Dude you are an amazing and intelligent person. I can only imagine what you would come up with if you had a fully loaded laboratory and engineering shop behind you. Someone either in the corporate world or the government needs to fully fund your ideas and inventions. I believe if that was to happen our world would advance 200 year's in a matter of months. Thank you for doing these video's I appreciate all your time and insight so please keep up the AWESOME work and I'll keep coming back for more and sharing your video's with as many people as I possibly can. 👊😯👍
@pakxnayvy128
4 жыл бұрын
These are complete videos about transformer which you make expert on transformer Bobbin size kzitem.info/news/bejne/0IGQuoKkbH94nYY Swg wire weight kzitem.info/news/bejne/r3h-4INjkaiirGk Transformer wire primary and secondary kzitem.info/news/bejne/s3ts22uojYRol3o Transformer core weight kzitem.info/news/bejne/rml-tpinnWNhZJw Transformer winding kzitem.info/news/bejne/w6uI3qWqoZV3p3o
@freeenergytransformer5842
2 жыл бұрын
Engineers design transformers to be as small and light as possible to save on materials and shipping costs, yet still meet the electrical requirements. Transformers have been around for over a hundred years, and the basic design has not changed much. The government does not understand how they work, but THEY do. Transformers are wound with a specific number of turns of wire around a core. The turns are evenly spaced and there is a specific amount of insulation between each turn. The insulation is necessary to prevent short circuits and keep the voltage from one winding to another winding from becoming too high. The windings are connected in series or parallel to create the desired voltage or current. The cores may be made of air, iron, or other materials, depending on the type of transformer. Transformers are used in power plants to convert high voltage AC to low voltage DC so that it can be used by consumers. Transformers are a necessary part of our electrical grid, and are used to step up or step down voltage levels. In fact, they are so important that most technical books include a section on transformer winding and calculation. However, free power transformers are not in mainstream technical books. We will share with you how to generate free electricity with transformers.
@joshr.4398
Жыл бұрын
Transformers only change the voltage and amperage they don't turn ac into dc they actually are used to block DC in push-pull amplifiers, a full bridge rectifier changes ac to dc
@L30x
Ай бұрын
Best channel no scam so far
@narenderverma4203
Жыл бұрын
Thanks a lot for nice information about Transformer rewinding
@MESEM1994
2 жыл бұрын
Hesaplamanın başındaki( turn per V hesabı) 'ında kullandığınız 7.5 degeri nereden geliyor? Anlayamadım.
@akdenyer
3 жыл бұрын
Where do you get your laminations and bobbins from? I find the winding constant is more like 6.2 for a 60Hz TX with a primary of about 120V however a little playing is often necessary.
@tommybrown3095
2 ай бұрын
This is really great, where did you get the 7.5 for computing the TPV=7.5/CA(inches)
@johnwaltersalas8601
9 ай бұрын
so its primary over the secondary winding. is it strictly this way or its reversible?
@victorcharles8194
Ай бұрын
Nice explanation also Please teach us complete design a generator with winding calculation and formula....
@csandoval82
2 жыл бұрын
Hi guys. Where do you get all your components for building transformers? I’m very interested in winding some up. Keep up the good work. 👍
@FIXDIY
4 жыл бұрын
Excellent You are the teacher
@TechTins_Projects
3 жыл бұрын
where did the number 7.5 come from in your initial turns calculation?
@MaheshBaburajapalayam
2 жыл бұрын
Yes same question
@physicsisawesome696
4 жыл бұрын
I like to learn electronics. So it is very useful video to me. Thank you
@dannydanilopunzal25
3 жыл бұрын
How do you calculate, the size of conductor for primary. And seconadry?
@AstralToneworx
2 жыл бұрын
What was 7.5 in the TPV calculation?
@noelsojr
11 ай бұрын
up
@jimmatrix7244
Ай бұрын
@@noelsojr ??? What is up?
@Abhinavsarvesh1111
Ай бұрын
Brother, which part is CA in a Transformer core. Please reply.
@CalemCems
4 жыл бұрын
yes!! the formula for the windings, thanks man.
@somethingnew5496
4 жыл бұрын
nice video...
