My excavator, ("VOTE" Brand), has the pull start cord assy removed and a piece of duct going tight to the side panel, drawing fresh air by the engine flywheel fan/impeller allowing for positive air flow into and out of the engine compartment. Thanks for making this video. Good luck to you!
@JohnnyThrobber
3 ай бұрын
Several commenters, here, seem to believe the fans are 12" fans. They are 7 inch fans. I have almost the same machine, and a 12" fan would never fit in those areas. I can guarantee that those are 7 inch fans. I hope this is helpful information.
@shanerogers488
2 ай бұрын
Nice video. One recommendation…get that plastic off your seat. Took mine off right after buying it and the seat bottom was covered in mold and rust. Thanks for the video!
@MrTunalic
Ай бұрын
I would also recommend extending your exhaust pipe, before the muffler, to re-locate the muffler outside of the engine enclosure. Also, wrap the exhaust pipe in exhaust pipe shielding, to minimize the heat radiating inside of your engine enclosure. Use a reflective insulation on the bottom of the seat.
@DOWHATIWANT
10 ай бұрын
Just wanted to say "THANK YOU" as I did this to mine as well with fusible (15a) inline link. Also added aluminum heat shielding around the exhaust, gas tank, and full sheet under the seat. Changed all new American zerks also. Works Great.
@restoration-projects
8 ай бұрын
once you dial them in they are solid machines
@georgeharvey3062
7 ай бұрын
Great job! Thanks for sharing. Looking to buy one of these minis so the upgrade is nice to know.
@socalplanedoc
11 ай бұрын
did the exact same thing to my QH12.. both pulling air in, works fantastic
@georgezhou7961
Жыл бұрын
Great Video. The manufacturer should add at least 1 fan to those small excavator. 🎉
@frankp215
Жыл бұрын
If both fans are blowing out of the machine it would would seem to be most efficient to me.
@raymondmonty4321
10 ай бұрын
He was probably trying to create positive pressure
@jaybrown651
8 ай бұрын
Frank. You are right. With most cooling systems on almost everything, the goal is to extract or pull the heat from the area. But any air movement I'm sure is a definite upgrade.
@Jeremy-fy1sz
3 ай бұрын
@@jaybrown651 Nah. With an air cooled engine, you want to get cold high velocity air to the engine, sucking out the warm air is way less effective and recirculates a lot of cold air. Ever tried to inhale the air over a hot beverage to cool it down? Nah, because it doesn't work. Same thing with a hair dryer. You can blow a piece of paper around from 6ft away with the high velocity air, but if you try to suck anything from more than a few inches, you're out of luck.
@lifeoncloud9172
14 күн бұрын
Would it not suck in hot exhaust? That’s why I think he wants them sucking in through the sides and out through the back.
@anonymous_friend
14 күн бұрын
When building high power computer towers. You have cool air pulling into the case through lower front fans and pulling air out of the case at the top rear of the case. This seems like the most effective way to cool. I'm no engineer though 😂
@kingfloopy
Жыл бұрын
Thanks for the video. I am going to wire mine up with the harness for a LED lightning system with a switch.
@郭晓东-b2t
Жыл бұрын
Good Job, friend, It is nice machines. I purchased one about a month ago from Denny. I had mine shipped down to TX. It works perfect the work I do.
@R94GC
6 ай бұрын
just posted a video to my channel of me testing one of these mini excavators with a TMK 150 tree sheer. I was mind blown how well it handled 5-6" diameter trees!
@inthebackyardwithdel438
8 ай бұрын
Nice clean install !!!
@ronkuzyk3836
Жыл бұрын
Would it not work better with one fan pulling and the other pushing to create a flow rather than two fans pushing against each other and negating flow? The fact that you removed the back panel shows that this does not work as well as hoped. Since they are bi-directional fans it would be an easy experiment.
@GarrettGalloway
10 ай бұрын
I'd say the grate on the back of the cover has enough holes that the fans aren't really going to be fighting each other. If these two fans were covering the only grates in the machine, one puller and one pusher would certainly be better. In this case, it probably doesn't matter and it'll prevent the fans themselves from being completely heat soaked.
@bigtxbullion
10 ай бұрын
@@GarrettGalloway👌 that back has plenty of air flow gap
@kencooper2059
9 ай бұрын
I'm curious if your battery is holding up? I believe the charging circuit is only 10 amp on that engine, and the fans draw about 6.7 amps each, so theoretically running both would drain the battery over time.
@restoration-projects
9 ай бұрын
Iv had no issues with charging, it appears to be keeping up with the demand
@MM-ys3hm
Жыл бұрын
Thank you for posting this. May I ask what amperage the fuse is?
