I really like the discman series. Even if they are difficult to diagnose,there really isn’t enough videos on laser related products and repairs. These videos really do give a good education. Look forward to seeing the rest of these discmans repaired
@thebenchmonkey4117
4 жыл бұрын
Just a little advice, don't worry about scraping the wire just run the soldering iron over it, the heat will strip the enamel off the wire. If you use a scope look up "eye pattern", diagnostic procedure to check out FE and TE (focus error, tracking error). This will give you the condition of the laser. That's how we used to do it back in the day when the values could be adjusted. Great video.
@OneTimeLiving
2 жыл бұрын
Bought a Walkman D-C20 yesterday. Had similar symptoms to yours (Starts spinning for 2-3 seconds, then stops, laser searches for something -> No Disk) I was about to give up, but then i saw the resister on the laser, it was set to 2.8kOm. Moved it down to 1.5 and it WORKED ! Thank you sir for your video and help
@GadgetUK164
4 жыл бұрын
Great job on the repair of the damaged traces =D You cannot always see the laser!!! It depends on the frequency of the laser. The fact the disc was spinning, shows it was actually detecting the disc (using the laser), but it was perhaps too low. Some CD units have a laser that you cannot see with the naked eye. Also note, if you have the laser set too high, the same thing can happen where it won't detect a disc. I also think you have to the two connectors the wrong way around, since that noise its making at the end sounds like it bobs up and down, and THEN hits the tracking coils, when I think it should be moving the sled! I noticed that when you swapped them around earlier on in the video (see around 30:00 - it focuses normally, then wobbles (tracking coils driven), when actually I think the sled should be moving!
@BCProgramming
4 жыл бұрын
CDs use light around 780nm, which is infrared. I'm not sure if a shorter wavelength works properly, as I understand it it has to do with the pitch of the pits in the reflective layers.
@Mymatevince
4 жыл бұрын
Thanks Chris for the advice, I will double check the schematics because they do show the connectors for the spindle and the sled. I will do a revisit on this one :-)
@archerchance6214
3 жыл бұрын
i know im asking the wrong place but does anybody know a way to log back into an Instagram account..? I stupidly forgot the login password. I appreciate any help you can give me!
@ledgerelon6313
3 жыл бұрын
@Archer Chance Instablaster ;)
@archerchance6214
3 жыл бұрын
@Ledger Elon thanks for your reply. I found the site thru google and I'm in the hacking process now. I see it takes a while so I will get back to you later with my results.
@patprop74
4 жыл бұрын
About the enameled coated wire, you don't need to scrape the coating off, it is made to burn off when you heat it with your soldering iron,
@HugoFaria-AZ
4 жыл бұрын
was looking for this.. xD
@markshellard5894
4 жыл бұрын
Probably refused to play the music on the cd
@wolfbitegames6011
4 жыл бұрын
I feel like your gonna hit 1 mill this year
@ovalwingnut
4 жыл бұрын
❤ the "repair @all cost no matter the value". Very CoOL.... the less traveled path. Of course experience gleaned here will be applied to future & past projects. I salute you! 👍😎
@deideloo
Жыл бұрын
really great video - had a similar issue with my discman and could not find any guides about it anywhere. i was also unable to fix it by messing with the potentiometer. your video helps keep me from doing a lot of unnecessary steps. thanks :)
@pradeepsinghrajpoot2008
4 жыл бұрын
Had a bad😥 day but u video made me feel happy 😊
@Tokaisho1
4 жыл бұрын
The shaking it has, it looks like the laser gears might be skipping when it tries to move further out, I wonder if its a mechanical issue with the laser worm wheel? Often a laser checks the disk type and amount of tracks right near the centre of the disk then the laser moves out to play track 1.
@StephenArsenault
4 жыл бұрын
Diddleshot I wonder if it’s trying to home the laser head - but because the head is all the way down it cannot move further. Vince was sliding it around without a care in the world early in the video lol
@BADSeCt0R2XP
4 жыл бұрын
@@StephenArsenault that's exactly what it is sir. i have a similar one that does the exact thing. It tries to retract the head but it cannot because t's already there but the pickup icu cant sense it. It usually indicates an end-of-the-line killswitch malfunction. The Laser is probably fine(ish).