@josephduazo5421
4 жыл бұрын
How did you get the exact no. of awg?
@CalemCems
4 жыл бұрын
the how thin... or how thick the wire..... yeah thats a diferent matter....dang it.
@georgeompad1540
4 жыл бұрын
good day to you sir! where did you get the 7.5?
@hansemanuelvinzon1985
Жыл бұрын
Is this formulas are constant?
@neomarc9946
2 жыл бұрын
Very clean winding technique.
@bambarhan
4 жыл бұрын
Thank you for sharing and teaching others. You’re genuine creative.
@pakxnayvy128
4 жыл бұрын
These are complete videos about transformer which you make expert on transformer Bobbin size kzitem.info/news/bejne/0IGQuoKkbH94nYY Swg wire weight kzitem.info/news/bejne/r3h-4INjkaiirGk Transformer wire primary and secondary kzitem.info/news/bejne/s3ts22uojYRol3o Transformer core weight kzitem.info/news/bejne/rml-tpinnWNhZJw Transformer winding kzitem.info/news/bejne/w6uI3qWqoZV3p3o
@somethingnew5496
4 жыл бұрын
off course great video
@jeffurbano1355
3 жыл бұрын
What is the formula for the number of wire gauge needed for the primary and secondary?
@franukito
Жыл бұрын
two plus two is four, minus one thats three Quick Maths
@gilebea
4 жыл бұрын
Good evening. Congratulations on the class. You used 1.2mm wire for the secondary and 0.3mm for the primary. How many amperes does this transformer support for these measurements? Thankful.
@ilovethatkatielovesclassic8771
4 жыл бұрын
look it up those charts are everywhere...
@gilebea
4 жыл бұрын
Excuse me. I thought you knew what you were teaching. Thank you.
@alfredterprey6677
Жыл бұрын
@I Love That Katie Loves Classic Books well it's difficult to find and understand
@ابتكاراتوتحديثاتفنيه
4 жыл бұрын
جميل عملك لكن في شغله انت هامله ربط اسلاك الكهرباء بالمحول ضعيف وقد ينفصل يفترض تربط سلكين في المحوله حتى لابنقطع واير التجهيز تحياتي وانا اتابع كل ماهو جديد لك
@ubtech2938
4 жыл бұрын
يا احمق هذا الشاب اجنبي و لا يفهمك
@Prem-do3ud
4 жыл бұрын
Bro Ampere kaise nikalenge.. ki ye kitne Ampere ka h ya phir Hume agar 2 amp 5amp ki banani ho to kaise calculate karenge
@electronic7979
4 жыл бұрын
Very good 👍
@HOLLYWOODlosANGELES
4 жыл бұрын
*J'aime beaucoup le côté pratique de votre chaîne ! À cela, vous mettez de la théorie, c'est encore mieux !! Merci.*
@dazzlenconfused
4 жыл бұрын
Could you share or have any info on how to choose the right bobbin ?
@rajannarayanan2759
2 жыл бұрын
Very good explain thanku
@xverteX1
4 жыл бұрын
Good video very useful but use 7.5 only if the frequency is 50hz
@carl3836
4 жыл бұрын
How the 7.5 is being calculated ?
@xverteX1
4 жыл бұрын
It have a bigger formula
@tommybrown3095
2 ай бұрын
What if the frequency is more than 50Hz
@isbushandpen
3 жыл бұрын
Hello! I am always curious on how did you get the 7.5 in solving the turn/volt. is it a constant??? thank you guys
@owaisahmed3838
3 жыл бұрын
constant for only 50 hz frequency.
@freeenergytransformer5842
2 жыл бұрын
In order to generate free electricity with transformers, you will need to wind the transformer yourself. This is a process that is not typically found in mainstream technical books, but we will share with you how to do it step by step. The first step is to calculate the number of turns you will need for your transformer. You can use the following formula: N = (Voltage Source) / (Turns per Volt) To get started, you will need to know the voltage source of your transformer. This can be either an AC or DC voltage. Next, you will need to determine the number of turns per volt. This information can usually be found on the datasheet for your transformer. Once you have these two values, you can use the formula above to calculate the number of turns needed for your transformer.
