Its quite stable as it only gives a flat strip a round shape
@ricardosantos8176
Жыл бұрын
How wide is the tape?
@razihassan5551
Жыл бұрын
@@Creative3DPcan i built it myself?
@hitathaker405
Жыл бұрын
અતીસુંદર
@AbdiasSimeon-e1n
9 ай бұрын
Please what is this machine called
@alvaliable
Жыл бұрын
dry the filament u got a little bit more translucent and on the layer fan a 30%😊
@ChadLuca
2 ай бұрын
How do you dry it? I also don't want it to be translucent
@fog1257
3 ай бұрын
I've built a sensor a while back which can measure the diameter in real time while the filament is moving with a precision of +-0,01mm. This can be used to control the motor speed for more precise filament. I tried thinking outside the box when constructing the sensor, the total cost is about 15€ for building it.
@brananandreu4086
9 күн бұрын
Can you share how you built it?
@brianeast403
7 күн бұрын
I decided to use an esp 32 cam to measure and compare the size of the filament being extruded against a regular 1.75 mm.
@fog1257
7 күн бұрын
@@brananandreu4086 I built a mechanism in which the filament is extruded between to roller bearings. One bearing is fixed and the other is attached to a linear "rail". Above it there's a load cell which it pushes against, the thicker it is the harder it pushes. With some short code it is possible to translate this data into the diameter of the filament.
@brananandreu4086
6 күн бұрын
@@fog1257 interesting I’ll try to figure that out
@fog1257
6 күн бұрын
@@brananandreu4086 I can send you a picture of it and even files, but not straigth away. To busy with other things :/
@yamunap4686
5 ай бұрын
I think it's best way to recycle plastic bottle
@tsgfra3377
Жыл бұрын
Wouldn't it be simpler to grind the bottles and make them enter the extruder differently? This way you would have a single filament more easily without making one bottle at a time
@Creative3DP
Жыл бұрын
It's a good way to do it but it's not simpler as you have deal with extrusion speed and proper diameter ,moisture, grinding etc. It involves lot of process and is Expensive, On the other Strip to filament is easier to do
@leito8648
16 күн бұрын
Wow, nice idea
@brananandreu4086
9 күн бұрын
What kind of settings did you use for this filament beyond the temps?
@yaabop1
8 ай бұрын
Nice, liked and Subbed. What temperature are you using to turn it into filament? And what temp you printing at?
@MrAsboxe
Жыл бұрын
When you put in the cutter .... The bottle need to be heated first to let her little softer or you bring to cut her well in normal temperature?
@krushnalohar3283
5 ай бұрын
Can you tell me nozzle diameter and pet filament material thickness?
@syedsuleman-lv1lu
Жыл бұрын
Hey can you please helpme, actually i working on my minor project so i want to make that device which convert waste bottle into wire so please give me some explanation about how you make yours . Thanks
@Creative3DP
Жыл бұрын
Sure, I have created a whole tutorial on this Channel you can check that out
@JudeKisielnicki
Жыл бұрын
The print that was showed first was stringy and totally different than the second one but overall it is pretty cool
@just888why
Жыл бұрын
Hey I'm not really in for a huge project, I just want a simple model of this for my school, Can you tell me a how a working small model for this would work without much budget?
@Creative3DP
Жыл бұрын
I think this is one cheapest one but if you want to make it for way less, You can try with Glue gun and electric screw driver. That might work
@premium2554
Жыл бұрын
What are the nozzle and build plate temperatures???
@Creative3DP
Жыл бұрын
260 degree nozzle temperature and 80 degree bed temperature
@vk27.incorporate
Ай бұрын
Where can I get those 3d model that u print
@obigaming10
3 ай бұрын
What is the extruder called
@aymendaassi4756
5 ай бұрын
how much the temperature value settings
@sureshchinnu7490
3 ай бұрын
I need machine how to buy sir
@yaroslavkobezskyi
Жыл бұрын
That's good that you can reuse bottles like that, but... can you reuse that "masterpiece" somehow now?
@htetzaw5540
Ай бұрын
what temp is need to melt for that?
@Dr_InSain
11 ай бұрын
Is it durable? I want to make a startup in my city to recycle pet battles for street lighting
@Creative3DP
11 ай бұрын
I still doubt the commercial viability of this PET filament as quality might fluctuate but you can still try.
@julienzwiller1747
8 ай бұрын
Quelle température d'imposition
@Creative3DP
8 ай бұрын
210 Degree Celcius
@ILiveWithStories
8 ай бұрын
@@Creative3DP What is the thickness of the strip? I make 1cm but the printer doesn't take it. How many mm do you use exactly?
@Ironsmithwins
Жыл бұрын
Hello sorry, what temperature to melt filament pet? Cause 200°C it not melt, and 250° melt too much
@Creative3DP
Жыл бұрын
I do at 250° and it works well but if it's not working for you so I would recommend decreasing the temperature to 240 or 245 it might work
@Ironsmithwins
Жыл бұрын
@@Creative3DP hello, I mean from plastic bottle to filament... now I do it with success at 200⁰..it needs a very little cut and pass it through the extruder, then pull with big force. Now a question about dimension of plastic string..there is a mode to be costant in the cut? And what s the dimension? 2cm? And another question about size noozle: 1.75 mm is only good or is better a little bigger? For example 1.80mm?
