Thanks. Very helpful to implement multi read or write blocks. 👏👏👏
@LeTomasAHUMADA
2 жыл бұрын
You are welcome Jianping Li 😊
@zivkospirovski2700
Жыл бұрын
very very good videos, with very low volume and also some scratches ....
@LeTomasAHUMADA
Жыл бұрын
Hi Zivko Spirovski! That can be possible 😅 most of the new videos created from this year have the new mic to sort that horrible problem 😊 hopefully the info on the video was useful for you
@hichemam2733
2 жыл бұрын
Thank you so much
@samanabdullah8408
24 күн бұрын
Thanks, why you write %mw62 instead of %m62 for back light , is not digital out put ?
@LeTomasAHUMADA
14 күн бұрын
Hi there! The backlight in the m172 requires a word variable that is why.
@fujiwara_kitonabas
4 ай бұрын
Can we use the RTU Modbus and TCP modbus simultaneously?
@LeTomasAHUMADA
4 ай бұрын
Hi there! If i am not wrong you can do that but if you want you can check it using code just to be sure 😊. What i am 100% sure is that you can only use ioscanner in one of them only but not in both
@husammohammed3947
2 ай бұрын
Hi dear, I have a serial devices connected to an ethernet gateway and then connected to M221 PLC I am using Modbus TCP IO scanner to read the data, but I have problem where I cannot change the slaves devices unit ID I appreciate if you can support me how to use the M221 as Modbus rtu over tcp ?
@LeTomasAHUMADA
Ай бұрын
Hi there! Not problem then the unit id in the ioscanner must match the slave id if you are using a gateway.
@bambel1867
7 ай бұрын
Hello tomas could you do an explanation on how to program a slave instead of master, please?
@LeTomasAHUMADA
7 ай бұрын
Hi there! I will try to do something in video soon. Basically, in the modbus serial port you will need to select slave instead of master and assign an address. Finally the master needs to read/write the %M and %MW of the M221.
@bambel1867
7 ай бұрын
@@LeTomasAHUMADA thank you! Your videos have helped me a lot, I start programing with ecostruxure one week a go
@erickruizabanto6976
Ай бұрын
Very good videos my friend, you make a comunication with vdf ACS580 ABB?
@LeTomasAHUMADA
Ай бұрын
Hi there! Thank you 😊. Unfortunately i only use Schneider products because is the only thing i have access to 😁 but i get one of those drives i will make a video.
@erickruizabanto6976
Ай бұрын
@@LeTomasAHUMADA I have another question, well at the moment I do not have access to the VDF that I am going to link, but I am already advancing the programming, when I simulate the m221 plc, the RTU communication blocks are at error 6, this indicates that the parameters are not the correct ones, is this error because I am simulating?
@LeTomasAHUMADA
Ай бұрын
@@erickruizabanto6976 in simulation the communication does not work so i advice you to get the real Plc to test it
@hicham5076
2 жыл бұрын
hi dear thank you very much for your help,in my case i have 8 blocks what i must do
@LeTomasAHUMADA
2 жыл бұрын
Hi Hichan, the best will be the ioscanner: kzitem.info/news/bejne/mGZjnqZtqmKJmY4 If you are using the blocks then my recommendation is to create an additional logic based on state that allows you execute the next block as soon as the previous one has finish ok or error.
@adi1257
Жыл бұрын
hai thomas, i have question....could you give me video how to force output plc 1 from plc 2.... for example i want to turn on %M1 in plc 1 with %M3 from plc 2.... tks regards
@LeTomasAHUMADA
Жыл бұрын
Hi adi1257! I have done this video a few months ago, i hope it helps you: kzitem.info/news/bejne/zJCr0mebb4OQhZw
@FlexpowerAutomation
11 ай бұрын
i dont know if it is just me but the link is saying "this shared file or folder link has been removed or is unavailable to you."
@LeTomasAHUMADA
11 ай бұрын
Hi there! It is totally problem of the link. I will update it during the week.
@LeTomasAHUMADA
11 ай бұрын
Hi there! It is totally problem of the link. I will update it during the week. Thanks! 💪🏻
@ademarlima105
2 жыл бұрын
consulta . para comunicarme con un hmi por modbus 485 tengo que hacer los bloques que indicas en este capitulo.