@Sythe114
4 жыл бұрын
@@StephenArsenault I hope this one gets read because he certainly skipped the gears in the read head tracking a few minutes in. The disk info is located in a certain location and if the head can't get there it won't see the disc.
@iian0
4 жыл бұрын
I always clean the laser with meths or IPA. I have had much success with cleaning the laser of a device. However you are most likely right with your thoughts on the laser being the reason for it being put into storage and the circuit board tracks being a secondary fault..
@xbin3ryx86
4 жыл бұрын
Hopefully I suggest this so that it makes sense. But, I think when you adjusted the pot for the laser you may have went the wrong way. On a pot you have three legs, with the "wiper" in the middle. So, while the resistance goes up between the wiper and one leg, it goes down between the wiper and the other leg. So it would depend on which leg the laser was wired to. I couldn't tell from the video if it had three legs or not, but it is worth a try. The laser did seem to get dimmer the more you turned it, or maybe it was just burning it out worse...Lol.
@getyourkicksagain
4 жыл бұрын
Good observation. I also wondered why Vince did not try to turn the pot the other way to see if it made a difference.
@peterzeboroff7448
4 жыл бұрын
Hi Vince, the laser in the cd players only are all infra-red with a wavelength of 780nm which is barely visible to the human eye but looking at your video indicates that the laser diode may be okay. The dvd laser diodes operate at 650nm and are bright deep red and the Blu-ray players operate at 405nm which produce a violet light.
@Mymatevince
4 жыл бұрын
Thank you Peter :-)
@Boogie_the_cat
Жыл бұрын
Thanks. I was going to mention this, but I saw you beat me to it. One of the reasons these lasers can cause eye damage is because the human eyes are not tuned to infrared, so there will be no blink reflex when an infrared laser hits your eyes, so continuous damage may be done to the eyes without being aware of it, unlike a visible-light laser, where the victim will at least blink involuntarily after the beam hits the eyes. This is not to say that powerful lasers will not damage the eyes in the fractions of a second it takes to blink. 405 nanometer light can be the most damaging because that wavelength has a special affinity to the cells of our eyes. This is why even non-laser UV lights tell you not to look directly at them. I'm not trying to show off here, the point to take away from this digression is 'be especially careful when working on blue-ray drives (if the laser is exposed)' We all want to make sure Vince can see properly, so he can continue to make these fun and interesting videos.
@kawasakiinitful
Жыл бұрын
Hi Vince I love your videos ,you have inspired me to buy a bang and Olufsen cdx cd player which is faulty no power at all. I'm struggling with it at the mo as it keeps blowing the solder in fuse 750ma but I'll stick with it. Ps you sound like tiff needell are you from same area.? Cheers buddy Dave...
@dodgydruid
4 жыл бұрын
Was watching this whilst repairing my CybaSnipa gaming keyboard pad where over the years the carbon on the keypress grids had basically created a layer over the metal and stopped the whole thing working, so with MMV approved IPA and fibreglass brush took me a while to get to see copper but my gamepad is working like new. The poor thing is worn out so I am guessing I will have to apply conductive paint onto the grids in the next repair and maybe re-carbon the rubber membrane but I have had it since the 2000s.
@nicwilson89
4 жыл бұрын
You could also just grab an old tablet (or phone) and run something like Roccat Powergrid instead and let it retire peacefully from use to go sit and look pretty on a shelf around your machine or something
@Vermilicious
4 жыл бұрын
I think you're right about the battery leak having happened at a later stage. I dunno about lasers either, but the movement of the mechanical parts seemed a bit odd to me, like it was skipping or something, maybe not sensing it has reached the end. Might not be strictly laser diode related, I mean. I hope you find a way to fix it :o)
@donaldhenke2750
4 жыл бұрын
dam! what some steady hands.
@HomeDronen
4 жыл бұрын
Awesome video and great learning experience... Thanks for sharing!
@armstrongskyview2810
4 жыл бұрын
Great video Vince, could you do a How you film/ your camera set up. I cant work out how you get such a good first person view. Thanks
@SteS
4 жыл бұрын
He has done a question and answer video a few weeks back which shows it.
