For people asking, the bit is 5-sided, so an Allen wrench won’t work.
@tjmattingly33
5 жыл бұрын
Can't make it easy and cheap, sigh.
@NemoNepersonne
4 жыл бұрын
I saw an ad for these on Facebook. $30! And the ad doesn’t mention that these can be used only on certain prepared TroyBilt engines. It says ANY gasoline engine. But NOT on my Husqvarna weed whacker or my Stihl chainsaw. Thanks for saving me money.
@clwest3538
5 жыл бұрын
know this is an old post, but wanted to thank you for posting. I bought a Troy on sale (long time ago) and got this little bit at the same time ... but with 'guys' around I never used it until today. With no guy to pull and my bad back ... well this saved me!! Thank you for showing how easy it is to use - mine worked like a champ!!
@a1930ford
2 жыл бұрын
I have rheumatoid arthritis and I have done this mod on virtually all of my equipment with a pull start. It works great and doesn't kill my arm, other than my DeWalt drill is fairly heavy to hold.
@patrickmcgrath2533
2 жыл бұрын
My work around the pentagon was to use 1.25" of 1/2" square steel bar, pop that into 1/2' drive socket which fits the nut on the engine. Chuck the socket and 1/2" bar into a lathe. Drill out the square stock with a 6mm drill. The pentagon fits snugly in the 6mm hole. Drill and tap a hole drilled on one of the sides of the square stock to take 4mm grub screw to secure the stock onto the pentagon shaft. If the socket has a tendency to slip off the square stock, put a grub screw on that too. Then away you go.
@acpropulsion6191
Жыл бұрын
Sir this is a $9 part lol
@josephpang6207
Жыл бұрын
Hope this better than the Rachet adapter which did not turn follow clockwise and loosing the nut on the motor. The nut got flown away after starting motor. Thanks. Another senior appreciate this video. Bought this and hope will turn start my outboard 2 strokes motor on kayak.
@dragynnmagickk7332
3 жыл бұрын
Just bought this bit yesterday and I'm excited to try it, because pulling the string to get it started is bad on my arm.
@jeffstanley4593
5 жыл бұрын
I just bought one, I had a back operation and don't want to risk pulling a string. The trimmer is probably too heavy to lift but I am going to try it anyway. I have had good luck with Troy Bilt.
@acpropulsion6191
5 жыл бұрын
Hi Jeff. This trimmer has been tough, but unfortunately I think she’s about to kick the bucket. Starting to knock and leak oil. I went out last week and bought a Kobalt 40v battery powered trimmer. I really like it. Keep that in mind to avoid pulling a string. BTW I wish I would have got the 80v.
@ellefont3813
6 жыл бұрын
I been trying to find the diameters for a while now. Thanks for mentioning it in your information.
@JasonsAustraliana
6 жыл бұрын
I have been looking to find out the socket size in the crankshaft. In the video, he says 3/8 & 5/16, which is it? Someone mentioned it was a 5 sided socket, do you know if that is true? I was hoping to use a broken allen key.
@Mmmyess
5 жыл бұрын
@@JasonsAustraliana Spend the $10 and get the widget from Lowes. The one-directional bearing is critical, NOT to stop you from cranking the engine in the wrong direction but to stop the engine from destroying your drill if it takes off and you can't pull the Allen wrench out in time.
@michaelrevoire2266
8 ай бұрын
I have one of those and it works great. Wish it could also be used on my backpack blower and chainsaw.
@immrnoidall
3 жыл бұрын
for every other pull start motor , get, " Performance Tool W32114 1/2" Drive Ratcheting Adapter" , $15 on EBUY. you will need to take the pull start off. just a few screws. just get a small cordless drill and bring it with you ,if it stalls out somewhere.
@victork3397
3 жыл бұрын
Where did you find it for $15? Post the item number
@immrnoidall
3 жыл бұрын
@@victork3397 yup. 15 is the cheapest. to use it on a drill or screw gun you will need a 1/2 in, male, to screw gun bit adapter. and whatever size socket for the nut on your flywheel. these troy built trimmers, have a hole built in to the center of the pull start/flywheel cover with an odd size that will take only "their" ratchet thing and start motor. other trimmers will need to be modified to get at the flywheel nut. you can just use a drill but the ratchet thing is safer . so the drill doesn't kick back when an engine starts up , but you didn't get it off the nut in time. .there are lots of videos about it. it works. just paste Performance Tool W32114 1/2" Drive Ratcheting Adapter into ebay search. I tried to leave a link to it but youtube would not let me.
