Diagram I ordered this tachometer and got the color diagram for it, I am posting it here, hope u find it helpful Black,purple - rpm Black- live from key ignition Light blue- right side signal Dark blue-high light White yellow- neutral Orange- left side signal Brown- running light Red- direct from bat Black white-speed Purple- connect to sensor directly Light green- gear 1 Light green brown - gear 2 Light green green - gear 3 Light green yellow - gear 4 Light green black - gear 5 Light green blue - gear 6 Green black - grounding Green black - grounding Blue white - fuel level Found your video much helpful . Thanks for posting this !!
@nick39691
7 жыл бұрын
there is 2 of them that are the same but they used different color for the wire i got the one with the wrong color but i look at pic and was amble to fine what color did what by the placement for the one i have the rpm color is blue and weight and my fuel level is yellow and black
@Mental-Maniac
6 жыл бұрын
can you send me the whole diagram please.
@Khumbu65
6 жыл бұрын
Hi! can I install this in Royal Enfield ? Where can i buy this...?
@thefid23
6 жыл бұрын
Barry Ziza thanks so much for that. Tried connecting red to battery and it goes off. Got a black/white which I think is the ground on my bike. Does that go to the green/black on the plug? Been a total nightmare lol
@storman7609
4 жыл бұрын
Show my videos : kzitem.info/news/bejne/u6uXyKN-hnibiqw
@gdavid71
8 жыл бұрын
Thanks again for the help. I thought I would share my experience installing on my 1984 Honda Magna V65. For the tach, I followed your advice and wired into the blue wire of the pulse generator, but I programmed the speedometer for 2 cylinders instead of my 4. My MPH reading is more accurate by just programming a higher number for the circumference /number of magnets. I'm using 818 and it's much more accurate. Thanks again
@storman7609
4 жыл бұрын
Show my videos : kzitem.info/news/bejne/u6uXyKN-hnibiqw
@MitchellJnBaptiste
8 жыл бұрын
Thanks man, it worked! A bit bouncy but it worked. Have not ridden the bike yet but at neutral it responds.
@storman7609
4 жыл бұрын
Show my videos : kzitem.info/news/bejne/u6uXyKN-hnibiqw
@gdavid71
8 жыл бұрын
Thanks again for the video. Here's my experience with my 1984 Honda Magna V65.... My MPH setting is more accurate by playing with the numbers, rather than following the instructions. I programmed in 818, much better than diameter / the 3 magnets that I'm using. Also, I set it for 2 cylinders instead of my 4, and followed your advice and wired into the blue wire of the pulse generator. Thanks again
@CatDaddyTuning
7 жыл бұрын
blue wire on my cdi on my yamaha worked too
@OldCrewPH
7 жыл бұрын
I have also Honda 125, it's also blue wire and 2cyl instead of one.
@tacobumpers9493
6 жыл бұрын
where did you get the 818 from if you don't mind?
@MrEC9
6 жыл бұрын
FUEL GAUGE Some of the posts on this and other videos state that grounding the fuel gauge wire (blue and white) will cause the fuel gauge to stop flashing. With my ones (3 of them) this was not the case. I have found that you need to ground it via a resistance of between 30 to 500 ohm. Anything more or less wont have any effect. 500ohm displays 1 bar (of 8) i.e. almost empty. 30ohm displays 8 bars (full). (about 330ohm is half full etc.) So if grounding the fuel wire doesn't work for you, try grounding it through a resistor between 30 and 500 ohms.
@robinper731
8 жыл бұрын
how did you mount the speedo i have same one and having trouble thinking of a way to mount it
@williamsnelson
7 жыл бұрын
I have the same one but can't get it to the wheel size mode just comes up with three numbers first one only goes to 2
@carter240
6 жыл бұрын
Just a quick question, do you know if the Acewell digital conversion speedo cables would work with one of these so you can get away from mounting all the stuff on the wheel/caliper?
@slim4629
7 жыл бұрын
Does it possible to install this dashboard on my Kawasaki ER5 Twister 99' ?
@antoniononame8482
6 жыл бұрын
Hello thank you for the video but how did you do to plug the account turn its not walking on my motorcycle thank you
@carlosandleon
7 жыл бұрын
how do you set the speedo?
@sencer-sari
8 жыл бұрын
could you please tell me where u used that magneticks for speedometer
@johnbryant2583
8 жыл бұрын
Nice vid, for wiring the the indicators on the gauge, should I follow the wire diagram for my bike, to where I need to splice the ground and power or do I just connect it straight since the gauge has its on power and ground?
