If you think this is cool…you’ll love the video with Sterling Marlins 1995 Daytona 500 winning car! (Side note if anyone has some Brodix 867 Pontiac heads they’d sell…email us 😂) Stapletonautoworks.com
@c.johnweir182
2 жыл бұрын
Ha. I love the history of cars how they ran and how they raced.
@gooseflatwaterfowlers
2 жыл бұрын
Would High Compression 327 heads with Sodium filled valves work?
@ezekielduvall9752
2 жыл бұрын
Frr I was already like man he needs some poniac heads in the when I was watching the vid😂 sure it helps the sound with the valve angle and all
@lewismocaby3646
2 жыл бұрын
A-1 Performance warehouse in Monmouth Illinois has two sets for sale. Saw them listed on eBay for $750 for a set with 2.125 inch dia intake valves and 1.60 exhausts and the other set was $500 but I didn’t look into the specifics on that set other than looking at the pics. The pics of the cheaper set looked like the chamber’s were pretty oxidized but that’s really no big deal. If you end up getting either set of those heads, look into getting the matching intake to go with them. Been down that road myself with 18 degree small block heads. The 18 degree stuff I use has a raised runner and different bolt pattern than factory 23 deg sbc stuff and the flange and bolt holes are also different angles than factory. If you want a setup that can really flow some air, I mean serious velocity with good volumes they’re the way to go. Had to hop back to the message to say I made it to the end, nice collection of exhaust parts. About the Penzoil, I’ve just always had good luck with it in my flat tappet engines since my first sbc. Been so many years since I looked up the specs on their oils but I do remember reading about the zinc content in theirs which is the reason I still use it for flat tappet stuff. Oils without the lubricity and imbedment of that zinc kill lifters in no time followed by the cam very shortly after.
@TheJagjr4450
2 жыл бұрын
A set of those heads with Titanium valves ran about $20,000 in the early 1990's. I was an apprentice from 18-21 in a race engine shop from 1990 - 1993 and we did high end class exploitation for guys running short tracks. 5/8-3/4 mile short tracks. We ran zero gap rings and only the top ring sets with short compression height pistons and the longest rods we could put in the engine.
@rontronnesjr
Жыл бұрын
Absolutely love hearing the "old timers" tell their stories of stretching the rules.
@Stapleton42
Жыл бұрын
We do too!
@brandnew2848
2 жыл бұрын
More of this type of content is needed, men like these are not going to be around forever so their stories need to be heard. Keep up the good work.
@jasonhastings5538
2 жыл бұрын
The storys these guys could tell!!!!! Id sit for hours just to learn from them!!!!!
@fatpatlives1998
2 жыл бұрын
They need to go to DEI and find out what they found for them plate cars in 2000
@1mccarson
2 жыл бұрын
100% this is great
@Foryourinfo369
2 жыл бұрын
Absolutely
@operatorsolidsnake2542
Жыл бұрын
I agree completely!! I've been eating up this content!!!
@gr4eme1975
2 жыл бұрын
That was an epic amount of work on those heads and intake. One of my buddies was crew chief for a touring car team in the 80’s. He told me they had a turbo heat shield that was designed so that you could remove the turbo without removing the heat shield as the scrutineers would put seals on the bolts before the race weekend. So once it was sealed they would then swap out the turbo for a larger one and race. Well one weekend they win and the car get pulled in for inspection. They are in the inspection building knowing that they have an illegal turbo but it’s getting late so the scrutineers tell them they will inspect first thing before they race again on Sunday. My buddy is stood at the back of the shop by a window which he casually yawns stretches out his arms and unhooks. The scrutineers usher everyone out and secure the building for the night. Once dark my buddy and another mechanic sneak back and climb in through the window and proceed to swap that turbo back to stock and leave. The next day the scrutineers are looking the engine over knowing something isn’t right but find nothing so the car gets released lol doesn’t matter what the firm of racing everyone is doing something to gain that advantage without getting caught lol
@Cynsham
Жыл бұрын
Just like with breaking the law, it ain't illegal to break the rules, it's illegal to get CAUGHT breaking them
@kentuckyblugrass
2 жыл бұрын
I don't know that we can fully appreciate the amount of knowledge these McClure videos have given us. The engineering, R/D and testing that these guys did/do is absolutely incredible. These videos are priceless 🙏🏻
@cheerdiver
Жыл бұрын
You guys really love sophistry. Want the truth, come back and look at my comment from two weeks ago.
@alfee9411
8 ай бұрын
Amazing job Larry and Crew 💪👏
@SteveLowe65
2 жыл бұрын
You two getting to sit with these legends and hearing their stories firsthand is absolutely priceless.