@dougadams9419
6 ай бұрын
This is what my QH12 looks like, but it's Orange.
@raybird2535
11 ай бұрын
No relay?
@austind6546
6 ай бұрын
Thanks for the video
@paruggeri
10 ай бұрын
Are they both flowing air the same direction
@restoration-projects
8 ай бұрын
yes both blowing air into the engine bay
@jaimeceja4114
9 ай бұрын
What size fans you run?
@restoration-projects
9 ай бұрын
7 inch 12v off amazon
@ericjohnson9080
8 ай бұрын
Thanks for this.
@restoration-projects
8 ай бұрын
Absolutely
@janramonmartin
Жыл бұрын
These only have petrol engines in America, for the rest of the world they are diesel and don't need additional cooling
@dalethornton1113
11 ай бұрын
Thanks to our environmental extremists, the Briggs and Stratton is the only motor to pass emissions unless you want to get the Kubota diesel which doubles the price.
@f.hababorbitz
11 ай бұрын
@@dalethornton1113 I kept contacting different eBay sellers that indicated the Vietnam engine Kopu KD192F engine in their listing description, but when asked about the engine they all edited their auctions to show it was a B&S. So the EPA change must have just occurred. Sucks damn it. I'm waiting for a delivery on one from the AGT sellers in Chicago. Watched many videos here that had only positive things give the cost. Only negatives I found were from dealers that were pushing their branded product.
@dfk8881
11 ай бұрын
Yes most US buyers are now getting the Briggs gas engine, cuz the Koop or ChangChai 1-cyl Diesels are not EPA- or CARB-compliant. In the latter case, the main flywheel fan is ducted to the outside to bring in cool air. Most of the makers have not bothered doing this with the gas engines. I did for mine when I bought it 5y ago from China and installed my own gas engine. If you use an internet search engine, you will find pix of how I did it. Utube is great for vids (see mine for the XN08), but does not allow commenters to respond with pix. The automotive electric fans do move a lot of air, but some of the gas engines, like my Duromax 420, do not put out enough current to power them. The B&S alternator puts out more current.
@markygrove6311
7 ай бұрын
Couldn't follow how you wired fans together and went to fast. Can you go slower and steps better?
@dougadams9419
6 ай бұрын
No link in the description to the fans.😡👎 That's why you got a Dislike.
@TupperLakeGaming
15 күн бұрын
If you don't have a Pull - Push setup for the area you're cooling the setup is completely useless, if you're pulling air in.. And not pushing it out, the air is just stagnant. It's the same with a computer case setup
@bman6502
7 күн бұрын
So are you recommending one brings air in and the other pulls it out??
@TupperLakeGaming
7 күн бұрын
@@bman6502 Correct, You want air to be transferring though the engine compartment, not just being blown on the engine. You could technically have a push-pull setup also! It's the same theory, just turn the fans the other way. I would opt for a push-pull setup considering you're taking the air from the outside, cycling it though the engine, while the other fan is pulling the hot air from the engine out.
@steveelmes8568
Жыл бұрын
Great idea. Where did you buy the fans. I recently got an excavator very similar to yours and would like to do the same thing.
@billykulim5202
Жыл бұрын
those are standard radiator car fan 12v i believe, you can buy those in any car parts store
@skeller0160
2 ай бұрын
Amazon sells a 200 watt flexible solar panel (100 watt at harborfreight) for $80 that could either keep the battery charged or power another fan, and the panel fits perfectly on top of the sun canopy.
@denslod2930
Ай бұрын
If you change the rotation, I believe you have to flip the blade around.
@pfeifferrealestate
3 ай бұрын
Has that worked okay having a fan on each side blowing on the motor, Any issues since you have done? Also, what gauge wiring did you use? Thanks
@dalecasal9468
Жыл бұрын
Nice they moved the hydraulic tank forward now. H12 it's where your cup holder is. I've found with one fan it pushes a lot of heat up under your feet.
@griz5178
2 ай бұрын
so did it make it cooler
@stevem2266
10 ай бұрын
Where did you get the fans? And what size are they 12inch ?
@paruggeri
10 ай бұрын
Wouldnt they be hot all the time if it was connected to the starter
@paruggeri
10 ай бұрын
How are the fans working out blowing air into the engine compartment.
@raymondmonty4321
10 ай бұрын
Probably trying to create positive pressure
@restoration-projects
8 ай бұрын
they work great, provides a constant breeze over the engine
@dalethornton1113
11 ай бұрын
Are these 12 inch fans? Wondering what is the largest size that fits to maximize the effect.
Пікірлер: 57