@armstrongskyview2810
4 жыл бұрын
I cant find the set up video and also searched for it, typed My mate vince set up. But nothing. Any idea what the video is called
@mushfiqaziz3414
4 жыл бұрын
@@armstrongskyview2810 the video where he shows his setup & all is titled as "500k subscriber special- My mate vince"
@SteS
4 жыл бұрын
@@mushfiqaziz3414 yep, this. Thanks for the help.
@UltimatelyEverything
3 жыл бұрын
Happy Christmas to you and your family Vince and i hope you have a good new year.
@AnonymousRepair
4 жыл бұрын
Very nice video, This bring so much memories back of fixing these cd players, It's most probably the laser , it should be much brighter than what you getting :-) would try reading the voltages with the laser plugged in.
@Mymatevince
4 жыл бұрын
Thanks Anonymous :-)
@pds8475
4 жыл бұрын
On a scope you will only see the voltage level of the laser. It basically works by shining a steady light at the CD which reflects light back to the light sensor. The amount of light reflected back varies depending on the CD. On a working CD player you could put a scope on the light sensor and see the signal. Incase you don't already know on the diagram that you showed, the laser is the one with arrows pointing away from the symbol and on the light sensor the arrows point towards the symbol.
@Mymatevince
4 жыл бұрын
Thanks PDS, I didn't know about the symbols :-)
@joawesome2319
4 жыл бұрын
Vice. Let me give you some information on discs. DVDs use a red laser, Blu-ray use a blue laser and CDs use a infrared laser. Infrared is a color that cannot be seen by the naked eye. Some cameras are able to detect this light. Your camera looks like it is not able to detect that color on screen (high quality camera perhaps). To find out if a camera could detect this color, you can point your infrared device (tv remote) into the camera to see if it is able to detect that light. The light is not seen as red but more like a white/grey light. To me, the way that the laser was shaking with the grinding noise maybe the problem to why it thinks that there’s no disc. The laser is suppose to have the ability to move across the track and not shake like that to determine if a disc is detected.
@jjzhou01
3 жыл бұрын
Would love to know if this can be fixed! I have a walkman that does that exact same thing. Lovely video!
@solveit1304
4 жыл бұрын
Ahh I was hoping that after 0.8k resistor turn, unit will read discs fine. Maybe try to measure laser current consumption on working unit, then you can compere it with bad one. Formula shows that "I = 3V / 1500 Ohm" = 2 mA. Maybe resistance value should be less like 0.3k to give him some juice, like 10mA :) Datasheet for this laser should contain maximum current value, but boy, is any way to know what laser model number is used in your Walkman? Perhaps not.
@cschis
4 жыл бұрын
Vince The laser diode is most likely open. When it is working correctly the voltage drop is .7 volts.
@hyzenthlay7151
2 жыл бұрын
As to the name, this is after the Discman line, when Sony were consolidating all their portable players of all formats under the Walkman brand (CD, cassette, MD and MP3), but prior to the funky "W" logo they made. I have a D-E201 from this time that also says CD Walkman with the old lettering that I got cheap, that wouldn't recover after skipping from a knock even with ESP turned on... Turns out the spindle was loose so it would vary the spin speed and wouldn't correct itself before giving a no disc message. A touch of ciano to put the spindle back together and now it works great!!
@masoudmontazery907
8 ай бұрын
Good luck sir 🎉
@Mazwreck
4 жыл бұрын
I see when your soldering you have the shakes bad how about putting your elbow on the table and see if that helps i do this when i am doing fine smd soldering work helps alot also try using a K tip when doing track work like this you will have a easier time soldering it
@creations7241
2 жыл бұрын
The problem isn’t the laser, it’s the track for the laser. It’s trying to move from the center of the disc to the edge. When you moved it closer to the center, you may have damaged it’s tracks. The way it reads the disc it’ll start from the center of the disc and move out wards away towards the edge as it playing music
@OmnomnomMeeries
4 жыл бұрын
Hey Vince, I think you raised the potentiometer for the laser so more voltage is gone at the potentiometer and the laser doesn't get enaugh voltage. If you lower the poti then there is more voltage to the laser. It might be a fix. Sry for my bad Englisch :)
@TheRetroFuture
4 жыл бұрын
I wanna hear more about the kitchen clock.