@Stapleton42
2 жыл бұрын
Thank you Steve!!
@matthewhicks1725
2 жыл бұрын
Makes me Jealous!😜😜
@brianbeilmann2992
2 жыл бұрын
Hell ya agree. Your comment about putting that in the trophy room just so you can see it all the time. Agree. And so the Logan’s car is blue…..
@ryanbrown4336
2 жыл бұрын
I would love to sit around for some of their stories , the shop tour video really shows their progression in Nascar . The #4 Kodak car is such an Icon of the times when nascar was at its peak . I miss those days but I remember them like it was yesterday. You and Logan are the dynamic duo keeping the history alive , thanks guys.
@matthewhicks1725
2 жыл бұрын
@@ryanbrown4336 agreed. But it seems like back then. We didn’t see the inside of the shops that much. It was all a mystery. Unless u saw them on an episode of “Inside Winston Cup Racing” on a Sunday Morning on TNN. But it still showed very little. Maybe the cars sitting all lined up. So all this is New and Amazing. Finally getting some questions answered!!😂
@alienworkshop37
2 жыл бұрын
I’m still amazed how this history is just sitting out there. It’s great that you get to these guys before they’re gone. These stories are amazing
@DanO1234567t
Жыл бұрын
The simplicity of the engine, but the extreme attention to detail makes this so fascinating. Throwing money at it doesn’t always work, and the nascar rules really made the fab guys think about every aspect to grab any HP they can. Tuning and fab work is such a joy to do.
@timothylovern1850
2 жыл бұрын
Good to see younger people enjoying the real history of NASCAR keep up the good work
@dannotwalruslarkin9324
2 жыл бұрын
Everyone used to get so pissed at Nascar for knowing teams had an advantage & not doing more to find it. These guys did just enough to disguise their advantages and it's absolutely hilarious to see & hear more about it thanks to you and Dale Jr. I'm just glad Nascar record books are set in stone & they aren't throwing a fit about the stories that have come out in public the last 4 or 5 years.
@Stapleton42
2 жыл бұрын
Thanks not walrus man!
@silkysixx
2 жыл бұрын
It looks like the center chamber is a plenum. If you'll notice, the outer diameter of the centre bore interferes with the four outer bores of the intake tracts. The carb would sit above the divider, allowing each runner to share the center bore as an additional volume to their runners. What you have, here, is a carb space below the carb flange! Now that is ingenius.
@JustinSmithPYRO
2 жыл бұрын
Awesome analysis 🤘🤘 I was thinking something like that too. It truly is genius. These guy's are legends, with their motor builds
@twoblacklabs904
2 жыл бұрын
Silky, EXACTLY. The center bore acts like a combination Venturi “collector” and funnels air downward, making the engine inhale and “breathe” deeply. It was genius…and so were the engineers who perfected it.
@pat36a
2 жыл бұрын
I think the space between the carb. and inside the intake was a restriction. He said the closer you could get the center plug to the Carburetor the better. That's why they came up w/ways to fill that void. Air flows faster in a solid tube then 1 w/a big void . A smoother path for air will flow more air .
@Toxic2T
2 жыл бұрын
@@pat36a Wow.
@xmo552
Жыл бұрын
How does that spring in the center work?
@vtd3271
Жыл бұрын
I’m glad to see that you have access to all of these great racing legends and that you can share portions with us, great content always
@Stapleton42
Жыл бұрын
thanks man we are glad you're here for it!
@tealtazmanian966
2 жыл бұрын
I've been Building and Modding engine since the late 60"s and learned from a local that used to help on some different NASCAR Teams cars. He made it clear that the heads and intake are more important than the pistons or block. He taught me how to weld heads and then he'd mill them to different angles like these guys did...once he just milled the head on the intake side more to build more compression and that helped his drag Camaro gain 2 seconds with just that...He did that kind of experimental stuff all the time and would make one change at a time then do one more change...some failed so he'd build another head up to the failing point and then try a different trick. HE had more in his head than about any other engine builder I ever knew and I'm 74 now. To answer your OIL QUESTION; I've tried several brands and found it all depends on the engine size and how it's going to be raced. I found EDGE works best for my 97 K1500 and MOTUL 7100 works amazing in my BMW. I did use Pennzoil in a VW Buggy a while back but I sold that toy...that was the only thing that used Pennzoil tho for me..Pennzoil used to have a pretty bad REPUTATION when they used Paraffin Wax for a while. Boy it helped old and tired engine for a while but they would build up sludge from blow-by in short order tho. I think engine builders experiment with different oils like they do different parts. It is an ongoing experiment for me and once I find a slight advantage with one brand and viscosity then I keep that for THAT ENGINE. It usually shows up in the 1/4 mile engine more so that other forms. It can just come down to less vibration with one oil over another....there's nothing wrong with staying with one oil tho....I love taking the time to find something just a TAD-BETTER tho...just like tweaking each valve to fit the head..........I'm sure you get that. Oil is just that LAST little TWEAK for this Ol' Engine builder...LOL It's all in the MINOOTE LITTLE DETAILS when it comes to one engine over another with all the identical parts...any builder will understand that being identical doesn't mean they're the same, same by any means. BTW. I enjoy your channel but get so busy with life that I forget to watch every week...don't take that offensive tho. Ya gotta remember, I'm 74yrs old and not into the internet as much as the younger generation...LOL
@donaldgminski8621
2 жыл бұрын
Great story. And that, to this day, "heads and intake" being more important, seems to be lost on many. Especially the current 20's kids. They'd rather spend $10-15k to let someone else make their power for them, instead of learning.
