Always good to see your productions again. Thank you Tyler.
@outboardst.comoutboardspec8631
Жыл бұрын
Thanks!
@raybrown1954
Жыл бұрын
Tyler, excellent content with the video and the follow up replies re. left hand drill bits and 6 mm helicoil kits. Thank you. Keep them coming.
@randykane474
Жыл бұрын
Thanks Tyler. Videos using flame are hard to find. They are very useful to the new DIY folks.
@outboardst.comoutboardspec8631
Жыл бұрын
Thanks, yes, when properly used, these little torches can really help out with these jobs. MAP gas is my go to for this kind of work. Oxy-Acetylene has its place in the world but is usually not necessary for trim tilt work.
@The12volts
Жыл бұрын
Wish I knew I could do this last year. I broke multiple pins on the tool. It just wouldn't budge. So I bought the air hammer tool. One way or another its coming off this year.
@williammcnulty5824
Жыл бұрын
Air chisel takes them right off and it’s worth replacing the whole cap and seals
@SDADDYWSL1TR3Y
Жыл бұрын
No it doesn’t mine are still seized up not moving at all maybe I will try heat first
@raybrown1954
Жыл бұрын
Thank you Tyler, good topic. If you have a chance a similar video on removing stubborn stainless steel flange bolts on the 3 ram Showa PTT would be very helpful, as well as the oil gallery plugs. I had a very tough time with both on my DIY F150TLRC PTT complete overhaul. Just about every bolt broke even after hours of coaxing with heat and penetrating oil. It was a nightmare. Nice overhaul stand!
@outboardst.comoutboardspec8631
Жыл бұрын
All of these 6mm bolts are going to seize. Invest in a good set of hardened left hand drill bits and 6mm helicoil set. They will make short work of drilling, tapping and setting heli coils
@outboardst.comoutboardspec8631
Жыл бұрын
Same goes for the larger bolts
@tyyoung3698
Жыл бұрын
Tyler, great video. Short, sweet, to the point. Thank you! Qq on freeing up the tilt locking pin on an old ('91) 200hp 2stroke -- the one the tilt piston attaches to at the top. You think penetrating oil, picking out the rusted circlip, then heat on the bracket would be a good way to free up the pin so I can hammer it out ?
@outboardst.comoutboardspec8631
Жыл бұрын
I have never understood why some of Yamaha Tilt Pins remain in perfect condition for decades and some of them seize badly. To answer your question: I;d try an air hammer first if you have one Removed the circlip however you can. Obviously it will be spring loaded and will launch directly at your eyes when it breaks free, safety glasses are a must If the pin is seized into the midsection often the nylon bushings are to blame. The torch is a good idea, it will heat up the midsection as well as melt out the bushings and that alone may be enough to get the pin moving. If not, and I have had several that were fused into place, youll need to cut the pin into sections by using a metal cutting blade or cutting wheel and cutting at the junction between the edges of the tilt pin mounting ring and the midsection. Once the tilt pin is cut, you can removed the trim tilt assembly, or at least get the tilt rod out of the way. The small disc shaped sections of the mounting pin that are still stuck into the mid section usually hammer out pretty easily once every thing else is out of the way
@raybrown1954
Жыл бұрын
Question about the check balls in the PTT oil pump shuttle valves and valve sub assembly, Yamaha engine F150TLRC, SHOWA PTT assembly 63P-43800-00-00, 3 ram SHOWA: this stack up uses two each of two different part number check balls: 64E-43858-00-00 upper location, and 72X-43858-00-00 lower location. What is the difference between the two part numbered balls, and are they interchangeable? I failed to take note of their location during disassembly and have lost (2) to the Land of the Missing Tiny Parts! I have ordered new check balls (about $3 each so I have factory p/n on the parts bag but delivery is way out there due to back order. The dealers do not have this information re. dimensions. The (2) balls I have are 3.16 mm (1/8"). Thank you for your help on this one.
@raybrown1954
Жыл бұрын
Tyler, this may help folks ID the check balls in the SHOWA 3 ram PTT used on my F150TLRC: 6E5-43858-00-00: 5/32" (1) required for valve seat (return oil to pump housing) 64E-43858-00-00 1/8" (2) required, for pump shuttle valves 72X-43858-00-00 3/16" (2) required, for pump main valves 64E-43858-00-00 1/8" (1) required for up relief valve (same ball used in pump shuttle valves The ball part numbers are off of new Yamaha OEM parts that came in marked bags, measured with digital calipers. The check balls used in the Tilt Piston Subassembly shock relief valve do not appear to have stand alone part numbers as that valve is part of the Tilt Piston Subassembly 63P-43810-09-00. I failed to measure these check balls. Next time!
@smalldog221
5 күн бұрын
size of the balls..
@user-fz5ge5nt5n
Жыл бұрын
Thank for the nice video, where did you get that trim unit holder?
@outboardst.comoutboardspec8631
Жыл бұрын
We have the holders fabricated and we sell them through the website. This particular rack is excellent because the V6 PTT is a challenge to work with once it is removed from the transom bracket. It's also really good to be able to turn the PTT on it's side for drilling out damaged bolts. outboardst.com/product/yamaha-tilt-trim-work-rack-ost-0352/
Пікірлер: 18