Really useful especially in our place where ready to use nozzles are rarer than gold. Thank you!
@adamfranco173
Ай бұрын
This is absolutely fantastic!! I met guy up in Maine working the river with your prototype. It worked flawlessly!!!! I will be building one tomorrow. Thanks for the insight🤘⚒️
@davidwright8199
4 ай бұрын
This is the BEST EXPLANATION of a dredge I have seen on utube. You are a star. Are you using a 12v pump or gasoline?
@randallmonville2310
4 ай бұрын
5.5 hp gasoline.
@davidwright8199
4 ай бұрын
@@randallmonville2310 thanks very much indeed. 😁
@genofromrenoprospector6940
2 жыл бұрын
I'm not sure this is very cost effective considering time and material when you can buy a steel nozzle for $100. But this is an excellent video for the diy guys.
@mrgreenswelding2853
3 жыл бұрын
Great idea, but bondo absorbs water. Use a fibreglass reinforced filler instead
@MrMolina52
4 жыл бұрын
muy Bueno......gracias!!!!!!!!!!!!!!!!!!!!!
@jimfamille7025
5 жыл бұрын
and for agent de démoulage take soap for a kitchen.... palmolivei have a friend we know do thatttt is a nice twisttt try thist jim....
@randallmonville2310
6 жыл бұрын
The "u" piece is to get the high pressure water to the jet.
@Sinasongway
6 жыл бұрын
Nice work. But how many hp is of your motor pump? Can I do dredging of a pond with 2 hp motor and this nozzle? If not what should be the min capacity?
@joelrojes5239
Жыл бұрын
Parabéns ! Gostei muito . Tenho uma saída da motobomba de pressão a gasolina de 2" polegadas ,,,, esta pasta que você coloca é uma cola ? E onde posso encontrar para comprar ? Obrigado desde já . Parabéns pelo talento e a forma clara de explicar .Att.
@randallmonville2310
Жыл бұрын
Bondo is an autobody filler. Its used to repair dents on car bodies. You should be able to buy it at any auto parts store.
@joelrojes5239
Жыл бұрын
@@randallmonville2310 Entendido. Meus cumprimentos ! Obrigado me ajudou muito. Sucesso para você , em tudo que faz , fez e irá fazer. Att. Joel Rojes. direto de Brasil.
@joelrojes5239
Күн бұрын
Muito bom. Parabéns!
@lancetrantham1230
3 жыл бұрын
I am dredging a hole in my boat slip and saw your video and said this may work. My question I am curious about is that if I use a 4 or 5 foot gravel (in my case sand)suction pipe would that affect the performance? I need to move about 3 yards of sand for my keel to rest in. Thanks for share your video.
@randallmonville2310
3 жыл бұрын
It will. But it may take a bit of time. You can extend the end of the nozzle. Try it.
@KevenDRayne
6 ай бұрын
I'm in (or under) the same boat. Did you have success?
@erikreinertsen1647
5 жыл бұрын
That has alot of suction. You really seem to know what your doing. I am currently attempting to build a 4 inch nozzle in order to suck sand off a lake bed and pump it behind a new seawall for backfill. I am attempting to pump the sand up to 6' in height. So far I have been able to pump sand but not enough. I dont have good suction. I am running a riverside 2-1\2" high pressure pump powered by an 11hp honda engine. What should my jet size be for my 4 inch system? Do you have any suggestions?
@MJ69090
4 жыл бұрын
I need to do the same thing and my design incorporates a second pump further up the discharge line, which will act as a booster.
@sirwilliamofpennylot
6 жыл бұрын
Enjoyed the vid, does the "u" piece serve any purpose?
@StevenSchoolAlchemy
6 жыл бұрын
Great idea!
@sergiomamontoff2265
3 жыл бұрын
Хорошо придумано. Спасибо
@RedmanOutdoors366
6 жыл бұрын
Nice build I couldn't do it better myself :)
@randallmonville2310
6 жыл бұрын
REDMAN PROSPECTING thank you.
@RedmanOutdoors366
6 жыл бұрын
Randall Monville yup happy prospecting
@christiaanschlechter3797
6 жыл бұрын
+Randall Monville hi I'm also macing a dredge nozel but want to cnow what size nozel works best to create the vacume .any advice pleas
@randallmonville2310
6 жыл бұрын
Christiaan Schlechter start with .5 inch. Will depend on pump pressure and hose length and diameter of dredge. You can drill it out to make it bigger.
@robmcguire963
6 жыл бұрын
Nice idea Thanks for sharing, sO the size of the inner hole is 1/2 inch correct?
@christiaanschlechter3797
6 жыл бұрын
any digestions on nozel size need help pleas
@bertramlrezenet9311
Жыл бұрын
Where's the venturi? 🤔
@randallmonville2310
Жыл бұрын
Its the part made with the bondo.
@djpitr
6 жыл бұрын
well its nice use of my principle :) that i use in my nozzle i made :)
@lousimoneau7564
5 жыл бұрын
,hi Randal,,will a 50 cc honda work,,my keen nozzle scree up,nice work
@randallmonville2310
5 жыл бұрын
50 cc is small. I don't think it will work. Try it though. It may be ok.
@rustycreed4638
5 жыл бұрын
Would I need to make some diameter adjustments if I wanted to use a 3000gph 12v bilge pump?
@randallmonville2310
5 жыл бұрын
I doubt it would make enough pressure to create a good suction. All you can do is try though. Start at .5 dia and increase .125 till you get suction.
@jimfamille7025
5 жыл бұрын
the best friend at the putty are a thinner with clothes ....hihihihhi not yours finger ...hhiihihihi
@jimfamille7025
5 жыл бұрын
for a ultimate aderance with a pvc pipe wash interior pipe witch thinner and after sand 180 ans re wash take a carton for mix and stay in your box tool for a next time is more gravely ...sanding... more batch more sanding he falling love in a body shop i work ... sorry for my english im stay in quebec city.......and for your bubble take a old electric sanding put your piece witchputty wen on in a pad the vibration make a job see a next tine ....jim ...famille jim594 at g mail
@edmelville9292
11 ай бұрын
This is so wrong the pressure water has to be introduced immediately after the suction side of nozzle or pressure water will be pushed out of the suction side. I am a mechanical engineer and your design goes against physics sorry😢
@randallmonville2310
11 ай бұрын
The pressure water goes over the suction nozzle creating the suction. If you extend the pressure nozzle past the suction inlet it will jam with rocks. You can see it working at the beginning of the video.
Пікірлер: 41