@tealtazmanian966
2 жыл бұрын
@@donaldgminski8621 I know GROWN MEN that do the same thing. I may have about $7,775 in the Carburated Engine & Trans I built for my '97 C1500 long bed that STILL beats my buddies Mustang with an Injected PERFORMANCE $29K Engine & a $5,700 Trans he bought just to "Now I'm gonna Smoke your Truck". I'm pretty sure that His equipment MAY technically be able to beat mine but he and his crew just run and run and run it without EVER checking anything but the fluids. I don't think they know how to do anything to it or May just be they're all TOO intimidated to touch anything. HE is actually my BEST friend but he wants to do HIS CAR HIS WAY and doesn't let me give them Any Advice,,,I can Dig-IT! WE just have AWESOME LAUGHS with all of this and never let it get too serious or RUN our lives...After-All, We're only here for a little while so may just as well have Good-Klean fun with it all...RIGHT-ON? Have a Great Day and keep the Dirty Side Down Donald Gminski. Signed, A new Friend, "Auto Doc"
@mikepate6404
2 жыл бұрын
You don’t get the inside information without a lot of effort to get it and you deserve a lot of credit for the effort. We get to enjoy the history so thank you.
@jeroddbock
2 жыл бұрын
Thank you for this!! This is the history of nascar that needs to be shown!!! All the "mechanical innovations" that happened!
@BillySinnz
2 жыл бұрын
The amount of welding that went into those heads and intake is just insane!
@sprngrdave
2 жыл бұрын
Unbelievable History. I Love watching this kind of Technical stuff. Thank You for these Videos. These Gentlemen & the Knowledge they have is Unbelievable
@cool62chev
2 жыл бұрын
I certainly appreciate the amount of work the went into those heads and intake.
@jeffscott1287
2 жыл бұрын
I continue to love your true NASCAR historic videos. Maybe one day NASCAR will return to the roots that made them successful. I moved to NC in 1988, and my memories are great. North Wilkesboro was my absolutely favorite track.
@rustloversgarage
2 жыл бұрын
This time period was the beginning of the end for the racing I grew up doing and watching. Glad to see the McClures are doing well!
@thomasbritton640
2 жыл бұрын
I'm 71 years old my dad an auto marine repair shop and business I've been a motor head my entire life and nascar fan since 1967 nhra fan since 1968 Jungle jim and David Pearson were my first favorites then Earnhardt then Dale Jr Martin Truex because I grew up around and with his dad and uncle what im getting at is im an old guy and you and your beautiful girl friend have old souls I have a grandson born in 96 so im impressed with your passion I enjoy your work and want to give you a big THANK YOU its not every day a person can make their passion their job !!!
@jeremiahjohnson6583
2 жыл бұрын
Now we are talking. All those secrets of speed that hopefully get done on the Monte Carlo. Those intakes are so interesting looking. This is the stuff I can dive into. I love the mechanical side of racing. You guys made my morning
@Stapleton42
2 жыл бұрын
I want to find some of those Brodix Pontiac heads 👀
@jeremiahjohnson6583
2 жыл бұрын
Those Brodix heads are so awesome. My dad has them for his 69’ GTO and he said they are like gold to find and he loves them.