@josephpang6207
Жыл бұрын
Rachet adapter did not follow turn clockwise. It got locked up counterclockwise and got the nut on motor flown away removed. Rachet adapter not good suggestion.
@jasoncessna2522
3 жыл бұрын
I wish I would've watched this 4 years ago! I'm going to but a Dewalt tomorrow! Done with gas!
@acpropulsion6191
Жыл бұрын
Me too. I bought a Kobalt
@pennyminkkinen7201
3 жыл бұрын
Thanks for this, we have troyblt little cultivator and have been looking for just this to get the thing started
@acpropulsion6191
Жыл бұрын
Glad I could help
@edgarroman5913
5 жыл бұрын
Thanks bro. U saved me from buying a new one
@juans6639
9 ай бұрын
Thank you for the excellent video
@WarriorDudePerson
2 жыл бұрын
I've got that same drill. Thing is a beast!
@Kendell062
4 жыл бұрын
I'm convinced, thanks.
@js_1995x
4 жыл бұрын
Using a craftsman drill to start a troy bilt weedeater. The irony!
@roy-ld3dg
2 жыл бұрын
I was careful using it, and It stripped after 2 or 3 starts, sorry to say.
@gtdodgeviper
5 жыл бұрын
Those bits break very easy
@jaybraun9113
4 жыл бұрын
I tried one of these. Directions say that drill has to run at 1000 rpm. Mine was 750, and it wouldn't start my trimmer. Sold it to neighbor who had a faster drill.
@acpropulsion6191
Жыл бұрын
That drill in the video ran at 800rpm. Craftsman Bolt-On.
@alexreese1914
6 жыл бұрын
Thanks for showing me I appreciate it.
@stevenwhitaker9520
Жыл бұрын
I have a troy built weed eater with jumpstart on it
@tiffanyhupp3285
6 жыл бұрын
Thank you!!
@brianbray2721
2 жыл бұрын
Mine don't have a choke on it. I put a long Allen wrench in my drill to crank it
@arabiantxn
5 жыл бұрын
No a Handyman by any means, but I do have a question, Do you think as long as we can if we can some how modify other brands of weedeates by welding a washer or some sorta socket that will accommodate the fitment of that tool to spin the motor in the direction of rhe engine crank we should be able to use this tool with other weedeaters as well right 👉
@arabiantxn
5 жыл бұрын
I don't know if it's possible or not I want to get some ideas to the feasibility of it
@kirkb2286
2 жыл бұрын
Will this work on any weed trimmer
@mattdooley6206
3 жыл бұрын
What’s the name of it
@terrynoble8662
2 жыл бұрын
I've been thru 4 of these! They are junk! The tool either breaks or turns in both directions!
@JasonsAustraliana
6 жыл бұрын
What size is the socket in the crank and how many sides does the key/socket have?
@guyhorton9296
2 жыл бұрын
At least yours runs. Mine hasn’t ran right since I bought it!
@acpropulsion6191
2 жыл бұрын
Get a kobalt battery powered trimmer. Never going gas powered again.
@a1rh3add
Жыл бұрын
They really don't. Troybilt made garbage in their later years. From the factory mines been a pita to start and when I found off they want to sell a product to make it start better I was pissed.
@Jro-pk5de
2 жыл бұрын
I will get me one!
@SavNout01
4 жыл бұрын
I got one too, won't work with my impact drill tho, only my regular drill.
