. I purchased all my plumbing from Home Depot. 2" from the tank and reduced when connected to the machines. Thanks
Пікірлер: 64