@Mymatevince
4 жыл бұрын
Haha ;-)
@AndrewFomin
4 жыл бұрын
"You could use your scope". I'm not saying it would have helped to fix it, but most of the time you can't test ICs using a multimeter. Input and output voltages aren't necessarily constant, they easily can be a relatively short signals which you can't see with a multimeter. And I'm not sure, but I think that more than just two pins of IC401 are related to the laser: 3-4, 50-51, 66-69, 77-80.
@Mymatevince
4 жыл бұрын
Thanks Andrew :-)
@Ihavetruth22
3 жыл бұрын
Amazing , your doing a schematic of a discman.
@GundamrussGaming
4 жыл бұрын
Great video :) I remember having a Sony Discman. Brought back fond memories.
@rocktoroll77
4 жыл бұрын
Hope you do do a revisit I enjoy your videos and revisits good thing is you tired too get it working
@scottchampion3511
4 жыл бұрын
Awesome Vince, another entertaining video to watch on my day off work 👍
@maniatore2006
4 жыл бұрын
I have the Discman from MY Childhood it is the Discman D-220 and it works 100%
@wassupjg
4 жыл бұрын
nice chillout tunes in this one
@k0fmasters
8 ай бұрын
bro one question, you know the laser resistence for playstation 1? or do you have any tutorial about that console? 1.20 laser resistence will work or its diferent in sony playstation laser?
@technixbul
4 жыл бұрын
You should turn that pot when disc is inside and it is in the process of focusing to be able to match the exact power, it is not nesessery to be a strong light. I think there is more damage to the board and some of the vias under corosion are also damaged. First spining of the disc is so laser can fall into a track, not because it focused laser on the disc. Finding a track is the fall of the light on exat spot on the photodiode matrix which then with fist spinning generates small pulses which tells the CPU to start spin the disc acording to data on the founded track.
@Mymatevince
4 жыл бұрын
Thanks technixbul, I will revisit this one and use your information and the other helpful comments :-)
@technixbul
4 жыл бұрын
@@Mymatevince Feel free to do it! In my experience the best way to callibrate laser is by ear and when its trying to focus while disc inserted (listening of the focus coils)-> just turn sloooowly the pot, listen to the scratch noise and when the noise appear -> disc is recognized and start to spin (read and play), adjust the pot until the lowest possible level of noise is acheived while disk is playing, because if you overpower it, it also won't work and may kill the laser if not - shortly. DONE you have perfect callibration without any special equipement.
@TruFon
10 ай бұрын
i don’t understand geek talk i just wanna fix mine 😢
@dom291
4 жыл бұрын
You need to look for the "ARF" (amplified RF) TP on the board, this should be listed in the schematic which makes this easier. then you hook up your scope probe to this point, on the scope you should see a nice looking eye pattern that is clear and well defined, not too fuzzy... this is hard to explain, so i'd suggest looking at videos demonstrating this on a scope, finally you want the eye pattern to be at the correct amplitude, so set the scope up to show you the peak to peak voltage and make sure it's at an adequate level - the trimpot sets this - the correct aplitude / voltage should be detailed in the schematic, remember you need a disc in and spinning to be able to do any of the above, so your gonna have to solder wires to the relevant points and extend them out while testing. , maybe the person who sold this already significantly twiddled with the trimpot.... maybe it's supposed to be only 200ohm the only way to know for sure is the steps listed above. Once again great vid Vince :)
@dom291
4 жыл бұрын
Looking at the service manual, all the required info is in "SECTION 4" page 6. In this case it' doesn't appear to be an amplified RF TP/signal (just RF)l, It shows a pic of how the waveform should look on a scope and the steps required to measure as well as providing the required peak to peak voltage of 0.35V to 0.65V - you'll likely want to set this quite high with the trimpot to 0.6v as it's weak you may even have to set this higher and out of spec if the diodes bad but you will see the eye pattern start to breakdown the higher you go. Judging by the illustration the 2k resistor in the diagram represents the potentiometer in circuit and as far as i can tell you wouldn't add an additional resistor coming off the RF TP.... but every manufacturer is different. A lot of effort for something so cheap but it would make for an interesting video and would likely help you out later down the line on other gear :) your little scope should be able to do all this, just make sure you set it to 10x on the probe and scope and set the divisions etc as per the manual.