@shawns57garage
2 жыл бұрын
I was huge Ernie Irvan fan and first race I got to go see he crashed minutes before arriving at Michigan … I remember all the merch trailers were shut down and everyone thought he was dead. This MMM series of videos is quite the treat ! Thanks for sharing 👍👊
@jimmy_olds
2 жыл бұрын
I wrenched on an ARCA team in the late 90’s through the 00’s, James Hylton helped us quite a bit and we returned the favor (if nothing else, we were young, exuberant and most importantly free labor😅). Especially in the early days, James always had racing buddies who’d come out of the woodwork for the race weekends. Those old dudes had endless racin’ stories, about out smarting the NASCAR or ARCA officials. Those two remind so much of James and his friends, brings back a ton of memories.
@jeffvanhorn69
2 жыл бұрын
It's so hard to fathom, the endless hours of welding, grinding, and porting just in the top end. Wow! Thanks for bringing us all along on this journey, true car guys appreciate it. God Bless.
@JustAGuyWithALongScreenName
2 жыл бұрын
Loved Ernie Irvin as a kid. Shitty couple of years for me though. Was a period where either my driver's were either dying or retiring. Ernie Irvin, Davey Allison, Harry Gant, Allan Kulwucki, and Richard Petty. Finally caught a break with Dale Earnhardt. Guess you can figure out why i finally gave up on finding a new driver and quit watching NASCAR in 2001.
@TheZmt325
2 жыл бұрын
This is so cool. This was the peak of me being a nascar fan. I was 10. That win made me a swerving ervin fan. Seing that stuff up close is awesome!!
@ronmurphy9819
Жыл бұрын
History should not be forgotten. I love it and to me it’s a great way to not repeat it!
@matthewarnold5246
2 жыл бұрын
Was in for the whole thing. Dad drove Cale Yarborough’s hauler a couple of times in the early 90’s. Richard Perry’s Busch team hauler as well once or twice. I believe Bob Johnson was the crew chief. Dad had a friend from our home town that invited him to help drive on the west coast trips.
@gregnelson6450
2 жыл бұрын
J.E. Beard who they mention doing the intake was my fiancés brother. He could build some engines for sure!
@cruechief24
2 жыл бұрын
Made it man. Crazy someone born in 1996 has so much content on pre-birth NASCAR era material. But it doesn't matter. Rock on. Escalade sounds badass!
@cadeshetter8168
2 жыл бұрын
I was born in 93. I grew up in a racing family and have even raced some myself. This channel has made the history and cool memories of these old school racers come out and enjoyable for myself to enjoy
@deanrobinson7956
2 жыл бұрын
I'm 62 and I love your show. The secrets of the past revealed. Watching those guys smile about the old days
@Stapleton42
2 жыл бұрын
Thanks dean welcome to the channel!
@juleso9
2 жыл бұрын
I'm blown away with what these guys did to that top end. I came to your channel for the drag racing, stayed for the Nascar history and knowledge.
@jaimesonritter3375
2 жыл бұрын
hearing/seeing all the tricks and ins/outs of cheating or getting a competitive advantage on those old cars is insane. More content like this is needed!
@TheRuffusMD
2 жыл бұрын
this is great for history . my first race was the 1962 daytona firecracker 250 . .. i love this , and this story needs to be preserved . thanks for the work
@BabyJake426
Жыл бұрын
I don’t get to watch all of your videos, start to finish, but everything I’ve seen that you produce is AMAZING! Thank you for sharing your passion with all of us!
@Stapleton42
Жыл бұрын
thank you so much! We appreciate those contributions greatly
@jasonjackson5493
2 жыл бұрын
Eric: how did that work? Larry: "worked good" 😂
@dannypowers4995
2 жыл бұрын
I was at Talladega in the 90s when Sterling got down a lap or 2. Gordon got down a lap . Gordon hooked up to Sterling's bumper and Sterling pulled Gordon a full lap back up to the leader's. The crowd was blown away with the speed the 4 car had Love this stuff.
@bobbellow5502
2 жыл бұрын
I was there as well. That car was FAST.
@UFC_Buffalo
2 жыл бұрын
I made it to the end. Man, I just love this kind of stuff. My Godfather raced small time Street Stocks and Midgets in the 80s, 90s, & 00s, and I could just listen to stories from him and his crew chief forever.
@W.H.Slater-49Fordlightning
2 жыл бұрын
Mitchell you and Logan do an excellent job. I'm 99% sure that I've watched every one of your videos on both channels all the way through no matter what it's about. I'm definitely an OG on here my friend you guys are killing it.
@Stapleton42
2 жыл бұрын
thanks man
@michaelpage1796
2 жыл бұрын
I ran across your channel a few weeks ago. Totally love these videos of how NASCAR used to be. I was. South Carolina state trooper for 25 years and worked Darlington races for 15 years. I remember the different sound that the #4 had in ‘91. Keep up the good work.