@arck76
8 жыл бұрын
hello from the video you see you've wrapped a black cable to the spark plug cable. Where did you get connected? on speedmoteter? thank you
@majstersc9188
4 жыл бұрын
Podłączałem ten licznik w quadzie atv, czerwony przewód to + stały z akumulatora do podtrzymania pamięci, czarny przewód to + po zapłonie, zielony przewód to masa. Obrotomierz ( żółto-czarny) podłączamy do przewodu impulsatora, którego możemy znaleźć w module cdi. W zestawie była blaszka do przykręcenia czujnika prędkości, przykręciłem tą blaszke do śrubki od zacisku hamulcowego, 3 magnesiki rozmieściłem od wewnętrznej części felgi na całym obwodzie felgi.
@davidcormier3673
7 жыл бұрын
I'm wondering if you have the wiring colour coding figured out? I have the same gage and I have an older which has a pink wire and no purple wires. Any wiring help would be greatly appreciated
@roccocroce
5 жыл бұрын
Dude this video Is a HUGE help. I just got this thing lol
@storman7609
4 жыл бұрын
👍 HELLO I HAVE MADE A SIMILAR VIDEO : kzitem.info/news/bejne/tKeir62oap-emHo
@sanketsarkar
7 жыл бұрын
I have some doubts DRugfree1987 - The tacho/speedo I got, has a very short rpm cable. Can I use some other cable to link it and then wrap it around the spark plug cable? 2nd - Is there a way to change the firing cycle? .5, 1 or 2? like 1 pulse per 2 revs, 1 pulse every rev (wasted spark) ... that way. Is there a way to change it?
@RossMalagarie
6 жыл бұрын
Any bar mounting brackets for a Yamaha Raider for this gauge?
@paansukarjo90
6 жыл бұрын
how big is the diameter of the speedometer? thanks
@alanstanfield6121
7 жыл бұрын
ive got the same clock but cant get the gears to show. i connected the wires up from my old clock put them to my new one but wont work any advice cheers
@matthewh9407
6 жыл бұрын
hi. I have a '75 CB360. The neutral light is not on the dial, it's on the middle panel. As far as the visual, can you see the N when not in use, or it is it pretty camelflaged when not lit? Also, the odometer being replaced only has two wires going out. I like that low batt feature on yours. Will that speedo pickup on that automatically, or is it a separate lead? thx!
@netmastyle
7 жыл бұрын
Hi. please clould you tell me the input signal specs to the fuel indicator? i try to may ways but it doesnt works. Thanks a lot.
@apd6750
6 жыл бұрын
Hi! I installed this speedo and everything seems working fine, but when the motorcycle start runing the only thing visible in this speedo is the neutral position. Does anyone have an idea what's going on? Thanks
@williegomez3080
7 жыл бұрын
how did you wired up the speed sensor
@elgrasck8004
7 жыл бұрын
how dou you calibrate the magnets? i got probs with mine ,please help!
@petef.4688
7 жыл бұрын
hooking this up right now but im having trouble with the neutral switch . its a yamaha xv250. i think a circut was completed with the light itself.
@robinbonte
4 жыл бұрын
How did you hook up the gear indicator to the oil sensor?
@nknave
7 жыл бұрын
Hi guys, I just purchased this speedo and my only concern is the wiring for the gear indicator, it mentions that N, 1, 2, 3, 4, 5, 6 are "NEGATIVE GEAR CONNECTION", so I assume it must ground to activate that gear number, but my motorcycle (Vento Tornado 250cc) only sends ground on N while all others are voltage... do I need to build relay fixes for each wire or does this device work with this configuration? Thanks in advance
@Killer1984able
6 жыл бұрын
Is it possible to use one bike's speedo on another bike? I really hate my ninja 250r's speedo and hoping the zx's can be used on my bike.
@severianoromano9410
7 жыл бұрын
I lost the magnets. Can i replace them with any magnets? Or i need a specific magnet?
@fredrikwidegren6112
5 жыл бұрын
Hey everyone, Just bought the same speedometer but are having problems with installing it. Headlight and turnsignals works fine on the display but there is no light on the display (its totally dark). It is connected directly to the battery. Any suggestions?
@MJT-DA
5 жыл бұрын
If my bike revs up to 12,500/ 13,000 would that damage the tach?
@lordmeliodas3259
5 жыл бұрын
having trouble with the sensor can you help me where to connect the 3 wire
@kentonernst3541
8 жыл бұрын
Thank you for the help! Would've been lost for another few weeks. Wiring it on a Yamaha 99 YZF600R.