@Creative3DP
Жыл бұрын
ooh, I thought you were referring to printing with PET Filament. Well it depends upon the thickness of bottle's wall. For Eg for 2-liter Coca-Cola bottle, I cut at a width of 12mm. As for the second question, I used a 2mm nozzle because I didn't have a 1.75mm drill bit, and it worked well since PET filament is slightly hollow. You can adjust the flow rate accordingly. In my case, I used 120% flow, but it may vary in your situation. You can go for 1.80 nozzle
@Ironsmithwins
Жыл бұрын
@@Creative3DP ok perfect, thank you for full answer! :) Then I will use 2mm as you, it's better for the reason of slightly hollow that you mentioned!
Shame these pulltrusion machines can cost more than a printer itself
@0O0-dm3tk
8 ай бұрын
Nah
@benniemartinez3840
2 ай бұрын
Whats this machine called
@kunal7biz
8 ай бұрын
Whats the max temp of heating element?
@shadedisplayed
Жыл бұрын
Amazing way to recycle a bottle.
@issss345
10 ай бұрын
Hi can i ask u I heard that bottle pla need 260 c to print can ender 3 v2 print it
@Creative3DP
10 ай бұрын
Its PET not Pla and yes it needs 260 degree to print atleast
@PriyaDharshini-j7d
7 ай бұрын
The machine used to melt the bottle what is the name of that ?
@StudioEzzz
6 ай бұрын
It is a nozzle that heats up, but I don't know how they make it come out like this. Can someone who knows please tell me?
@NieWazne420
10 ай бұрын
What is this thing that heat the nozzle i want to buy it for the same think
@Creative3DP
10 ай бұрын
heating block and ceramic heater
@sanaasadak
Ай бұрын
كيف يمكنني الحصول على الالة احتاجها جدا للعمل والدتي تحتاج لي
@SunnyIsais
Ай бұрын
how can i find the stl file for the bottle cutter
@aousbhk409
11 ай бұрын
Can I change the bottle to a silicone phone case?
@Creative3DP
11 ай бұрын
No, silicone requires a very high melting temperature or even to deform and can't be printed
@-..Foxy..-
9 ай бұрын
tutorial?
@studiotomas6657
Жыл бұрын
Can i ask how thick is the pet strip u cut from bottle? (thy for respone)
@Creative3DP
Жыл бұрын
depend on wall thickness, for this Sprite bottle i cut it into 10mm strip
@CBKCUSTOM
9 ай бұрын
what the temperature settings?
@thibaultgauthier3365
10 ай бұрын
How did you manage tu get a hot enought pour pet on an ender 3😊
@Creative3DP
10 ай бұрын
Ender 3's hotend can reach upto 260 Degree Celsius. Which is hot enough to print with it
@eagle3335
Жыл бұрын
Can u give me the Arduino code?
@novygaming5713
3 ай бұрын
Instead of wasting time and energy cutting the bottom off dozens of bottles manually just to make a usable amount of filament, you can instead glue sandpaper on a circular disk, attatch it to a motor and some gears, secure the whole system on a solid surface, and sand the bottom much more cleanly and consistently. All you have to do is press the bottle down on the sandpaper and watch as it does its thing. You can even salvage the dust for further recycling.
@bencemaldrik7555
Жыл бұрын
Hi dose ender 3 max neo support this filament?
@Creative3DP
Жыл бұрын
every 3d printer support this filament
@bencemaldrik7555
Жыл бұрын
Thanks
@currycel470
Жыл бұрын
"3D printed masterpiece"
@LatestTopFive
10 ай бұрын
wow Amazing
@lillydesign1523
Жыл бұрын
Sorry can I have the machine name? I need it!
@Creative3DP
Жыл бұрын
Its a diy machine. available on cults3d - cults3d.com/:1184966
@TDPro1
Жыл бұрын
3d print file pls for the bottle cutter
@Creative3DP
Жыл бұрын
I will soon release the file for the bottle cutter separately.
@BurhanDemirhan07
Жыл бұрын
where can i buy the bottle cutting blade and heat machine?
@mohanvithalrmathmath8373
11 ай бұрын
How to purchase machine
@Creative3DP
11 ай бұрын
its a diy machine but you can download the stl files
@HaticeYAVUZ22241
Жыл бұрын
I wonder if it can be made into a plastic bottle again . Its usefull
@Dijtra-px9vm
10 ай бұрын
a smaller one maybe yes
@amitapareek5388
Жыл бұрын
Amazing
@b-mo5696
Жыл бұрын
U should have printed another bottle, would have bin funny
@yaroslavkobezskyi
Жыл бұрын
Smart
@uae2957
8 ай бұрын
files ??
@clydesdalem.8943
8 ай бұрын
Not sure about this one
@jyjy163
6 ай бұрын
Super as tu un profil d’impression à partager je suis sous cura
Пікірлер: 104