@Stapleton42
2 жыл бұрын
Thanks man!! We are glad you’re here
@MThompsonjr115
2 жыл бұрын
I love this stuff. I used to work with SRT to develop intake manifolds for the MOPAR prostock engines. I love engine history and all the small tips and tricks these guys did to make horsepower.
@dennislamers986
2 жыл бұрын
I was an Ernie Irving fan. I love the back stories and the we never cheated stories. Thanks again for doing this. I hope this Interview opens other doors.
@ryanbrown4336
2 жыл бұрын
Ernie was always a favorite of mine , it kinda hurt the way he exited Morgan McClure . I understand about bettering yourself but don't ruin a team owners chance of winning a championship just to get out of team.
@travispeoples
2 жыл бұрын
I started using Pennzoil after we bought a vehicle that recommended using a high detergent oil to keep the engine clean. Pennzoil advertises their oils ability to keep your engine clean, so I started using it. Years later a friend of mine who is a race car builder, driver and mechanic mentioned he uses Pennzoil because of an experience as a young mechanic. Basically he was doing a cam swap on his bosses truck and he couldn't believe how clean the engine was for the mileage, his boss had used nothing but Pennzoil in his truck and my friend has been using it ever since.
@Stapleton42
2 жыл бұрын
That's awesome!
@gilbertlindsay3507
2 жыл бұрын
Wow that was probably the most eye opening video I’ve seen on KZitem. Thank you both and the Morgan-McClure crew. DW was my Oprah, after he retired I latched on to Mark Martin. I ran Mobil super that was in the 80-90s because that was the only oil that didn’t turn colors in my sbc. When synthetic oil became more prevalent I ran Mobil 1. Now I run Brad-Penn in my hotrod and European oil in my VWs. Thanks again.
@ktmbmk66
2 жыл бұрын
I’ve been waiting for this video since you teased it. I love old nascar engine tech. Please do more vintage engine stuff. Interview engine builders, hunt down the engines and parts, get in depth with the tricks and secrets. Thank you.
@craigcontofalsky4387
2 жыл бұрын
I'm 69 years old and I remember all those cars from those years. A big fan and a ex drag racer from the 70's. I used to watch Gapp and Rousch Pro Stock Maverick! I raced a 71 Duster 340 Super Stock car that had Chevy valves in the 340 Mopar heads. I really enjoy all the technical stuff you review. Thanks!
@Stapleton42
2 жыл бұрын
thanks Craig we are glad you're here!
@Jeffbambam
2 жыл бұрын
I made it till the end ,Morgan McClure built some bada$$ rides ! I love to see the ingenious ideas these men did to create an advantage. There's some much to learn from these great creative minds and I'm thankful that you are picking their brains and sharing the tidbits they are willing to share, to me these guys are the magic of racing .
@garypankratz9352
2 жыл бұрын
Your videos are fascinating. I could listen to Larry’s stories all day. Keep ‘em coming.
@BIILLETT
2 жыл бұрын
I love what y’all do!! Please keep it up. This history that you are sharing with us is peak of NASCAR to me. It was the best time for drivers and also the very best for the self made engineers behind the scenes. Thanks again.
@qwaszxpolkmncvb
2 жыл бұрын
Y'all do some serious interviews. I stopped watching nascar several years ago but it was a family tradition I participated in for the first 30+ years of my life. I love the content.
@Stapleton42
2 жыл бұрын
Thanks man!!
@mikejaxn
2 жыл бұрын
Used to love driving by the Morgan-McClure shops along I-81 on the way to Bristol back in the 90's - it was obvious for several years they were doing something different and effective with their engine program along with some great driving by Ernie and Sterling. Thanks for this, lot's of answers to questions I asked myself years ago...
@Stapleton42
2 жыл бұрын
Thanks man we are so glad you’re here!
@Chuck_Carolina
2 жыл бұрын
My understanding of it is when you change the length of intake runners to each cylinder you end up with lean and wet holes (cylinders); ideally you want to tune the the carburetor and all the holes run the same - so the engine would be in balance in all 8 cylinders. That is the perfect world and an engine tuners wet dream. Remember, the Holley carburetor we ran back then were not in balance between the front metering block (Primary) and rear bowl metering block (secondary) circuits. You play with the jets, air bleads, accelerator pumps, power valves, air horns and squirters to fine a balance with a Holley carb with any manifold. What these smart guys crafted here was a tuned tunnel ram out of a modified single plane Edelbrock manifold for a restrictor plate rule book world in NASCAR.