@storman7609
4 жыл бұрын
Show my videos : kzitem.info/news/bejne/u6uXyKN-hnibiqw
@damianorenzetti
7 жыл бұрын
Hi DRugfree1987! Great video, I found the same speedo and want to mount it on a Honda CM400. May I ask you what tires you have on your bike? I'm absolutely in love with them, but can't find brand and model to see if I can buy them for my CM400. Thanks!
@sajaltandon8319
7 жыл бұрын
hey i have a question, is this universal speedometer compatible with a single cylinder 200 cc bike ?
@sebasti666
7 жыл бұрын
The fuel sensor has two wires. What is the correct way to connect the speedometer to this sensor? I can not get him to walk.
@nhubbers
8 жыл бұрын
Thanks for this video, very helpful!
@storman7609
4 жыл бұрын
👍 HELLO I HAVE MADE A SIMILAR VIDEO : kzitem.info/news/bejne/tKeir62oap-emHo
@LitLMeaNie
6 жыл бұрын
So if your bike does not have a gear indicator does that mean gear indicator on speedo wont work? I have a 250 cc bobber.
@germanobr
3 жыл бұрын
Hi friend! do you know to setup the originals KMs or MPMs before painel instal?
@kyletishkof8886
5 жыл бұрын
Did the magnet fly off when you drove it?
@flavinsapukaya6795
6 жыл бұрын
Hi, do you have installation instructions in Portuguese? I have a cbf 125 thank you
@mbsmmn
2 жыл бұрын
Oops and there blz? Man, I'm assembling this panel on a Moby and I'm having trouble getting the rpm to work, when I turn on pin 9, which is the rpm signal wire to the positive of the cdi, it doesn't work, but if I disconnect the CDI wire but leave it connected the coil only on the panel, when I pull the string to make contact the pointer moves, but if I connect it (coil wire and panel) to the cdi the pointer does not move. Can you help me? The cdi is grounded on the board and the panel is connected to the battery negative, if I ground the battery negative on the Moby board of the short, I don't know if it has to do with the non-functioning with the negative of the panel n being grounded TB in the board as the one from the cdi. Can you help me?
@Xantylon74
3 жыл бұрын
That's for the Video, i'll buy that one. It seems quite good for the money. I did not know how the Tachometer is connected. Are you still satisfied so far? Will the settings be cleared if the battery is disconnected?
@crazypux
6 жыл бұрын
good morning sir i hope you ok i have problem to set up my speedo.how to set up also my rpm don work i have harley sportster
@zachzat1581
29 күн бұрын
How do you get the gas gauge to work when your gas sensor has 2 wires ?
@adnanibrahim4610
5 жыл бұрын
I have installed this on my single cylinder motorbike but accidently i pressed in setting and now i have only two options 2 & 4, how to get back to 1? Is there any full reset option?
@comedianByronKelley3438
5 жыл бұрын
Would this work on a 96 honda shadow vt 1100
@matteomedda9925
7 жыл бұрын
hello I bought it. but I have a problem I can not put the engine speed, it works everything else belonging tours ... I have a transal XL600 ... how can I solve my problem? thank you
@gshok51
5 жыл бұрын
Where did you get that headlight
@user-qv3cr7rz6u
2 жыл бұрын
Could this be integrated into a 2005 honda rebel 250?
@heydude2374
7 жыл бұрын
Hello, will you be helping me? How baglayacag the speed of cable?
@boverkicksass
5 жыл бұрын
DRugfree1987 Hi Mate, i am connecting same unit onto my gl650 honda. I've noticed that your shift position says 6 while mine is 0. I havent connected any whites and my bike isn't meant to have shift position sensor. So i thought if I but a universal one from ebay, would it work. Basically, im wondering how you made gear indicator to work? kr pasha
@randytempleton6633
7 жыл бұрын
I have a 2002 HD 883 Hugger , I have blinkers, N, running lights , High Beams, can't get tach to work or speedometer to work, help..
@darthmaul2036
7 жыл бұрын
mine rpm 'die off' after working for 2 weeks only and the rpm also doesnt accurate(1cyl engine)..about the speedo have you guys get the presice speed?mine not...even i put 4 magnet for also the same..speed doesnt accurate..😥
@Pootus21
Жыл бұрын
How far from center did you mount the magnet? Trying to figure out how to set the speed but mine is way off. Did you use 2 magnets or just one?
