mine just arrived yesterday! Good quality at a fair price!
@Dave-in-France
6 жыл бұрын
That would be a great product for the increasing numbers of MT-07's now on the road, to complement your new exhaust !!! The exaust is terrific btw !!!!
@ericmilligan3
2 жыл бұрын
Great idea, I’ve just ordered one for my Street Twin, however, if you haven’t got an extended 27mm socket you’d have to take it off to slacken the spindle nut.
@stevenhill6214
7 жыл бұрын
Now why didn't I think of that?....brilliant idea!
@MrStingraybernard
5 жыл бұрын
just bought 1 , looks to be nice quality
@davidschwartz9636
5 жыл бұрын
This is a good idea, and I could really do with one of these to fit my triumph tiger 955i. - Do you do one that will fit my bike??? Thanks David
@jonathanprince2218
4 жыл бұрын
I have one to install they manufacturer instruction suggest applying 'red grease' along it before install, any recommendations on a good grease I could use for this and other areas of bike?
@arjuckes
5 ай бұрын
I got the Triumph Bobbins for my Bobber and an Oxford Paddock Stand, trouble is the bobbins are mounted to low so it's a dodgy business levering it up. This solution going through the axle looks like it should be much easier.
@tommcneill2995
2 жыл бұрын
I purchased the bobbin kit from TEC Bike Parts USA for a 2017 Street Cup. If you screw the left side with the collar all the way end it is too short and no threads are exposed on the right side. I can screw both sides only halfway and make it work but don't feel like it is secure and wish the bolt were longer.
@davidsantiago-ji8fi
2 жыл бұрын
Same issue with a street twin. The bolt all the way on the left collar side make the right side short. Then trying to figure out how to get even amounts of thread on each side isn’t as easy at it sounds. And finally the left side isn’t easily able turn.
@billbellart
6 жыл бұрын
Fine and easy job, the spindle was about an inch over length, but cut this down and fits fine.
@lanner1361
7 жыл бұрын
I'm assuming you cannot remove the wheel with these installed. Only for working on chain and general maintenance?
@MpDay
7 жыл бұрын
Does it also fit on a Thruxton 900? I'm looking for the same sort of solution, like this one.
@andrewdavies9167
2 жыл бұрын
Do I need to grease the spindle before fitting?
@robycash1185
7 жыл бұрын
Hi is the fender in the video an original Fender Removal Kit? how did you install the licensa plate in that position? thanks
@ericb252
6 жыл бұрын
Roby Cash did you figure it out? I'm curious too
@danielhiller4978
2 жыл бұрын
Do you make one for a 2020 Triumph Bonneville T100? If so can I please get a part number? Thank you
@dustytriumph
Жыл бұрын
This looks awesome! But.....will the stock exhaust be in the way to use a paddock stand?
@maxvij
Жыл бұрын
No it will not, the stock exhaust are a bit higher, the paddock stand does not touch them.
@dustytriumph
Жыл бұрын
@@maxvij Thank you👍
@macumuzahn
2 ай бұрын
My Thruxton 900 2004 does not seem to have a hollow axel, am I being thick or di I have to remove loxk nuts etc , TIA. Mark
@luigidicintio5999
3 жыл бұрын
hello where can i download a streettwin 2021 repair manual?
@RicardoSilva-qp4bb
7 жыл бұрын
Not entirely related but those are some nice looking rear view mirrors. Do you mind telling me what brand they are? Thank you.
@TECBikeParts
7 жыл бұрын
They are a sample I was sent and we are testing them out ,we will probably be selling these on our site early next year
@RicardoSilva-qp4bb
7 жыл бұрын
Ok, thanks for the quick answer. Nice looking ones on the Street Twin. Might have a look at them in the future.
@luxurybargainph
Жыл бұрын
Nice. Will this also fit on speed twin 900?
@Nate-Dawwg
3 ай бұрын
I would like to know this as well. I have a 2023 speed twin 900.
@mitch9838
7 ай бұрын
does anyone know if this will fit on a 2024 street scrambler 900?
@philtedman4730
3 жыл бұрын
how much for a st 1050 2006 , bobbin bar .
@phillydra9823
4 жыл бұрын
is there anyting to stop me using a long bit of threned bold or 10mm metal and just popping it up on the stand with that?
@TECBikeParts
4 жыл бұрын
You could ,but bike would lean over as the axle is different diameter internally at each end , hence why the bobbins are stepped
@phillydra9823
4 жыл бұрын
@@TECBikeParts good explanation thanks
@nellaRissa
3 жыл бұрын
do you have a ebay store?
@Minorstunt
5 жыл бұрын
Hi guys just ordered on eBay from you, once in place do you leave it fitted or take on and off when needed? Cheers
@TECBikeParts
5 жыл бұрын
Hi you can leave in all the time and recommend using locktite on the ends. only need to come off if fully removing wheel
@amotorcyclerider3230
5 жыл бұрын
Can you post the link to where I can buy it? that steel rod and the bolts (bobbins)
@MichaelJepson80
5 жыл бұрын
@@TECBikeParts Can you still get it off after applying loctite? And what loctite would I use?
@georgemilburn6213
5 жыл бұрын
@@MichaelJepson80 not a problem if you use BLUE loctite, don't use RED loctite as this is very hard to get off.
@RamboMT1
7 жыл бұрын
Thanks. Just fitted to a Street Cup, took seconds.
@amotorcyclerider3230
5 жыл бұрын
Boss, can you let me know where you bought it and the link please? Does it come with the rod as in the video and you just insert it and bold it both sides?
@davidcooper6704
5 жыл бұрын
Can the bobbins be left on whist riding the bike?
@TECBikeParts
5 жыл бұрын
Yes just leave them on
@kjltube
5 жыл бұрын
@@TECBikeParts Should I apply some thread lock to keep them secure?
@mcplutt
2 жыл бұрын
No loctite then?
@detroitdizzle5513
7 жыл бұрын
Will this work on a T100?
@TECBikeParts
7 жыл бұрын
Hi you do not say if air cooled or new gen watercooled ?anyway will not fit older air cooled bikes,but we will be making one for them soon.On new gen T100 it will foul the stock silencers but OK with aftermarket cans
@detroitdizzle5513
7 жыл бұрын
TEC Bike Parts Thanks I have an air cooled T100
@TECBikeParts
7 жыл бұрын
Kit for air cooled T100 should be available early next year
@detroitdizzle5513
7 жыл бұрын
Nice thanks for the reply
@davidsantiago-ji8fi
2 жыл бұрын
Bought those and installing like the video doesn’t work. The bolt is too short you can’t tighten all the way on the left side because it just loosens the right and bobbin falls off. You can probably just find a long metal rod to slide though and use it when needed. Oh well there goes 70 bucks
@rosstisbury1626
4 жыл бұрын
what a great idea . . . but dammit my 2008 Scrambler doesnt have a hollow axle . . Bum !
@TECBikeParts
7 жыл бұрын
Special intro webshop price on these £39.99 see tecbikeparts.com or tecbikepartsusa.com for N.America
Пікірлер: 55