Hi mister! I hope you are well! Subtitles are not available for this video, can you enable this feature? If so, then thank you very much!
@gavinclayton9552
4 жыл бұрын
Nice Dan!
@davidsomething4867
2 жыл бұрын
Hi Daniel, I was dreaming about a solution to this issue as only have a ER11 collet holder a few nights ago as I've jus ordered a AXBB-E with UCCNC 🙂 I've registered on the forum but which macro did you use. Sorry if you have already answered this question P.S I don't want to join Facebook jus for this.
@medleymedley4971
3 жыл бұрын
Please seating axe x,y, z end probe for normali use . Bogdan
@lauriemattila5936
3 жыл бұрын
Thanks for video ….any chance on how to install Macro and edit for machine. Just received my Anxion and the learning curve is very steep. Cheers
@tomahawkcnc5583
3 жыл бұрын
The altered M6 macro is placed in the profile folder to overwritethe existing one . When a M6 is called in gcode it executes the M6 macro
@cnchobby2130
2 жыл бұрын
Thanks for the video! I tried the same procedure, but to zero my z reference plane, I use a 5mm gage, but even if I put that value in the gauge height, when I reference the workpiece, the zero is 5mm above the reference plane... any advice?
@tomahawkcnc5583
2 жыл бұрын
You need to click the use guage button
@cnchobby2130
2 жыл бұрын
@@tomahawkcnc5583 if you mean the "Axis 1 count gage" button, it was already enabled...
@cnchobby2130
2 жыл бұрын
@@tomahawkcnc5583 what version of UCCNC where you using? I have the 1.2114 and my doubt now is that the bug was introduced with this version...
@tomahawkcnc5583
2 жыл бұрын
@@cnchobby2130 i am on 1.2115
@cnchobby2130
2 жыл бұрын
@@tomahawkcnc5583 Thanks, I will try with that version
@HenryOCarmichaelSmith
2 жыл бұрын
RIP headphone users
@nistax2880
3 жыл бұрын
what macro are you using ? could you share a link ? please man I'm desperate
@tomahawkcnc5583
3 жыл бұрын
It's on the uccnc forum and uccnc Facebook group page
@nistax2880
3 жыл бұрын
@@tomahawkcnc5583 i can't find it anywhere and I don't even know what specific macro to look for since there are many , could you please share a link , the macro you are using does exactly what I need. I will ofcorse modify it for my specific machine. Thanks in advance , please I'm really desperate
Please help me with m6 macro for semi-automatic tool change. Thanks!!!
@tomahawkcnc5583
3 жыл бұрын
M6 macros can be found on the uccnc forum or the uccnc users facebook page
@zichoreduard2729
3 жыл бұрын
I tried 3-4 macros from the forum and I managed to break a bit. I wrote to you that I did not find a correct one. Thanks
@tomahawkcnc5583
3 жыл бұрын
@@zichoreduard2729 any macro will need to be edited to suit your machine . And watch the video on how to reference the tool to its offset .
@bogas78
3 жыл бұрын
@@tomahawkcnc5583 is this that post --> facebook.com/groups/484346762309609/permalink/848403539237261 ?
@xtrapro
Жыл бұрын
@@tomahawkcnc5583 Is it really that hard to post a download link from the forum? You were explicitly asked for a link. There are people who don't want to use Facebook out of conviction. Instead of just posting a direct download link, referenced 3 times on the forum and Facebook. Interesting attitude
Пікірлер: 23