@LeTomasAHUMADA
2 жыл бұрын
Hola Ademar! Solo si usas el PLC como master en la comunicación. Pero es mas sencillo poner al HMI como master e indicar las posiciones de memoria a leer del PLC. Si usas una HMI de Schneider vas a ver que es sencillo de esta forma: kzitem.info/news/bejne/04OdyndvcKGLlYY kzitem.info/news/bejne/pYWfx3iNr5d4po4
@abdulkhalekkhaled5669
8 ай бұрын
Thank u 🧡🧡
@LeTomasAHUMADA
8 ай бұрын
You’re welcome 😊
@AhmedMohammed-rm3yy
2 жыл бұрын
thank you for your efforts, how can you get the address for inputs such 8640 and 8336 if i used M221 as a slave ,too? when I opened the analog input from configurations ,it doesn't appear
@LeTomasAHUMADA
2 жыл бұрын
Hi Ahmed, i recommend you to move the %I variables to a %MW variables.
@AhmedMohammed-rm3yy
2 жыл бұрын
@@LeTomasAHUMADA thank you for kindly reply , what do you mean by %I?
@LeTomasAHUMADA
2 жыл бұрын
@@AhmedMohammed-rm3yy i meant the physical input %I0.1 or %IW0.1 of the M221
@AhmedMohammed-rm3yy
2 жыл бұрын
@@LeTomasAHUMADA thank you for kindly reply
@jonathanchris697
2 жыл бұрын
Sir, can i use that function block too when i use io scanner?
@LeTomasAHUMADA
2 жыл бұрын
Hi Jonathan, i have not tried that to be honest. If you are using the ioscanner you can see that is much better than using the blocks… i do not use in my program the blocks. What you can not do is to enable the ioscanner for serial and ethernet at the same time.
@jonathanchris697
2 жыл бұрын
@@LeTomasAHUMADA okay thank you so much sir
@bechir.jaballah
2 жыл бұрын
Hello i am using the TM221CE16R it doesn't support PTO functions , can i use the RS485 serial port to send instruction to a servo drive that has also serial port , if yes can you give me a quick brief or a guide please .
@LeTomasAHUMADA
2 жыл бұрын
Hi bechir! as the M221 that you have does not have transistor output the use of the PTO functionality is not possible. As an alternative you could use the Modbus to control an LXM28 or LXM32 but i believe is not straight forward as using PTO or CanOpen (not for M221). I do not have a real experience using a MbSerial to control a servo so i recommend you to contact the technical support team in your country for some example (if there is something): www.se.com/ww/en/work/support/country-selector/contact-us.jsp
@bechir.jaballah
2 жыл бұрын
@@LeTomasAHUMADA yes after looking at the documentation i managed to stumble on the write_var block that is used to send word throw serial port and i think after knowing on which adress to send command for the drive i can instruct the servo from the plc as the rtu master, ps: i am using the Delta ASD-B3-0421-L servo drive
@LeTomasAHUMADA
2 жыл бұрын
@@bechir.jaballah i thought you were using schneider servo 😅. I believe it is going to be easy if you defined the ioscanner on the plc to communicate with the slave the problem is to check the address and the behaviour of the servo
@bechir.jaballah
2 жыл бұрын
@@LeTomasAHUMADA yes indeed that what i have done but just to make sure i am doing everything right , in order to send command from the plc to the servo we use the Write_Var and Read_Var functions after defining the adresses and the word , right ?
@LeTomasAHUMADA
2 жыл бұрын
@@bechir.jaballah the easiest way to communicate with a device is using a Ioscanner, take a look in the next video: kzitem.info/news/bejne/mGZjnqZtqmKJmY4
@sheikshiraznilam8749
Жыл бұрын
How to find out index Data 62 and index Data in 60 Please let me Know
@LeTomasAHUMADA
4 ай бұрын
Hi there! Those numbers are related to the %MW in the M221, is the buffer. For example You can use the %MW60 in your code directly. You can select the number that you want
Пікірлер: 47