I just subscribed to your channel.. Thanks for the great tips .. I got a free ego Ln2100sp which will propel but the lights don’t come on hoping it’s the fuse .. I have a lm2000 and another lm2100sp… so this is my project mower
@sarahe4120
Ай бұрын
My EGO LM2102SP lawnmower started making a rough noise and won't run. I had just finished cutting the front lawn and took it to the back when it started doing it. Battery is fully charged.
@emahpour
2 жыл бұрын
Mine runs and randomly stops after some time. While shutting off pulling the mower back so back wheels spin makes it start again and continue. What seems to be the issue ?
@johncross436
Жыл бұрын
in the self propel board check you are testing the red and black from the board?? I ask because you then test the black from the plug to the same black wire as before but comment it is the black going out to the motor ( do you mean it is the black wire connected to the board that goes to the motor) - were not testing the wire coming off the motor except to hit it with a charge to test the motor???
@jbctboncal3920
Жыл бұрын
I see I can order the PCBA for my LM2100sp but is there a video showing how to replace it?
@matterwin8635
2 жыл бұрын
Printed circuit board assembly. Any of the controllers are called pcba or electric assemblies.
@tln8424
Жыл бұрын
Great video what is the PCVA?
@pjshooter6
2 жыл бұрын
I have an issue with mine. With the blade installed, and the handle is pulled, the motor will come on for a split second, then shut off and the orange light flashes fast. If I remove the blade it runs fine. I assume it's the overload sensor, but I cannot figure out where that is located
@matterwin8635
2 жыл бұрын
that sounds like the main pcba is failing.
@faygopop8797
Жыл бұрын
Did you find a solution? I have the same issue. I took my blades off to sharpen them and after I put them back on I have to pull the handel several times for it to start up. Like it is on too tight or something.
@pjshooter6
Жыл бұрын
@@faygopop8797 nope replaced the mower
@johncross436
Жыл бұрын
what set up for the dc power supply VOLTS AMPS ETC -
@feldredge5077
Ай бұрын
HE says 5 volts early on not sure if that's for all diagnostics never talked about amps...
@garyf3470
9 ай бұрын
At about 1:30 you show how to test for a short in the switch assembly and that if moving the handle turns it on, to replace the switch assembly? But which switch? Isn’t there one for the handle position, one to make sure the handle is fully extended, one for the bail, and one for the green button? And are there instructions for replacing it?
@matterwin8635
9 ай бұрын
We generally do the whole switch assembly that replaces all the wires. The part cost is low enough that it better to do that the fox one wire say in the selfdrive then few week later wire in the blade side brakes from same stress factor. There is a video on here to show the removal and reinstall of that part.
@garyf3470
9 ай бұрын
@@matterwin8635 Thanks very much. I think I found that part but it appears to be out of stock at Ego’s retail parts vendor.
@anthonykent8561
6 күн бұрын
Great VIDEO! Batteries, Fuse, PCBA's, relays and wires all checkout, and blade spins freely by hand but NO POWER (lights, cutting motor, SP). Any other tips?
@matterwin8635
5 күн бұрын
with no power it is likely the main pcba
@anthonykent8561
4 күн бұрын
@@matterwin8635 The main PCBA passed the troubleshooting steps (was in spec) in the video. Could it still be bad?
@matterwin8635
3 күн бұрын
@@anthonykent8561 sadly yes lol but if you have no power not even headlight i'd say main pcba.
@Dcalzaretta
Жыл бұрын
My self-propelled stop working. EGO is replacing the entire mower.
@johnmellyn2700
Жыл бұрын
Hi Dan,… how did you get them to do that,… my self propelled only works in slow, when you push the speed lever forward nothing happens ( and the slow speed is so slow it’s not even worth using because it’s about 1/4 of walking speed )…. So frustrating for an old coot like me whose already had one heart attack and really don’t want another one .
@jamesryan3054
2 жыл бұрын
What is a PCBA
@Cameroner1
2 жыл бұрын
Printed circuit board
@joeshmoe7789
11 ай бұрын
Diode mode doesn't measure volts.
@matterwin8635
11 ай бұрын
Hmm guess that depends on what you are talking about. It use the volts from the meter to test giving you the results in a voltage reading. So when I say the voltage should be I am talking about what it will say on the meter. So ya voltage reading
@joeshmoe7789
11 ай бұрын
@@matterwin8635 Your meter is reading 0 ohms, not volts. Proper way to test a fuse is to remove at least 1 end from the circuit. How can you have voltage with the battery removed? 1:05
@MilkieBeargames
Жыл бұрын
My fuse is dead
@matterwin8635
Жыл бұрын
i am sorry to hear that. lol the fuse is replaceable though you do have to use waterproof connectors.
@MilkieBeargames
Жыл бұрын
@@matterwin8635 I replaced my fuse. Then my ego lm2100sp started smoking, so I took the cover off so I could see what was going on inside. And I could see flames coming from the motor. The smoke was very thick. Should I keep investigating this or give up?
@lindaberry3698
6 ай бұрын
@@MilkieBeargames
@tln8424
Жыл бұрын
I mean PCBA
@matterwin8635
8 ай бұрын
printed circuit bored assembly
@marylynnames500rrr
11 күн бұрын
For the price of the mower, I expected more, as in not needing special diagnostic tools. Actually expected a well-running mower for several years. I recommend NOT buying this POS mower.
Пікірлер: 39