@Mymatevince
4 жыл бұрын
Thanks for the very detailed advice Dom :-)
@strangelove1107
4 жыл бұрын
Vince, my man, please stop messing with laser potentiometers... After they are set at the factory and sealed they very rarely malfunction. They produce the lasers within a certain range in nanometers to within +/- like 5 nm. The potentiometers are then used to precisely focus the laser to an exact wavelength with no variance and glued to permanently set it. It's almost never a problem with the potentiometer. It will most often be a driver chip or a mechanical malfunction like the stepper motors or worm screw. I love the videos and your excitement to learn new things about electronics. Keep it up bud.
@PUHCsi
4 жыл бұрын
Optical drives are a world of pain, disc reading issues are difficult to pinpoint, the light emitting from the lens isn't shining from the lens it's only a reflection from the diode that has passed through a splitter and mirrored up through the lens, the motor also has to spin at correct speed and it has to vary in speed to read the info on the disc as moves from the centre out to the outer edge of the disc . The gap between the lens and disc surface is also critical ( spindle height) as is the intensity of the laser, try and find a good tutorial of how it all works together, there's a lot to go wrong when you look at it
@Mymatevince
4 жыл бұрын
Cheers Simon :-)
@cmb1972
4 жыл бұрын
Was like looking at the ending scene of terminator, the red eye going out!
@Tim_3100
4 жыл бұрын
Quite suprised that corrision had not eaten through even more of the board tracks than it had
@Snipermac99
4 жыл бұрын
Maybe use a bit more flux when tining tracks (a Lewis Rossman tip) Enjoyed the vid.
@jeremiefaucher-goulet3365
4 жыл бұрын
Needs a proper amount of flux ;)
@JasonRidenour
4 жыл бұрын
Hey Vince! Here's something fun for you to test some day: as batteries run down the amperage (current) will diminish, so if you connect your amp-meter to a battery you can watch it run down. The voltage should stay fairly consistent throughout the life cycle of the battery until you get close to the end. Think about batteries in a flashlight; the brightness stays about the same right up until the batteries are about to die, then it starts to dim. I've seen you use voltage to test batteries which is fine if you're testing if the battery is faulty, not so much if you're trying to figure out how "charged" it is. Try charging a battery all the way and test the current, then run it down a while and test the current again. Also, as batteries age they hold less and less current, so look at an old battery vs a new battery: charge them fully and look at the amperage on each. Have fun!!!
@Zippee2020
4 жыл бұрын
I’m torn, I wanted you to repair it but massively relieved we didn’t get to listen to Jedward 😂
@oscamosca_5804
4 жыл бұрын
Instant click once I see Vince on my Sub box 😤
@allrock1238
4 жыл бұрын
All CD's are read from the center out,, some CD players will use the laser to detect "Disk present" first, but then command the tracking servo to seek the inner location they usually do this by running the optical sled towards the disk spindle until it strikes a micro switch that tells the player , You have reached the inner track, it will then try and read the disks table of contents ,, you should see the worm gear drive attempt to move the optical pickup sled to seek this position, if the laser is too weak , it might not seek as it may think "no disk present why seek ,, most CD players seek inner track detect as a part of there attempt to read anyway. be mindful A CD players laser light emissions are in the infrared spectrum also be aware laser diodes are extremely static sensitive and easy to damage, some people will not unplug the ribbon cable unless they place a bridge the static protection pads with a solder bridge first,, and new ones usually ship with a solder blob in place that protects them. they wont work until this is removed ..watch videos on CD player repair to better understand how they read the disk ,, also make sure the lens is clean ..