@fixall336
4 жыл бұрын
s it true this does not come with TRIP functionality in it?
@shanesheil4033
Жыл бұрын
Were you able to wire for gear reading?
@markaportelli
5 жыл бұрын
Hi all, looking into this speedometer for my cafe racer. Love how it looks and works on the video. What’s your recommendations after installing it? Does it work properly?
@storman7609
4 жыл бұрын
👍 HELLO I HAVE MADE A SIMILAR VIDEO : kzitem.info/news/bejne/tKeir62oap-emHo
@MegaT.
8 жыл бұрын
hello i hawe a problem my rpm meter dont show a right when its working , its shows to mach ,when its works wery minimal its show 4000 rpm , can you tell me how to set number of cilinders 2 , ? i think now its standing to 4
@fozzlebrush1
7 жыл бұрын
All good and working, just confused over the wheel diameter. Do i just measure the rim or rim plus tyre?
@DRugfree1987
6 жыл бұрын
Angus Foster should be wheel including tire
@naavifajrin4502
7 жыл бұрын
i have motocycle used that speedometer but rpm not working....can you give me solution ??? please
@TheMegajupiter09
7 жыл бұрын
Mine did not work as well on fuel. I had to go to the main menu and selected setting 1 to 5. As soon as did hold for the next 5 secs after setting number 5, the speedometer restarted and the fuel reading was working ok. The tricky part is to get it reboot i guess after setting number 5. Its reading full because the resistance or the resistance range is too off. You need to get a multi meter and set it to Ohms (AUTO), and make sure it reads 8 Ohms when empty and 98 when full. This is the fuel sender Ohm range for this speedometer as per the poor manual. Not sure but I guess you can mode the end points of your bikes gauge with resistors to be in the range of this speedometer requirements or else there is a way to to program it maybe to accept different ranges? I am using this speedometer for my personal project and my fuel sender reads around 40+ Ohms when empty and 220+ Ohms when full so i will try to make it to be in the range of 8 to 98 Ohms. If I manage to do it then I will share here. Connections/wiring for those who cant get it right: For the two wires of the sender unit from the tank, ground one of them and the other connect it to blue-white (signal wire) of the speedometer. That's it.
@TheMegajupiter09
7 жыл бұрын
Update: I quickly checked and realized that i have a trim port (tiny variable resistor) , bridged it between the signal line from the speedometer and that of the sender unit and i was able to trim one side that makes sense and that is the empty side. Pushing the sender to the full position would indicate half on the fuel gauge. At least this way you can know half full indication means full and empty means almost to zero or zero it self.
@DirceuCorsetti
7 жыл бұрын
Saeed Al Habsi thanks for sharing that. Have you tried to get the same resistance required at the manual by using one or more resistors in line with the fuel sensor?
@codyalfar
7 жыл бұрын
I have an 84 VT700 (Shadow). I'm tempted to cut down and run without a dash at all, but perhaps you can help me out a little. Did you connect diodes between every dash indicator light (turn, oil pressure, neut., etc)? I have the colored wire that matches up fine with the wiring diagram in the speedo, but there is also what seems like a negative for every colored wire. Neutral light for example has a G/R but there is also a Br/B on the original wire diagram but there is nowhere to put the Br/B. Do I need a diode between the two or how exactly do I wire it up?
@DRugfree1987
7 жыл бұрын
Cody Alfar I'm not sure about your case but I did not need diodes for my install.
@bair395
5 жыл бұрын
where can i get that speedo for my 78 cb750k?
@georgeburns6748
6 жыл бұрын
can this fit on an 07 ninja 650?
@MikeP-ck8bi
4 жыл бұрын
Hey maybe you could help me out or someone in the comments with a nighthawk 550 or 650, so I have the speedo wired up and everything works on the speedo, the only problem I am having is that when I turn the bike it turns on and runs for a little but then turns off, after it turns off it doesn’t turn back on. I’m not sure what it is, I grounded all the ground wires but I left the black and striped brown wires lose, I found that they were positive wires but I have no idea where they go. So my question really is what are the black and brown positive wires on your bike and where did you connect them to?
@storman7609
4 жыл бұрын
Show my videos : kzitem.info/news/bejne/u6uXyKN-hnibiqw
@agpascual7991
4 жыл бұрын
Hows the gear indicator?
@888tonco
3 жыл бұрын
can you change the all km traveled?
@seven7821
Жыл бұрын
Hi just wanna ask how did you make the battery indicator work? What wires did you connect it too?, Because mine is not working. When turning the key on it won't lit up with the rest of the speedometer..
