Fantastic learning, as always, Keith! You definitely take a lot of the fear out of doing these repairs and I always learn a lot from your videos. Greatly appreciated, thank you!!
@joro8604
2 жыл бұрын
When you use rope, make sure a knot would be smaller than the spark plug hole. i did this on cylinder two, and the rope knotted on itself!!! Tried everything, but eventually had to take the head off to get the rope out..... Tool works great.
@FlyinMiataVideo
2 жыл бұрын
Oh yikes. That's learning the hard way.
@RolandByrd
2 ай бұрын
This video was a godsend! Thank you!
@FlyinMiataVideo
2 ай бұрын
Glad it was helpful!
@VirginiaPatriotRebel
3 жыл бұрын
I definitely need that tool, makes the way I've been doing this process seems prehistoric.
@davidcook1394
4 жыл бұрын
Nice vid as usual. Couldn't help but notice the gen 1 CRX with what look like Ronal R10 wheels. I've been a Honda Tech since '84 and remember installing a Mugen body kit and wheels on a first gen CRX , an HF if you can believe it.
@FlyinMiataVideo
4 жыл бұрын
That's a proper 1985 Si in the background.
@AlexTrull
3 жыл бұрын
Great tool. Looks far easier to use than the 'for any engine' types I've seen. And takes up a lot less space to boot.
@shadowraith1
4 жыл бұрын
Thanks for the lesson.👍
@z2xtra783
Жыл бұрын
Awesome video thanks 🙏🏾
@FlyinMiataVideo
Жыл бұрын
Thanks for watching!
@ChristianSarnecki
4 жыл бұрын
Quick question, Will I need to buy new keepers for new valves? I assume the old keepers have been “bedded in” by the old valves, thanks!
@FlyinMiataVideo
4 жыл бұрын
There's no relative movement involved so there should be no wear. No need to pick up new keepers!
@jacklandismcgowan1413
4 жыл бұрын
Great Info...thank you 👍
@nissan_motors4934
Жыл бұрын
Would putting the piston for whatever valves your working on at the top of its stroke be a viable option too? As opposed to putting rope in the combustion chamber, or using a leak down tester
@FlyinMiataVideo
Жыл бұрын
That will allow the valves to fall partway into the cylinder before they make contact. Too far down to be useful.
@DavesWoodFloors
8 ай бұрын
My 92 smokes on start up but then quits once it warms up.? Any ideas of what it needs .?
@FlyinMiataVideo
8 ай бұрын
It sounds like your engine is burning something it shouldn't. Start with easy stuff first: Compression test, leak down test, are your spark plugs super oily, etc. Try to find something out of the ordinary.
@shadowraith1
4 жыл бұрын
Any advice on pressurizing the oil system without starting the engine?
@FlyinMiataVideo
4 жыл бұрын
Unplug the coils or pull the main relay.
@tgy119
4 жыл бұрын
@@FlyinMiataVideo is it good practice to do that after an oil change?
@FlyinMiataVideo
4 жыл бұрын
@@tgy119 There's no need. The oil pump should still be primed. If you pre-fill the filter, pressure should come up immediately.
@fredfartstones5171
3 жыл бұрын
To prelube / pressurize the oiling system (after a rebuild): remove oil pressure sending unit (next to oil filter). Force 2-3 quarts into the 1/4 NPT hole. I use a HFT paint pressure pot. $89 well spent, it has other uses when combined with a vac pump.
@grahamcrane83
2 жыл бұрын
Any tips or advice for doing this on an ND2 without the tool and the head in place??
@FlyinMiataVideo
2 жыл бұрын
Without the tool, it will be considerably more difficult. If you're doing it with the head in place - regardless of the tool - you'll need something to keep the valve from falling into the cylinder. Either fill the cylinder with compressed air using a leakdown tester or fill the cylinder with rope or something fed through the spark plug hole. We prefer the first option.
@tgy119
4 жыл бұрын
You didn't show us how to install the valve seal.
@FlyinMiataVideo
4 жыл бұрын
It just slides over the end of the valve stem and settles on to the guide.
@kingofwestpalm6350
3 жыл бұрын
Does your dual valve spring kit come with valve stem seals?
@FlyinMiataVideo
3 жыл бұрын
It does not, but we do offer valve stem seals if you want to replace them at the same time.
@justsaiyansteve
3 жыл бұрын
I want one!
@TiredoftheBS1562
Жыл бұрын
Collets not keepers..... please
@nanta278
3 жыл бұрын
Does the tool fit nc miata?
@FlyinMiataVideo
3 жыл бұрын
This particular valve spring compressor is specifically meant for use on the NA/NB BP engines. It will not work with an NC, sorry.
Пікірлер: 35