@game_master_rukia
4 жыл бұрын
The laser is trying to move past the center but keeps hitting the motor
@alexandrabakker3944
3 жыл бұрын
Hmm it has a protection switch right next to the laser to protect it when moving when not using it. If you let it on and try to play it no wonder it doesn't work
@bobjerome5390
4 жыл бұрын
hi at last you know about all the feedbacks i used to get them on my old channel all the time cassette deck reel to reel i used to do i was crazy high numbers why i stopped doing video
@jrsc01.
4 жыл бұрын
What was the switch on the inside of the case for, G-protection? What happened to it later in the video?
@retractingblinds
4 жыл бұрын
Don't forget you can use the corrosion vomit to identify problematic areas, it's not always the best idea to clean it all off immediately.
@junglejonny1000
4 жыл бұрын
Why would you not just run an insulated wire from termination to termination instead of trying to solder that fine wire in the middle of the trace? Especially when it could short out to another wire, trace or component since it isn't insulated.
@Mymatevince
4 жыл бұрын
Those wires are insulated but they don't look like they are. They are the same kind of wire that are used on transformers and motor windings. I think it can be called magnet wire or enamelled wire :-)
@junglejonny1000
4 жыл бұрын
@@Mymatevince Thanks for the explanation. Love the channel and all your amazing content. And thanks for the simple reminder that we can do things like that too if we just try.
@Scott-M1
4 жыл бұрын
I had this happen on a PS1 lid switch. Had to buy a donor console. Couldn't find the part anywhere!
@AnotherDud3
4 жыл бұрын
Didn't notice but did you actually try cleaning the laser too? ISO + cotton bud
@schweatty
4 жыл бұрын
Yes. He did that
@kotm3
4 жыл бұрын
I love you and your videos Vince. But please stop saying tracks and say traces instead. Keep up the great work. Lasers are always a pain in the bum!
@Mymatevince
4 жыл бұрын
Haha, thanks. I think in the UK they are called tracks and in other countries traces :-)
@lochanathambeliyagoda5065
4 жыл бұрын
Hey my mate vince u wanna try fixing my macbook i dont really care if it breakes cause i am going to upgrade if it does break but if you can fix it that wud be cool
@CLC-1000
4 жыл бұрын
Great video Vince. Shame you could not fix it.
@jochenwuerfel
4 жыл бұрын
I guess the dropped the "Walkman" due to its introduction back then as a cassette player, so customers don't mix up stuff or even think it might somehow still plays tapes.
@MickeyFKNMouse
4 жыл бұрын
Discman was the original name for Sony’s portable CD player. If I remember rightly they changed the name to their Walkman brand around 2000. But no difference in what they are. Discman is just an early brand.
@Mymatevince
4 жыл бұрын
Thanks Mickey :-)
@meatwad74
4 жыл бұрын
I got my first cd player, the sony diskman in 1992. came with aiwa headphone. sounded fantastic. for a good 6-7 years after that it was my primary cd player which I attached to amplifiers, car cassette players
@mikethedigitaldoctorjarvis
4 жыл бұрын
I remember doing that !...jack to jack plug into the car stereo auxiliary .
@meatwad74
4 жыл бұрын
haha no I plugged it with one of those inputs shaped like a cassette tape
@jasinere35
4 жыл бұрын
power fault & the laser unit should return to the centre as soon as you turn it on
@VirtualSpeed
4 жыл бұрын
the laser clicking like that against the spindle motor is not normal. It seems that the switch that says where is the end is faulty.
@VirtualSpeed
4 жыл бұрын
still, if the laser is getting the right voltage it should light up more than that.
@matrixgamesrodrigo
4 жыл бұрын
soak the optical drive in water with a little detergent. Then rinse with pure water and let dry well
@quantumleap359
4 жыл бұрын
Good troubleshooting, but there are multiple problems with this poor thing. The laser output is def way too low. Also, if the laser sled does not scan over toward the spindle upon startup, then there is a problem with the start routine, or a mechanical bind that prevents the sled from moving. A leaf switch tells the processor when the sled is at its innermost position, and the processor is not seeing that switch closure. Good luck, but it may be time to bin it.