@petersommer5164
10 ай бұрын
i think it's the one he wired to the battery. It's in line with plus and mass on the plug. In the manual it's called battery cathode.
@diegohetfield89
6 жыл бұрын
salve biker! does any of you own the copy of the setting? i missed them! can someone send me the photos? thanks biker!
@williamminton3105
7 жыл бұрын
I have the chinese speedo. How do I set tire science? My front rim is 21". Anyone know the setting?
@1075twist
8 жыл бұрын
so I figured out how to change the 3 digit tire/ wheel size and save it on the menu. The problem is is that all other universal speedometers I have seen have a 4 digit tire diameter code in millimeters. This gauge as you know has only 3 digits. I think it's 50-999. What measurement is this supposed to be? What did you enter based on your wheel dimensions?
@rachelcardoso6676
2 жыл бұрын
Hi, the 3 digits will be the half of your whell size. For example, mine is 1930. So, I should put 965. I hope it helps
@Mytwistedvoices
4 жыл бұрын
I believe the "oil sensor setting" is actually the fuel sensor setting. One of the setting full=0 another empty=0. depends on your bike fuel sensor.
@mattbright423
5 жыл бұрын
You said there is a memory wire that needs to be ran straight to the battery. What color is that wire on the new cluster? Thanks
@storman7609
4 жыл бұрын
Show my videos : kzitem.info/news/bejne/u6uXyKN-hnibiqw
@ohniceness6138
5 жыл бұрын
thanks Dr. Ugfree!
@driftrazor
6 жыл бұрын
How many magnets did you use for the speedo?
@wrbikenchoi6163
7 жыл бұрын
Wow brother! I had a 85 cb750 I bobbed out turned out into a nice bike... but your! Beautiful man just beautiful! I just picked up this speedo for the newest project a 95 zx7r. My pig tails for this speedo and the ones on my bike are the same ones lmao as in both are male ends however the ones on my speedo are female so I'm just gonna switch them
@DRugfree1987
7 жыл бұрын
Jordan Smith I did the same with mine since I was not going to use the only speedo
@gilsonlima2689
5 жыл бұрын
I installed the digital speedometer on a 78 honda hawk CB400 but the coundn't manage to get the rpm working. How can I get it working since this kinda old bike rpm usually works with a cable? I'll appreciate if some one can help.
@watchus020
5 жыл бұрын
Use the tachometer wire that the old speedo was connected to. Check out your wiring diagram.
@marksaile2591
6 жыл бұрын
I have a problem with the wire colors. Anybody can point out which wire is for the RPM?
@fabioalbertogranadosmendoz3344
7 жыл бұрын
Thank you mate! :)
@THEvedaE
7 жыл бұрын
Iam delivered with one speed sensor only. How do i feed the circumference of my 18inch rims???what is unit value, mm or inches?
@foxmox95
7 жыл бұрын
veda E how fix a problem? please help me
@muhammaddarwis
6 жыл бұрын
how much use magnetic steel ?
@DirtyDeeds2191
8 жыл бұрын
I have the same gauge, did you figure out the tach, as I am having the same problem.....Thanks
@DRugfree1987
8 жыл бұрын
see my other video. link will be at the 10 second mark
@AliWaris810
7 жыл бұрын
i want to know how to put magnets, as i do not have disk break, tell me 3 magnets are enough to display accurate speed?
@storman7609
4 жыл бұрын
Show my videos : kzitem.info/news/bejne/u6uXyKN-hnibiqw
@randyperricone5009
5 жыл бұрын
How do you come up with the numbers to put in for the speedo and front tire?
@DRugfree1987
5 жыл бұрын
Tire diameter. A good way to do it is, put a tape measure on the ground. Then line up the valve stem with the beginning of the tape roll your bike till you get to the stem again. Then convert the reading to mm
@IHaveManySkill
5 жыл бұрын
Hey DRugfree, can u say me Pinouts from the Kabel (red,yellow,blue, ..... ) ? I got the same Speedometer but i dont know the pinouts witch colur is witch siganl .... This would be awesome ! Best wishes Tim Braunbarth
@DRugfree1987
5 жыл бұрын
Someone in the comment section commented what the wires do. Or check out my other video detailing what wire does what
@thealchemist5230
8 жыл бұрын
Helpful vid, what did you put in for the speedo numbers, the info I have seen says the circumference of the tyre, in my case 120/70 17 is approx 1860mm but you can only put in 3 numbers! Do you have to put in the amount of magnet pickups? The oil sensor is the fuel sensor 1=100 Ohms and 5=500 Ohms depending on the sender you have in the tank.