@davidmagruder4779
2 жыл бұрын
Very cool video. I remember all the rumors and stories about this team, their cars and engines but it is so neat to get it from them. Thanks
@galyerfamily8201
2 жыл бұрын
As an Australian/Kiwi living just down the road in Greenville SC I love this stuff. They’re such unassuming good old boys that liked to build cool stuff. So cool that you’re sharing it with us before it’s all gone.
@fish4kbcf
2 жыл бұрын
Made it to the end. Best NASCAR content on KZitem. Super cool to see a channel uncovering all of this history.
@John1Brady
2 жыл бұрын
Amazing. I remember following the car magazines talking about restrictor plates and feeling anger since it obviously seriously cut power and I was all about making MORE power! Thanks for the chance to hear from the guys fighting for power!
@justinshearer3016
2 жыл бұрын
i love the engine parts, and tech and i absolutely love the loose rule interpretations that they had to figure out to run in the front. please more engine/cylinder head stuff with the guys who worked on them
@michaelgideon8944
2 жыл бұрын
Thanks for sharing a restrictor manifold. I have always wanted to see the inside of one of those. The oddity of the design of the baffle is really interesting. The center tube is totally unexpected. I would have thought the holes would have a large entrance radius.
@GreyMulletMan
2 жыл бұрын
This is great. I was always a huge Ford fan but I always cheered for the Morgan McClure guys because they were located so close to me. Good stuff!! Thank you!!
@littleoakey32
2 жыл бұрын
Very cool stuff seems like yesterday when I was watching Ernie Irving win the Daytona 500 definitely fun times
@chrismadaj8751
2 жыл бұрын
This was really cool learning about the older nascar ENGINES liked it a lot
@carlbruhn1772
5 ай бұрын
The brilliance hidden in these guys minds is incredible. The trial and error philosophy is ingrained. A room full of engine builders and crew chiefs from that era would make a Nascar history documentary second to none.
@DimMakTen31
2 жыл бұрын
The intake work is all about keeping the velocity up. If you went from the small restrictor bores into a big open intake plenum your velocity would drop a ton. same reason they raised the floors in those runners in the heads. Keep that velocity up all the way down to the valves into the chamber.
@shitbox82
2 жыл бұрын
Back when nascar engines still sort of resembled a production SBC, I enjoy hearing about the R&D they put into the engine programs back then. 👍🏻
@jfreddy9370
2 жыл бұрын
That was an awesome look into some old school NASCAR tech! I had no idea they used Pontiac cylinder heads on that race car. Thanks for letting us see all these great encounters you and Logan experience. 🏁
@skittlecar1
2 жыл бұрын
It's definitely interesting. I think all the GM teams used the Chevrolet small block, but each division had their own heads. I knew about the Pontiac heads, didn't know about the Buick heads. I'd imagine Oldsmobile had their own also. I also didn't know you were allowed to run Pontiac heads in a Chevrolet bodied car. Neat insight for sure.
@mikedonzero2692
Жыл бұрын
@@skittlecar1 they were no more Pontiac heads than the man on the moon lol. Trust me they only had the word Pontiac cast into them. HVH aka HI Velocity Heads was Joe Patel. He prepared the vast majority of cylinder heads for almost all of the GM teams. The restrictor plate could be over come to a large extent by getting the Cowell air ( at the base of the windshield shaped right) air pan would feed the carburetor & at 180 mph it could be worth 90 hp.
@MM_in_Havasu
2 жыл бұрын
Excellent video! Was out of town but am watching this now, sure do appreciate the historical value of the contents here, and I'm on it today! Thank you & Logan for all you do. 😎👍
@andrewdipierno2131
2 жыл бұрын
JUST GREAT!!!!!!! When BILL FRANCE says to please DONT STINK UP MY SHOW!!!! You’re making HISTORY!!!!!!!!
@Stapleton42
2 жыл бұрын
bingo 😂
@OGOutdoorGarage
2 жыл бұрын
Of course I watched until the end:) Great documentation of an amazing group of engineers!
@openoutlaw
2 жыл бұрын
Can't wait to see the new headrs for the Monte. Awesome look at the heads and intake off the #4 car. I had no idea they were Pontiac heads.
@jeffgraham48
2 жыл бұрын
I've seen every 4 car Daytona victory live. Really cool to see stories behind historical nascar races and wins. Those dudes had it figured out!
@haroldkellermier5502
2 жыл бұрын
My wife and I were over there in 91 when Ernie won -- my wife was so impressed she actually fell asleep in the stands LOL!
@Stapleton42
2 жыл бұрын
😂
@jimmysharpe8067
2 жыл бұрын
He mentioned JE Beard who ported their intakes he was a personal friend of mine and taught me quite a bit about porting heads and intakes. He was a hero of many young engine builders and racers in the area where he grew up in Wilson NC. He passed away a few years ago sad time for many in the nascar engine building Community.