@fukkyoutube
3 жыл бұрын
where did you buy this because I've called every store in a 40 mile radius of where i li e and they either say they have o clue what im talking about or just say no we dont ha e it
@acpropulsion6191
3 жыл бұрын
Jump Start Drill Bit Compatible with Troy Bilt Plug Button, Jumpstart Electric Engine Drill Bit Adapter, 49MASCBP966, 2 Pack www.amazon.com/dp/B08QJ8F3BD/ref=cm_sw_r_cp_api_glt_fabc_TRVP0Q1EVGYMZG55HXF4?_encoding=UTF8&psc=1
@fukkyoutube
3 жыл бұрын
@@acpropulsion6191 lowes in my area carries then they had 20 in stock yesterday but that you for the response
@healthyamerican
6 жыл бұрын
i have this same type of trimmer, but its a craftsman. the pull rope broke. can i still do this with the crank tool with a broken pull rope? also could you suggest a video on how to fix the pull rope on this type of weed eater..ty
@acpropulsion6191
6 жыл бұрын
healthyamerican I can’t speak for a craftsman, but if the rope broke on my trimmer, the tool would still start the engine. However, my trimmer is getting old and now needs a combination of the jumpstart tool AND pulling the rope. I replaced my rope as well and I couldn’t really find a good video so I just did it with no help. It’s not terribly difficult, but it did take about an hour for me. Good luck!
@Roboticdoughbull3k
6 жыл бұрын
Look-up replacing the starter pully on a Troybuilt, by chill c. Good explanation
@fast2valve559
4 жыл бұрын
Its a damn chore to record these weedeater. They need their ass whooped for this design. I just purchased an echo srm2620 due to my rope broke in my troy bilt again
@donaldkindig5126
2 жыл бұрын
Doesnt work on my craftsman weed eater, But got one for free when I got mt blower.
@johncahill612
4 жыл бұрын
Do you think this will work if your pull string will not recoil?
@acpropulsion6191
4 жыл бұрын
Just guessing....yes it should.
@garymayer3356
3 жыл бұрын
Wow
@mattdooley6206
3 жыл бұрын
Will it work for a Stihl FS56 weed eater
@johncarlberg4481
3 жыл бұрын
No only Chinese mtd trimmers
@bobbillings
3 жыл бұрын
toro is not even making or selling 4 cycle weed trimmers anymore. they are down to just 3 models of gas trimmers, all are the same engine, all 2 stroke. but they have 8 different electric trimmers to choose from. goodybye gas powered everything eventually it seems.
@NiNjaTurtLe697
4 жыл бұрын
What drill setting should this be on?
@acpropulsion6191
4 жыл бұрын
High speed
@NiNjaTurtLe697
4 жыл бұрын
@@acpropulsion6191 thanks but is that the drill mode?
@acpropulsion6191
4 жыл бұрын
R0tten not sure what you mean by “mode”, but you should have the drill on high speed, turning clockwise.
@RickyPisano
5 жыл бұрын
Can I do this with a hyper tough??
@mrblueberry3463
5 жыл бұрын
If it has the fancy starter
@js_1995x
4 жыл бұрын
Buy a craftsman speed start part and take the engine cover off and put the part on
@thebiblestudyhelper9389
6 жыл бұрын
By the time I get my Troy bilt started I won't have the strength left to do the work . If you have work to do don't buy Troy bilt gimmicks
@waltertaggart2020
5 жыл бұрын
The Bible Study Helper like
@acpropulsion6191
5 жыл бұрын
This trimmer is 8 years old. Still works. Gimmick? nah. Just gotta know what you're doing ;)
@rachelleharn8502
5 жыл бұрын
There not gimmiks think of it for old people or people with disabilities it can be very hard for them to start it this way it makes it easy for them to start it and they Can have a awesome looking lawn
@markeickmann8001
5 жыл бұрын
Mine works great, best weed eater i ever had. Make sure to empty in winter or try adding stabilizer to fuel, makes them easier to start
@thehotsinger
4 жыл бұрын
What is the Dang engine still won't turn over even with the jumpstart?😡😡😡
@acpropulsion6191
4 жыл бұрын
Bad fuel or spark plug?
@acpropulsion6191
4 жыл бұрын
I don’t even have this trimmer anymore. I went out a got a Kobalt battery powered trimmer. Works great. I’ll never go back to a gas powered.
@thehotsinger
4 жыл бұрын
I've no idea.🤷🏻♀️ I'm over it. Will return the drill bit and buy a battery one.
@acpropulsion6191
3 жыл бұрын
@@thehotsinger did you get the battery powered trimmer?
@nowthatsfunny1
2 жыл бұрын
Just buy a Stihl and you won't have any problems.
@theodorekulenics4569
Жыл бұрын
Do you think it would work on craftsman21hp. Intech ohv.tkakron Oh
Пікірлер: 82