@DRugfree1987
8 жыл бұрын
+The Alchemist I still haven't dialed in the speedo yet. but I'm using both magnets. right now I think its at like 777 and its off by a few mph
@thealchemist5230
8 жыл бұрын
+DRugfree1987 But then 777 is way off from 1860 how have you got to this number? I could do with understanding this, where have you fitted your magnets, how far are they away from the spindle?
@jamtJrus
8 жыл бұрын
+The Alchemist The wheel circumference divided by number of magnets, if you have 1 meter circumference and two magnets you have 1000mm / 2 = 500mm. I have 5 magnets on mine so for me the same circumference would be divided in 5 = 200mm
@jsppagtalunan1345
4 жыл бұрын
do you know how to reset this? because its asking id?
@rorygibson8818
6 жыл бұрын
I’m a bit late to the party on this one. However, I am hoping to confirm that these external speedometers not only come with display units but also are supplied with the necessary equipment to calculate the speed of the bike i.e. magnets that attach to the wheel and the fork to work out the speed? Also, does anyone know if these are road legal in the UK? Thanks
@storman7609
4 жыл бұрын
Show my videos : kzitem.info/news/bejne/u6uXyKN-hnibiqw
@kientrinh111
7 жыл бұрын
Hi, I'm bought this speedometer for my yamaha yb125sp, everything seems right but I can't figure out how to make the rpm work? Could you please help me?
@huynhkienvu1996
5 жыл бұрын
kiên trịnh hi bạn, bạn đã xử lý được phần báo tua chưa? Bạn mua ở đâu và giá bao nhiêu thế?
@ghawrot1
7 жыл бұрын
Hi buddy. I have just have a question about pod filters. Did you have to adjust the carburators for them? rejet them or enything like that? thanks
@DRugfree1987
7 жыл бұрын
yes. I had to rejet the carbs. wasn't a easy task but I finally got them running smooth
@ghawrot1
7 жыл бұрын
DRugfree1987 ca you give me so advises or discripton. If you gonna keep it secret I understand. thanks
@tonnguyen7618
8 жыл бұрын
wow thank for making this video
@marinaforova3644
3 жыл бұрын
*Only 18* 👇👇👇 250961.loveisreal.ru
@T.J163
7 жыл бұрын
how do you set the miles back to what the bike was on before you changed it?
@DRugfree1987
7 жыл бұрын
TERRY JOLLEY no. I rebuilt the engine so it was pretty much like new anyway
@mateopopovic23
8 жыл бұрын
question for you.fuel wire not respond to contact with negative.same with rpm wire does not respond even I have wrapped around spark cabel . i tried with second gauge and its same.all other light.gear shift work just fine.i do t understend
@DRugfree1987
8 жыл бұрын
+Mateo Bimbo are you sure they are not mixed up? other than that I'm not sure what it would be. grounding the gas light will only keep it from flashing. and I still haven't got my rpm gauge to work perfectly. sorry I couldn't be more help
@jamtJrus
8 жыл бұрын
fuellevel has a built in delay so you might need to keep it grounded for a few seconds before it starts moving
@majdcccx
6 жыл бұрын
How to connected fuel indicator?
@davidbufflier7174
7 жыл бұрын
Hello, What is the color of the counter wire for the turn count (RMP) thank you
@DRugfree1987
7 жыл бұрын
mine was purple. the coloring may have changed from when I bought mine
@milanpamuki4720
8 жыл бұрын
Does it fit for a 1990 Kawasaki GPZ 500, which has 16" wheel?
@DRugfree1987
8 жыл бұрын
+Milán Pamuki I have no idea to be completely honest.
@justinduncan2480
7 жыл бұрын
Hi I just bought this speedometer and the eBay seller didn't include full instructions. Your video has helped with some of my questions, but now I'm curious about the margnets. The speedometer sent to me has three magnets. Does the speedo use all three or are they sent as spares?
@DRugfree1987
7 жыл бұрын
Justin Duncan of I remember correctly. to get it set up right you have to measure the wheel in mm. then if you have 2 magnets you will then divide that number by two. and if you use three magnets you divide it by three that's how you get the number you need to put in the tach for wheel size. that helpef
@jamtJrus
7 жыл бұрын
It is like DRugfree says, BUT! the more magnets you use the faster will the gauge respond to changes in speed, I have 5 magnets om my bike
Пікірлер: 471