@PHMadness
2 жыл бұрын
The port work on those heads was done by Mike Chapman. I built drag racing heads at another shop, but I learned sooo much from him and his guys. It was a BIG deal when Irvan won that race.
@kentmcmahon6481
8 ай бұрын
The heads were built by EPD racing heads
@dubiousf00d
2 жыл бұрын
This could have been longer. Very fascinating to see the engineering involved with just the engines. I was very young when that car took Daytona. So cool to see some of the inner working. Thanks!!
@jeffbergen4612
2 жыл бұрын
We always watch your videos to the end Mitchell. Wouldn't have it any other way. Man, just imagine the amount of work that went into those cylinder heads and intake - as this was (more than likely) done completely by hand, without the benefit of CNC machining, computational fluid dynamics, and all the other modern technology available today.
@terrypoe4211
2 жыл бұрын
It is so cool to go back and see the extremes that these very ingenious people could do and create and run on the ragged edge of the rule book. Awesome stuff keep up the good work.
@sarahbecker1267
2 жыл бұрын
This was so informative. Thank you for taking the time to show the background of the real NASCAR.
@wesleybateman5837
2 жыл бұрын
Cool to see all that went into building the full intake on restrictor race engine
@pawtasticdadof532
2 жыл бұрын
Wow, it’s exciting to just see the historical parts, and listening to the stories told by legends!!! No One has ever done what you two have filmed.
@ronwells5935
2 жыл бұрын
This kind of thing is so intriguing . I just turned eighty one years of age and have been a Nascar fan since I was about ten years old. I grew up outside of Asheville, NC. Banjo Matthews who lived in Asheville was my childhood hero and the king of western North Carolina racing. How I wish you could have known him, unfortunately he passed away about the time you were born. The stories he could have told about the racers he had known would have been fascinating. Thanks for documenting all this before it gets any later. Additionally, you are a wonderful interviewer in that you don't take a pat answer for anything. Love the way you keep probing till you and we are satisfied with the knowledge we now have. Great Job. You two, please keep up the good work for us all.. Ron
@karljacobson6174
2 жыл бұрын
It would be great if you get Runt Pittman to do and interview with you, he was the true genius of all these innovations that were talked about.
@rolandtamaccio3285
2 жыл бұрын
I think it was RP that built those very high compression engines .
@PYROPACKRAT
Жыл бұрын
Thanks youngens , love what you do. I've been a huge racing fan for over 60 years and yes I'm in the 70's yr old
@Stapleton42
Жыл бұрын
Thank you sir!!
@33LeRoy33
2 жыл бұрын
Hell yeah Brother!! We undeniably miss out on all the best years in NASCAR history! Which is why this kinda content really clicks with me!!
@sirwilliamroark3175
2 жыл бұрын
I absolutely love learning about the true history of not only Nascar, but racing as well. I have always looked for horsepower in unconventional ways in all of my "stock" street cars. I thoroughly enjoy working on cats even though life has never led me in that direction. I would love to take a trip and maybe get to do a walk through of your garage, the same as you did here. Love the content and secrets that you have been digging to find! Keep up the hard work. God bless!
@bradjohnson9671
2 жыл бұрын
This was VERY interesting. The NASCAR guys did some incredibly clever stuff back in the day. They still do. What they figured out without the tech aids we have now is amazing. There are so many little things the one would never think about. Like a drive shaft driven oil pump back at the differential to circulate the diff oil through it's own cooler. The oil would get so hot the seals would fail... I'm a new sub now. Well done.
@Vlad-nw8rx
2 жыл бұрын
Thank you so much for sharing this and basically preserving history by picking all of these old school guys heads. Speed TV wishes they could have gotten an interview with all of these guys and the stories they tell. What you are covering is NASCAR when it was good. I was born in 85 so I did not get to catch much of it but up until it dropped Winston as the sponsor my dad took me all over the southeast to races and it is the most fond memories I have of my dad. It has become too technical and computer driven these days and the days of a stock car are gone sadly. I would have just loved to be in a shop, even just as a fly on the wall, on a wednesday evening drinking a few beers and working to get a car ready for the weekend and listening to all of these old school guys trying to get as close to illegal as they could without going over the line lol. They sure knew how to stretch that rule book or either hide the stuff so good if it was illegal that the officials never noticed. This was truly the good ol days
@Jim-op3kg
2 жыл бұрын
That was really interesting not only the history of the heads and intake but the tricks they did to get more power
@bikewurks1757
2 жыл бұрын
Bro.............you are literally doing the shit the media should have done 30-40 years ago.............thank you
@Stapleton42
2 жыл бұрын
thanks man!
