The cutting accuracy on these is so impressive. At my place of work, the normal process for cutting our brackets is going through 3 processes starting with a shear, then onto a punch press, and then a splitter to make 2 brackets. The trumpf laser cuts the brackets so precise that it makes a super sharp edge on the brackets that actually shaves off bits of brass on the bracket welders. I'm not in that department anymore, but I've heard they're having to change the process for the final welding of the brackets to prevent having to change the brass in the bracket welders after every production run of a certain size. Our old laser cuts at about 300 in/min. Our new trumpf laser cuts at 960 in/min! Impressive piece of engineering! I put in for the job to run it, but unfortunately didn't get it.
@michaelniceguy4042
4 жыл бұрын
I ran a 3030 for 12 years and you check the center the beam at the start of every shift.and there great for doing government jobs
@jamesirvine2579
3 жыл бұрын
I assume you mean tapeshot you check it more than once
@rnicko86
3 жыл бұрын
Hello sir.. For 12 years the laser beam still stable or any degradation capacity normal?? Please answer..
@jamesirvine2579
3 жыл бұрын
@@rnicko86 as long as the machine gets regularly serviced I work a c02 trumpf 3030 manufactured in 2006 still going strong I used to work the old 3030 Bosch control one that was still going after 20 years the worst thing to happen is getting water into the resonator.
@rnicko86
3 жыл бұрын
@@jamesirvine2579 what happen the resonator on a long periode of time?
@apollokidd8273
3 жыл бұрын
I like the music :)
@galabauworkgroup8637
Жыл бұрын
I like it
@christopherstroud7389
5 жыл бұрын
always test cut with this machine....the number of parameter changes I had to make was ridiculous ...check the head and make sure its clean...dial back the speed test it
@satynar7418
Жыл бұрын
song?
@traceymills9469
8 жыл бұрын
Does this laser have the welding option?
@markovichfedor6674
4 жыл бұрын
no
@nasaruddin5779
3 жыл бұрын
No
@nasaruddin5779
3 жыл бұрын
I'm oparating one of this
@SirGipsy
3 жыл бұрын
Very good
@OmkarN
Жыл бұрын
240p quality video? really?
@draganstojanovic2997
6 жыл бұрын
You have to change and modify parameters
@nguyenlinh6686
8 жыл бұрын
máy thích quá. Mơ ước của tôi
@MeCutRadiation
5 жыл бұрын
В 2014-м году моя нокия 3310 снимала более качественно. Вот вам и супертехнологии
@inqden
2 жыл бұрын
А они камеру рекламировали, да? Я не сразу понял
@PaulMagnet
7 жыл бұрын
Das Video wurde doch in der Bearbeitung beschleunigt! Um die eigentliche Schneidgeschwindigkeit zu verfälschen.
@FirestormXTi
7 жыл бұрын
Hab das Ding schon live in meiner alten Firma gesehen, ich kann dir sagen: Nein. Das Ding ist so scheiß-schnell.
@vijaybharambe9401
5 жыл бұрын
How much price?
@RuijieLaser-kevin
5 жыл бұрын
Hi Vijay, This is Kevin from ruijie laser. Are you interested in fiber laser cutting machine? pls feel free to contact me. Whatsapp/Wechat: 0086 15662784401.
@angelbetancourt9222
7 жыл бұрын
aluminum seems to have bur all along the edges every part I cut. I don't know what the proper settings are. trumpfs settings don't work
@oleksandrmelnychuk37
7 жыл бұрын
Please contact service. It could be a few reasons. Maybe something as simple as bad pressure settings or 3rd party nozzles.
@PaulMagnet
7 жыл бұрын
Ridge means the focus settings must be adjusted.
@oleksandrmelnychuk37
6 жыл бұрын
it is also the nature of the material. aluminum will always leave a ridge more aggressive than any other material.
@Notreallyhere817r
6 жыл бұрын
It will always have a bur on it unless it is very thin aluminium. Try cutting 15mm aluminium the bur is ridiculous
@BA-wt1gl
6 жыл бұрын
I don't have much experience with newer lasers, but with an older laser after much fine-tuning my parts still needed a bit of deburr work. I think it's the reflective nature of aluminum that makes it especially difficult to cut without dross/burr. Keep fine-tuning, and good luck to you. Anything over .063 aluminum having a burr is normal. .090 or .125 thick it is well known you will have a burr, very little you can do about it.
@RajKumar-786
9 жыл бұрын
HAVE ANY JOB OF CNC TRU LASER OPERATOR
@waleedkalbouneh1295
8 жыл бұрын
how are you
@RajKumar-786
8 жыл бұрын
Good
@RajKumar-786
8 жыл бұрын
Do you know me?
@inazitoinazito1602
9 жыл бұрын
me gustaria conseguir un manual de laser trumpf 5000
@reginaldovsantos
8 жыл бұрын
olá
@reginaldovsantos
8 жыл бұрын
me passe seu email
@inazitoinazito1602
8 жыл бұрын
inakiimb@gmail.com
@abubakerosmsn5662
3 жыл бұрын
Yo también :) pero in inglés por favor 🙏 abubakeraltamih@yahoo.com Muchas gracias
@rafaelantunesdaroza231
7 жыл бұрын
trabalhei com corte a laser
@Spelter
4 жыл бұрын
If their software wouldn't be such a mess it would be awsome. But the interface system is so bad, I only can say it's broken by design
Пікірлер: 48