@freeenergytransformer5842
2 жыл бұрын
Transformers are not in mainstream technical books. We will share with you how to generate free electricity with transformers. Transformers are devices used to step up or step down the voltage of an AC current. Transformers work by transferring energy from one coil of wire to another. This is done by using a magnetic field. The AC current flowing through the primary coil of wire creates a magnetic field. This magnetic field flows through the secondary coil of wire and creates a current. The amount of current that is created is based on the number of turns of wire in each coil and the strength of the magnetic field. You can use this information to create your own transformer to generate free electricity. First, you need to create a primary coil and a secondary coil. The primary coil needs to have more turns of wire than the secondary coil.
@richardplatko7532
11 ай бұрын
An equal amount of turns would be acceptable, providing you don't mind ending up with the output voltage be in the same as the input voltage
@bBoxlearn03
4 жыл бұрын
Thank you sir for having learned so much from you
@audioelectronics542
4 жыл бұрын
Bro primary turns are always under the secondary turns but do it opposite. is there any problem to make this sequence?
@AutodidactEngineer
Жыл бұрын
Overheating
@Ashiqui-i1
2 жыл бұрын
Excellent work 👍
@prasantachowdhury4954
3 жыл бұрын
What was the value 7.5 used at start of calculation?
@cuongthao5186
2 жыл бұрын
The permeability of the steel core and the transformer efficiency of about 93% will have a coefficient of turns/volt = 7.5 🥱🥱🥱
@Its-07
4 жыл бұрын
I think you are teacher of physics and primary winding should be under the secondary winding.😀
@Tech_7665
Ай бұрын
Yes😅😅😅😅
@joshuatimothy4236
4 жыл бұрын
Always waiting for this, tx bro
@TIGER_CHEN
4 жыл бұрын
So good man👍👍👍👌👌👌
@paperjawa
Жыл бұрын
People like me can't read so narration helps a lot. It would be very easy to use a text to speech engine to do so. I read an informative article regarding how to do so. Okay thanks.
@markjustinantiquera8386
Жыл бұрын
Is it 41 + 41 in secondary turn?
@danokennethedrianp.3658
Жыл бұрын
3:35 are making the turns for 12v or 220 volts?
@imnotbeluga007
6 ай бұрын
2x 12V / 12-0-12, or center-tapped wiring. 41 turns each in his case.
@captainbabs1084
3 жыл бұрын
Really lovely video, how did you get 7.5
@iblesbosuok
4 жыл бұрын
Is formula TPV=7.5/CA for 50Hz or 60Hz mains? If the formula for 60Hz mains the transformer will burn while connected to 50Hz mains.
@bayaniconstantino5485
3 жыл бұрын
Use 6 constant for 50/60 hz.
@မာစတာသၾကၤန္
Жыл бұрын
Good jok❤❤ nice bro
@sciencefusion5352
2 жыл бұрын
This was clean Bro
@junexjeyesmallbrain3477
3 жыл бұрын
how to compute for the wire gauge need?
@mohammadorang-ojaboni4368
3 жыл бұрын
thank you for this video.
@J.GowriPrasad1970
7 ай бұрын
Turns calculation ok. But how to select wire guage for primary and secondary.
@krisea3807
3 жыл бұрын
How to calculate the output amp too? How much you got?
@donnaankstitus7092
5 ай бұрын
As shown the calculation of the core area neglects the stacking factor of typically 0.95. There are always gaps between the laminations. Turns per volt calculation confounds me. Without knowing what the max flux density of the core Bm its impossible to figure. However this lamination appears to be 24Ga which typically allows for Bm of 15KGauss..
@atsingadventure7945
4 жыл бұрын
Where did you get the 7.5 in tpv calculations? Tnx
@dazzlenconfused
4 жыл бұрын
The core area
@electrochem8819
3 жыл бұрын
If your mains voltage frequency is 60hz, 7.5 is standard.
@jeffurbano1355
3 жыл бұрын
6.25 for 60 hz.7.5 for 50hz.
@s3rkanAGA
9 ай бұрын
How do you choose the diameter of the copper wires?