@kerryhickman2235
2 жыл бұрын
I love hearing the things they would do to gain any little edge that they could get over the rest of the teams. Y'all do an outstanding job with this channel & the history of racing! Thanks for all the hard work!
@homebrewracer
2 жыл бұрын
I appreciate all these videos. I have worked in the NASCAR since 05 and love seeing this stuff from the cars that I grew up watching. Sure is different from the junk we have now.
@armorgeddon
Жыл бұрын
I'm curious, why do you think what you have now is junk?
@homebrewracer
Жыл бұрын
@armorgeddon you can't fix problems in designs. The quality control on 95% is out of your hands. The only thing you can change are shims and slugs. No one got in this sport for that. You got into Nascar to always strive to make a better mousetrap. I know a dozen guys that left before and after this car. It was at the biggest team in the sport. They left because you don't do anything at the track anymore. Practice is a joke now.
@travisshephard5491
2 жыл бұрын
So cool to see those parts up close and to hear what they did to make them a dominating set. Thanks for taking the time to video it and share it.
@shaneanderson2156
2 жыл бұрын
This channel is absolutely awesome! huge NASCAR fan for over 40 years. I love the tech stuff! Keep it up and I look forward to getting merchandise and seeing the rest of your videos! WELL DONE!!!!
@Stapleton42
2 жыл бұрын
Thank you Shane!!
@boredcnj
2 жыл бұрын
This is best content on KZitem !!!!! This history should be told and you 2 do an awesome job sharing this stuff. Keep it up 👍🏻🇺🇸🏁
@martinharrelson6389
2 жыл бұрын
Thank ya'll for another great video. A very special Thank You to Mr. McClure for sharing these closely guarded secrets. This was innovation at its finest! These were the golden years of NASCAR. Now, NASCAR micro manages things to discourage innovation and I think it has really hurt the sport. Anyway, thanks for the memories!
@gam3rk1d981
Жыл бұрын
Those heads and intake sure is cool love to see history like that.
@glenedwards3038
2 жыл бұрын
All I can say is go time for you two lucky people to see and feel racing history like you do… great great great vids of history that without you and the better half show all of us… just very lucky to be there for stuff no one else has went to the limits with showing the untouchable past… wonderful!!!!
@battlestar7779
2 жыл бұрын
Yep, I’m still an Earnhardt fan for life (Sr. & Jr.) , but I have always respected Morgen-McClure guys , because they really know their stuff- especially super speedway/ restrictor plate racing. I knew Earnhardt always had his hands full, when it came to the big tracks, when Morgen-McClure was there. I personally think they were Earnhardt’s (and R.Childress) biggest nemesis at a Daytona win.
@charlescross4393
Жыл бұрын
I guess in the end he was his biggest nemesis no fault of his own though. Dale made his own fate sadly.
@battlestar7779
Жыл бұрын
@@charlescross4393 No - that wall was his biggest nemesis - and it’s not prejudice.
@bowtieguy6870
2 жыл бұрын
Another great video! All of us old school fans are very fortunate you guys had the foresight and willingness to pick up everything and move across country to try to do this stuff. I’m sure it was scary but it has worked out great for us and I hope it has for you as well. I hope Nascar and people in the industry appreciate it as much as I do. Thanks again!
@Stapleton42
2 жыл бұрын
Thanks man. Almost a year now since we got here!
@loudog1547
2 жыл бұрын
i used to love NASCAR in the 90s!!! i was born in 88 and my sunday was always me glued to the couch and watching the race no matter which track they were at. I still remember watching the daytona 500 at home seeing Dale hit that wall and keeping MW out front for the win. wasnt until a couple hours later after my father getting home and telling me that he ended up passing front his wreck. after that idk what happen but i slowly drifted away from NASCAR racing. still have love for it and would love to get back into it!!! i love what you do on your channel here and is amazing to see and learn all this unknow stuff to the regular race fan lol. love the content bro keep it up!!!!
@dansimpson6247
2 жыл бұрын
When I came across your channel around a year ago maybe a little more, I was like ok another LS channel but I subbed anyway. You have set your channel apart in the most unique, creative and shall I say historic way!? Lol. Good stuff you two, I really appreciate the thought and and effort you put into your content, keep it up I'll keep watching.
@Stapleton42
2 жыл бұрын
Thanks Dan! Those days were just doing anything we could to get by. This stuff now is where the real passion is
Пікірлер: 1,5 М.