Great vid, much more about identifying, cleaning and restoring than tuning. Certainly kept me interested.
@4Truth4All
12 күн бұрын
Nice job Dave!
@RoBBz2000
4 ай бұрын
a pleasure to watch.. :) glad to have found your channel!
@DaveCorinth
4 ай бұрын
Awesome, thank you!
@Rigus208
3 ай бұрын
Dave Ty for this vid. Learned a lot to enhance the twinkling of my 60. 1\2 I found when I was the same age 😉13 yrs later it’s still my favorite.👍😇🇺🇸
@DaveCorinth
3 ай бұрын
I love the 60 1/2’s, they are great little planes to have around the shop. Especially when they are tuned. I hope this video was a helpful tool in getting yours tuned.
@ga5743
4 ай бұрын
Nice job thanks for sharing your skill.
@martinhawrylkiewicz2025
4 ай бұрын
Wow really nice work!
@darinhalvorsen
4 ай бұрын
Great work on the plane and extremely well done video.
@DaveCorinth
4 ай бұрын
Glad you enjoyed it
@bentontool
4 ай бұрын
That's the way to do it!
@manny.u1958
4 ай бұрын
Hello from Tijuana; I brought one in a flee market for $5 dollars I don't know if it is old it has ( PAT' D.10-12-97) I have been cleaning it and fallow your instructions, to tone it, thank you for sharing your experiences cheers from Tijuana
@DaveCorinth
4 ай бұрын
The patent is referring to Andrew Turnbull’s lever cap. That plane certainly is old as the patent was issued on Oct 12 1897. Great find. And good luck with the tune up.
@Heeman5
2 ай бұрын
Awesome!
@robertmceuen3630
Ай бұрын
I have a Stanley 60 1/2, but it has no finger cut outs in the sides. I read something about it being a pre war model. Put a Veritas blade in it; darn good little plane.
@DaveCorinth
Ай бұрын
Yours is a War Era, made during WW2. They are really good planes and usually have slightly thicker castings than the earlier or later ones. That Veritas blade is definitely an upgrade versus the original Stanley.
@robertmceuen3630
Ай бұрын
@@DaveCorinth Thanks for your reply and clarification. Much appric iui ated
@1pcfred
4 ай бұрын
I was just looking at my planes and they're looking like how that one started out. I thought I had a 60½ I have a plane that looks like it but it is not marked such.
@kentgreenough75
4 ай бұрын
I bought a new Stanley 60 1/2 and what a mistake. The sole was convexed! It took hours to lap flat, but I was determined to make it work. Next the bed behind the mouth was uneven, so I flatten that. Then flatten the blade, again it needed a lot of sanding, and the sharpened the blade. Now the real fun began. As the blade came out it was crooked! One side higher, tilting the entire blade! No amount of adjustment made a difference. I tried a shim on the low side and no improvement. I’m defeated by this plane and now it sits on the shelf to remind me to never, ever buy a new Stanley plane. My old Stanley’s are great, I have five of them, all a joy to use. Any thoughts, did I miss something? Good video.
@martinhawrylkiewicz2025
3 ай бұрын
Great restoraton! Just curious if you coukd use WD40 for cleaning the grime and dirt off too?
@DaveCorinth
3 ай бұрын
Sure, WD 40 works fine, I like the CMT cleaner because it removes paint splatter, and any wood resin that might have built up on the plane, especially near the mouth.
@chris-C8
Ай бұрын
Hey Dave, I love your videos. I recently refurbished a Stanley No. 5 Type 18. However, I noticed that over time, the body starts to get little spots of discolouration (it looks similar to the metal table at the end of this video when you were using Scotch Bright). I put some 3 in one oil to protect it, but it didn't do much. Is there something I can use besides Johnson's paste wax to keep it looking sharp?
@DaveCorinth
Ай бұрын
Union Mfg sells an Elixer that keeps rust off. Check out their website. Unionmfgco.com Myself I don’t mind a little discoloration after I’ve been using one. When I’ve used one a lot, I’ll hit it with some scotch brite. It’s unprotected metal so it’s going to oxidize.
@chris-C8
Ай бұрын
@@DaveCorinth Thank you for the reply! That makes sense. I'm new to woodworking and hand planes, so seeing all these beautiful planes on KZitem, I thought I was doing something wrong because the plane gets superficial staining in certain spots. I will check out the product you suggested. Thanks again!
@Malba1776
Ай бұрын
Wow u scored that block plane shined up like new, how much did u buy it for? THANX for the video !!!
@DaveCorinth
Ай бұрын
Not much I think around $20.
@aldolajak1267
3 ай бұрын
Not sure how many block plane users there are out there, but I applaud you dedication. Technology is obviously giving way to the old tried and true methods of woodworking. Sad that high planing and high speed routing are replacing tried and true traditional methods.
@DaveCorinth
3 ай бұрын
In the last 20 years traditional woodworking has made a roaring comeback. Good quality hand tools are in high demand and I hope that this video helps in setting up one of those tools for optimal use.
@dannyhale7645
3 ай бұрын
Where did you find your very fine wire wheel?
@DaveCorinth
3 ай бұрын
I bought a box of wire wheels at an auction a few years ago and there 4 in there that were the finest I have ever seen. I’ll find out who makes them and get that information on here.
@dannyhale7645
3 ай бұрын
@@DaveCorinth , I would appreciate that. Have you ever tried the nylon bristle ones? I've heard they're easier on the metal.
@DaveCorinth
3 ай бұрын
The wire wheel I use is an Osborne 604k, they are made for aluminum, brass and bronze. The bristles are stainless steel and very fine.
@dannyhale7645
3 ай бұрын
@@DaveCorinth , thanks!
@martinhawrylkiewicz2025
3 ай бұрын
Would you sell it?
@DaveCorinth
3 ай бұрын
Already sold it. Usually I list them on eBay shortly after they have been tuned, restored.
@martinhawrylkiewicz2025
3 ай бұрын
@@DaveCorinth can you please tell me your eBay handle so I can check what you have for sale?
Пікірлер: 36