@karanchowdhary5969
4 жыл бұрын
Nice sir
@chinweokigbo167
11 ай бұрын
Where did you get 7.5 from
@physicsisawesome696
4 жыл бұрын
I am from India and I like your videos very much. Subscribed
@somethingnew5496
4 жыл бұрын
Thank you for sharing dear
@pavani777
Жыл бұрын
Where can I buy the material
@immawatch6530
2 жыл бұрын
What type of tape you used ?
@mudassirarainarain2376
4 жыл бұрын
Sir ya konsa transformer ha manay inverter bnana ha us maa use krna ha
@chiragmistry1233
3 жыл бұрын
i want to know if cellotape covers winding can mutually inductance happen
@captainbabs1084
3 жыл бұрын
I guess so since it's acting as an insulating material but maybe might not be standard
@muralim9523
6 ай бұрын
Hi sir how to copper size selected sir
@vikkonstruct3686
4 жыл бұрын
This is very helpful! Thank you!
@sidamarali3030
4 жыл бұрын
Thank you. How about amperage? How can we calculate for it?
@RoadRunnerMeep
3 жыл бұрын
Amperage is calculated by thickness of the copper cable I believe. 14 gauge is maximum of 5.9A, so you can either use a thicker gauge to carry more amperage, or a multiple of thinner gauges. Say for example 10# Wire it may carry 30A, and a 14# may carry 5A. You could use 1 x 10#, or 6 x 14#
@sidamarali3030
2 жыл бұрын
@@RoadRunnerMeep thank you
@alfredterprey6677
Жыл бұрын
@@RoadRunnerMeep but how does he tell which gauge of wire to use after getting the number of turns for both primary and secondary sides
@Tech4mukesh
4 жыл бұрын
🌟Good job🌟
@KunalSingh-cv9qd
4 жыл бұрын
How did you know wire gauge?
@clashcr6780
4 жыл бұрын
what is the function of laminated steel, can you explain?
@somethingnew5496
4 жыл бұрын
nice question... soon i will make it a video on it.
@letsdoitraww
2 жыл бұрын
Standard laminations are 0.35 mm thick lamination with 3% silicon. Use of lamination is to reduce the Eddy current and silicon is used to reduce hysteresis loss.
@richardplatko7532
11 ай бұрын
Thank you for that information. I was lacking that
@PateaPatea
4 жыл бұрын
Answer me where do you buy
@javanpannadi
3 жыл бұрын
What happens if. We skip the ferrite core lamination .?!!?
@gemunujayasinghe618
3 жыл бұрын
Use heat resistant paper for isolation. Thank you.
@jackrobin8801
Жыл бұрын
In finding the gauge of wire it depends on the POWER CAPACITY of the CORE, 1st ---you have to Find the CORE Power 2nd. - Ip= primary current Ip= P/V then you have to find the e corresponding gauge of Wire base on the current- See TABLE Wire
@physicsisawesome696
4 жыл бұрын
Sir, please reply what is the amp?
@somethingnew5496
4 жыл бұрын
Amplification is a process through which we can enhance the signal amplitude or voltage or frequency. Ampere is the unit of current, ampere is defined as how much charge passing in one second from certain point. 1 ampere = charge/time.
@richardplatko7532
11 ай бұрын
LOL I think meant the amperes of this Transformer
@chuck6753
Жыл бұрын
How to decide the wire AWG of output current?Thanks
@timothymumau3515
4 жыл бұрын
Excellent
@jackrobin8801
Жыл бұрын
Not a Complete FormuLa in EI transformer CalcuLation, How do you Solve for CORE Power Capacity, and how to Get the exact size of Wire for Primary and secondary 7.5 constant Value is used for 50hz frequency and not for 60hz
@runbou3019
3 жыл бұрын
ល្អ good
@warleribeiro5648
4 жыл бұрын
Good
@ThalesPo
2 жыл бұрын
What happens if you don't apply the masking tape between windings?
@kamisama9715
Жыл бұрын
you will burn your house down
@ThalesPo
Жыл бұрын
@@kamisama9715 why?
