really good video, used it to mod my oled with no issues! Thanks amigo
@Wayayeo
4 ай бұрын
This is what I like to hear. I’m very glad it helped. 👍
@junjloc3774
4 ай бұрын
I hope you charge well you have some real skill and make it look super easy
@donaldbarstow3545
12 сағат бұрын
The smallest wire I have is 20 gauge. Will that be small enough?
@jackipiegg
4 ай бұрын
12:48 Do cover the inner side of the nand shield with kapton tape. The solder blob will touch the shield (grounding it) at some point in time if the console is dropped or shaken. Happened to me once.
@Wayayeo
4 ай бұрын
Good point. Thank you.
@quajay187
4 ай бұрын
I find that the dark blue Dat 0 connector is more stable than the yellow one
@jmp91
4 ай бұрын
yesss
@OkiDingo
3 ай бұрын
Was that my Splatoon OLED? I’m curious why you don’t put the heat shield back on after install? Is it just not necessary?
@Dan-v3i
3 ай бұрын
I hate to be that person, but what are you installing on the board? I’m pretty sure it’s some kind of bypass or a common issue on these Oled’s, but I haven’t worked on any thus far, but would love to know what issues this resolves with them Thank you
@hannoverfisst2414
Ай бұрын
@10:55 you dropped some solder on the bottom of that 3.3v connection at the top of the ribbon cable real quick but you didn't say anything and when I pause it, it looks like there are connections at the top and bottom but you just did a real quick job on the bottom connection but not the top? @ 12:05 you show a really good pic of it but the top is not soldered? Does that 3.3v not need to be connected at both ends? It also looks like you're supposed to jump the two together on the top and bottom? What's going on there? Seems kinda important.
@Wayayeo
Ай бұрын
Bottom of cable is the 3.3 v top is ground but chip is already grounded so not needed. Just saving time.
@x1ic1x
4 ай бұрын
10:26 for some reason solder never wants to grab the flex cable with this resistor, does it even need to be soldered together to work?
@Wayayeo
4 ай бұрын
No need to solder it. It will work just fine as this is just for support.
@error346
Ай бұрын
Can you explain the software part to finish the work? Thank you!
@underscore814
3 ай бұрын
At 5:04 i recommend once slid in to check with the multimeter to ensure you are getting the correct readings before grounding it to the shield.
@Wayayeo
3 ай бұрын
I’ve done it so many times that I developed a good hand but your advice is definitely good. Thank you for the input.
@rogergillette8426
2 ай бұрын
So I attempted this myself, though I did ok, had all the right readings. Got the firmware flashed and it won't boot. It gives me one solid blue light, then yellow x2 a pause yellow x2, pause yellow x2 and then nothing. What could I have possible messed up? 🤦♂️
@Wayayeo
2 ай бұрын
Possibly your DA0 point but I’d check for any shorted points. Good luck
@rogergillette8426
2 ай бұрын
@Wayayeo yeah, I'm not sure... I think I messed something else up, I removed it and the system still wouldn't power on, so I think it's a new mobo time and pay someone with better eyesight to install it 🤷🏻♂️😬😅
@Wayayeo
20 күн бұрын
Check for shorts.
@qaishusam
4 ай бұрын
Thanks for your video! Do you mind sharing the model of your microscope? Footage looks sharp and detailed. Good job 🎉
@Wayayeo
4 ай бұрын
You’re welcome. Microscope is a Leica. Camera is an Eakins. I have tried a few others and pretty much any $300 and up look the same. Got it on aliexpress, no model #.
@enerqiezz2163
2 ай бұрын
Which Temperatur is recommended?
@Wayayeo
2 ай бұрын
680F
@tonycheck
Ай бұрын
Hi, thank you for this tutorial! Where i can find that dat0
@mincraftgimer
23 күн бұрын
What temperature was your soldering iron at?
@Wayayeo
23 күн бұрын
680 F
@mincraftgimer
23 күн бұрын
@@Wayayeo Thanks!
@evenemad5010
2 ай бұрын
Which microscope did you recommended me to get one? Thanks in advance.
@Wayayeo
2 ай бұрын
Anything from a $400 rage from aliexpress works fine
@evenemad5010
Ай бұрын
@Wayayeo thanks for replying! Which wier soldering do you recommend my to use? I'm using this one ( Tin 97%, Silver 0.3%, Cuper 0.7%, Flex 2%), but I'm having a hard time to deal with it. My machine is Sugon A9. Big thanks in advance.
@triderg7-816
4 ай бұрын
Thank u for this step by step tutorial. How can I recognise latest rp2040 mod?
@Wayayeo
4 ай бұрын
You’re welcome. Get from a reputable seller. You can always upgrade firmware. Good luck !
@nixskups4788
3 ай бұрын
Hi, what is the temp. that you use for soldering?
@Wayayeo
3 ай бұрын
It really depends on your equipment but I find 680-720 f works for me.
@nixskups4788
3 ай бұрын
@@WayayeoI have an smd soldering station hot air + stylo can reach 900 F. I ask this because I planned to mod my Switch v2 and dont want to overheat the pcb.
@S3SIC831
4 ай бұрын
Thanks
@Wayayeo
4 ай бұрын
You’re Welcome
@LonzoTube
4 ай бұрын
Which cables are you using? 36awg? At what temperature are you soldering it to make it strip so fast? Thank you
@Wayayeo
4 ай бұрын
38 awg. 700F on soldering tip.
@LonzoTube
4 ай бұрын
Thank you, I'm doing some practice and when it comes to wires, it's a mess for me
@joesaiditstrue
4 ай бұрын
Your videos are showing up in fyp feed to ppl who aren't subscribed. What's RP2040? should put more detail in the title
@Wayayeo
4 ай бұрын
I appreciate the info.
@KngKurd
4 ай бұрын
Raspberry pi 2040 is a chip that is universally used for lots of mods including picoboot on GameCube
@jeblimohamed6983
4 ай бұрын
Hello, thank you very much for everything you do I have a problem the device boots directly to the base system and does not enter the modified system The shape of the flashes of the LED lamp is as follows : kzitem.infoO8dwRjmyKEs?si=zaDRE-_ccsvqzlR_ Can you help me solve this problem? Thank you very much
@Wayayeo
4 ай бұрын
Check all points with multimeter. Also check for shorts.
@jeblimohamed6983
4 ай бұрын
@@Wayayeo ok thank you i will check
@GameOn-li6qe
4 ай бұрын
I have this exact problem where it flashes blue followed by 2 yellows 3 times I checked all the connections are made perfectly no shortage either All the values appears to be ok on continuity any advise???
@jeblimohamed6983
4 ай бұрын
@@GameOn-li6qe In my case I think the problem is in point C As far as I know, the value should be between 0.6 and 0.7 For me, the color of the flash is blue and green maybe your problem is modchip firmware, i wish you find a solution
Пікірлер: 53