@KorAllRBare
4 жыл бұрын
😓 Looking forward to the re visit, my money is on the laser is shot, mind you only if all the capacitors check out OK, oh and that chip associated with incorrect voltages..
@BikerBloke600
4 жыл бұрын
Hi Vince thought you were on holiday again lol Mick 👍🍻
@aqouto8845
4 жыл бұрын
My uncle has one and this will work perfect for him thanks 👍
@nicwilson89
4 жыл бұрын
The heat of the iron/solder is probably more than enough to burn off the coating on that wire, depending upon what it is. Just might save you a little effort
@stllama
4 жыл бұрын
did it work?????
@speedwaynutt
4 жыл бұрын
Yayyyyyy another cd walkman video
@Ruslan.88266
4 жыл бұрын
Where did you get that blue mat from?
@Charlie6969
4 жыл бұрын
Look up: "Silicone solder mat" on ebay
@cesargtz7691
4 жыл бұрын
You know that you can use an phone camera to see the IR light, phone cameras can see IR light, it sees it as a purple glow, you can even see it on a tv remote
@johnbreedlove21
4 жыл бұрын
will the laser shouldn't click that much when you track when it tries to read the disc it shouldn't bounce back and forth it should just move forward slightly move up and down freely it shouldn't click back and forth
Man I kinda want to get a disc man but they weren’t ever that portable, aside from the fact they don’t fit in your pocket
@pinklightninggacha
4 жыл бұрын
the lasers shot mate
@andrelacombe2822
4 жыл бұрын
Diskman sounded cooler than walkman back in the day when CD's were new and analog tape was already second-best compared to LPs, IE disks were 2 levels better than cassettes. Sounded cooler but the early diskmans were very unreliable compared to a tape player
@leedawson382
4 жыл бұрын
He’s back :-)
@user-se8nh3yu1e
4 жыл бұрын
Lee Dawson with a black disc man.
@jjohnson71958
4 жыл бұрын
The ribbon cable is for the LCD display
@069101692
4 жыл бұрын
Vince change the laser head to a new one, this one is no longer working.
@themetalmicky
3 жыл бұрын
do a video on trying to fix jedwards hair cuts
@lucylucy3630
4 жыл бұрын
Try to power up the motor that spins the disk with 3v from another power supply and see if the player reads something...
@PrawnCocktailBro
4 жыл бұрын
Day 324 of hoping Vince will setup a Patreon account
@jrsc01.
4 жыл бұрын
A CD Walkman with good taste lol.
@rosariodagosto6484
2 жыл бұрын
this unit is water damaged vince
@stllama
4 жыл бұрын
trying to fix: faulty sony discman d-ej715
@michaelturner4457
4 жыл бұрын
Planet Jedward is one of my favourites.
@jeremyowen1
4 жыл бұрын
I had that exact walkman when I was 9 or 10. It skipped when you walked with it. Sort of ironic.
@jeremiefaucher-goulet3365
4 жыл бұрын
That's because you are supposed to jog with it, not walk if you want the anti-skip feature to work :D It says "jog proof" on it.
@jeremyowen1
4 жыл бұрын
@@jeremiefaucher-goulet3365 Is that what customer service would of told me if I called and complained? "Our patented walkman is not meant for walking. Try running at a brisk pace to enable the anti-skip functionality." Good ol' Sony.
@jeremiefaucher-goulet3365
4 жыл бұрын
@@jeremyowen1 Still better than Apple. From them you would have gotten a "You're holding it wrong" 😂
@jeremyowen1
4 жыл бұрын
@@jeremiefaucher-goulet3365 lmaoo!
@bobjerome5390
4 жыл бұрын
hi again it can be 1000 a day people leave you have 500k subs wait till 1000 subs i was getting the video on hot up cassette decks went crazy after that i did no more the video are on the cold side there are video that are hot just wait till you find some thing that doe;s very well
@VOLTRONDEFENDER4440
4 жыл бұрын
1:15 lol
@d2d2505
Жыл бұрын
discman was first
@borgred
4 жыл бұрын
why have you got a jed disc lol
@DEmma1972
4 жыл бұрын
Nice try. Usual Vince. Break something that doesnt need fixing and make life harder lol
Пікірлер: 161