Thanks SHURE after watching this video I'm a bona-fide A1
@dinnorparty
10 жыл бұрын
What do you do if you press mode and scan is not displayed?
@en4cer450
6 жыл бұрын
I recently obtained a Shure ULXP4 receiver with a Shure ULX1-J1 wireless bodypack and a Shure ULX2-J1 SM58 microphone. With all three units powered on and set to the same channel and the same group, I am not receiving any of the lights on the RF or TX Audio indicators on the front of the receiver when sound is delivered into the microphone. The Output on the back of the receiver is set to "Mic" and both A and B antennas are attached. Can you please tell me if I am missing anything? Does there perhaps need to be anything plugged into the AUX High Z or the Balanced Low Z port on the back of the receiver to get the lights on the RF and TX Audio indicators? I appreciate any feedback or help.
@shure
6 жыл бұрын
Check your email for a response from our support team!
@en4cer450
6 жыл бұрын
Thank you - I haven't received an email response yet but I will wait for it.
@arcturusraze1236
6 ай бұрын
Recently got my hands on a ULXS4 and a ULX1-G3, but they don't seem to register one another when set to the same groups/channels. the MHz ranges are 554-590 on the receiver and 470-506 on the transmitter. Is this a problem? To the best of my knowledge, they were used alongside each other for a few years, but I may be wrong. Thanks!
@shure
6 ай бұрын
They need to be set to the same frequency range or within a compatible range. In this case, the frequency ranges of the two devices do not overlap, which is likely why they are not registering with each other.
@jayantharaj6121
4 жыл бұрын
I wanted to know how to set the TV setting but you did not explain it in this video.
@shure
4 жыл бұрын
Our support team can help out! You can open up a ticket with them at www.shure.com/americas/contact.
@arykedawg1
10 жыл бұрын
how do I connect it to a pedalboard?
@MichaelD8393
9 жыл бұрын
Just plug a guitar cable from your pedalboard into the quarter inch output on the receiver.
@MichaelD8393
5 жыл бұрын
@Lachlan Revolver Run a cable from the output of the receiver to the input of the first pedal on the board.
@MichaelD8393
5 жыл бұрын
@Lachlan Revolver Yup, after you connect the receiver, the signal; is carried through the pedals and to the amp from the output of the last pedal. Or if your amp has an effects loop, just plug the receiver into the amp and run the pedalboard through the loop.
@clmedia6971
2 жыл бұрын
Hello there! can i use L3E freq 638-698 Mhz transmitter with L4E freq 638-698 Mhz receiver?
@shure
2 жыл бұрын
Thanks for reaching out! Our Support Team will be able to help troubleshoot this with you. You can reach out to them at shu.re/contact.
@AlviroMarquez-ph2ch
Жыл бұрын
I have a problem with my ULXS and ULXP model receivers. They are both consistently have dropout signals every 5 seconds. What should be the problem?
@shure
Жыл бұрын
We're sorry to hear this, Alviro. Our Support Team can help you out. You can reach them at shu.re/contact.
@user-VIntuitive
9 ай бұрын
Antenna
@mikeymikey7917
3 жыл бұрын
SHURE
@AhmedKhan-qh1cz
2 жыл бұрын
Need the price
@shure
2 жыл бұрын
Hello! You can learn more about our wireless systems here: www.shure.com/en-US/products/wireless-systems.
Пікірлер: 23