@kamisama9715
Жыл бұрын
@@ThalesPo if due to heat/age the thin insulation between the winding breaks down, the inductance lowers and the transformer pulls more current. heats up, more insulation goes and eventually sends 220 volts into whatever devuce you're powering with the transformer and it explodes and catches fire
@tech4green
8 ай бұрын
😍😍👍👌
@fightinggamer9450
Жыл бұрын
Insulating tape name ?
@mantraders
3 жыл бұрын
Output Volt 6 , 5.5 ,5 , 4.5 , 4 3.5 , 3 , 2.5 , 2 , 1.5 , 1 800 Amp Output Men Sirf 4 Trun Dal Skty Hen Loop Ni Nikal Sktey Hen Primery Men i kuch Kr K Volt Kam Kr Skty Hen Koi Formola Hay Is Ka
@MuhammedsWorlds
4 жыл бұрын
bravo bro
@vijaymaism
3 жыл бұрын
How gauge selected...???
@adeshinaajibola5114
2 жыл бұрын
Pls how did you get 7.5
@المخترعاليمني-غ3ف
4 жыл бұрын
good luck
@kishanbhalariya5144
4 жыл бұрын
How to calculate size (Diameter) of copper winding?
@lakshmananr9963
4 жыл бұрын
It's depends on ampere what we needed in the output bro
@kishanbhalariya5144
4 жыл бұрын
Please give Equation
@JustForFun-mn2sc
4 жыл бұрын
-Watch and BLESSED !"LORD JESUS CHRIST IS THE ANSWER"PINAGALING NG DIOS NA BUHAY! kzitem.info/news/bejne/pZCt3X1trJd0jH4
@vishaldevganLove
4 жыл бұрын
The primary turn is always started in the beginning and in the secondary turn last but you have done the opposite, brother, the transformer will burn .....
@sidamarali3030
4 жыл бұрын
Why?
@richardplatko7532
11 ай бұрын
As long as you have your calculations right I don't think that would matter opposite direction of the other that would be crucial
@Myamazingdiary
4 жыл бұрын
How to choose swg?
@surendrakumarsharma6506
4 жыл бұрын
i could not understand that 1.2mm copper wire size how slected pl. explane.
@souravnandi1176
4 жыл бұрын
From Wire gauge
@m1983n1
3 жыл бұрын
Copper size how calculate
@renrenren60
4 жыл бұрын
Please let people know where to get cores? It so hard to find a retailer.
@EducationTechnicalGrowth
4 жыл бұрын
go to electronics market.
@imnotbeluga007
6 ай бұрын
Salvage from other transformers. It's hard to get bare electrical steel sheets or the E,I pieces. And you may just rewind an existing secondary like me and be happy with it. Not to mention, if you mess something up in the primary side, your primary could burn up.. which would short mains power straight to the core..
@tapasbera3754
4 жыл бұрын
What is Ampere this transformer
@rn3rav674
4 жыл бұрын
А что в ручную мотаем ? ЛАЙК конечно ,но 21 век всё-таки .
@ГришаГапон-д5ц
4 жыл бұрын
RN3RAV, потому что токарный станок.
@narendrakhona1168
4 жыл бұрын
NEED FORMULA TO CALCULATE MAGNETIC COPPER WIRE GAUGE FOR CURRENT OF PRIMARY & SECONDRY WINDINGS OF A TRANSFORMER.
@Labhabhai95B
5 ай бұрын
सर इस मे टन कित ने डालाहे बताये
@bitsurfer0101
2 жыл бұрын
Please buy a voltmeter with proper test leads
@eldiablo8890
Жыл бұрын
Lors de la calculation comment avez-vous ce 2x1.1
@vihindujayawardena2905
4 жыл бұрын
Is 7.5 is a constant value. Pls reply anyone who know. Pls pls
@AHC20
3 жыл бұрын
7.5, 8, 8.5, 9, 10
@ddbrothers5718
2 жыл бұрын
Normally we are Primary winding first on bobbing you know
@bayaniconstantino5485
3 жыл бұрын
7.5 is the constant.
@soyargentino269
4 жыл бұрын
Faltó la prueba del bombillo en el primario. Saludos
Пікірлер: 219