Nice video. Ir read is working fine but while using Ir send pin3 is used here ,where is it mentioned pin3 in the code and how to change it
@maciasergio
3 жыл бұрын
same
@maciasergio
3 жыл бұрын
maybe it is defined by the library, but it would be ok to be said, or even teached in order to change that.
@TuprogramaciontvEsp
3 жыл бұрын
I think it's coded in the IRremote library. If you take a look to the IRremote manual arduino-irremote.github.io/Arduino-IRremote/ it says: "You can use any pin for sending". At the end of the page there is a table with the pins to use with different arduino devices.
@markusaurelius4015
3 жыл бұрын
you’d have to go into the IRremote library itself and change it there. You can trace through it yourself. For example, your code likely includes IRremote.h So look in that header file. You should see a section on “sending.” It’ll probably reference a “.cpp” so go into that. You should see references to using pin 3 there.
@sameerk12982
4 жыл бұрын
Thank you very much for this helpful video...exactly what I was looking for .....appreciated.
@BlueSayamanHey
3 ай бұрын
Well done thanks
@omarharbah6972
5 ай бұрын
I bought Roku remote but doesn't work with my tv, can this work with it?
@alexflorin04
4 жыл бұрын
Hey, I have a 2ohm rezistor and that's all I have right now, can I use it instead of the 100 ohm one?
@fahadahmed480
3 жыл бұрын
nice
@turgayayyldz2172
4 жыл бұрын
I've been researching this topic for a long time. I have not seen anybody else who has told so simply. Thank you.
@subhodeep2012
3 жыл бұрын
where u defined pin for ir send?
@davelovell8631
2 жыл бұрын
I think that it is defined in one of the libraries.
@VELVET462
21 күн бұрын
i just want to control my TV Lift position 1 and position 2 in a custom made panel which i will integrate into my studio desk. Is something like this possible with a IR arduino? or will it not work well when not pointing on it like with a remote controller?
@RandomlySelectedUserName
3 жыл бұрын
idk whats wrong but somehow sender shows that its sending some commands by its own (but in reality it doesnot) and it spams like that untill i stop proggram :/ and in 1 start up i can send only 1 command after it stops working
@kajusmakalius296
Жыл бұрын
umm, the sender is not working, and i dont see pin 3 defined anywhere in the send scetch, im quite new so qould you explain?
@vargasmakery
6 жыл бұрын
that's awesome! i was just wondering if it would be possible to do it on an esp....... another thing is if you can incorporate to home assistant? great job on the videos look forward to seeing them
@_emanmodnar
Жыл бұрын
A nice tutorial … really annoying with music in the background!
@DriesJanssen-i7j
9 ай бұрын
Can someone make this for a raspberry pi as well?
@tblank79
6 жыл бұрын
Awesome video man! Keep it up. Are you an Engineering student? I noticed the lab notebook. If so, looks much better than mine!!! Haha
@Grensom
6 жыл бұрын
Haha yes I am an Electrical Engineering student. And believe me, I only made my notes so neat because I am sharing them in the video, otherwise it might not even look English..
@anokhautomation4453
2 жыл бұрын
Can you please explain how we can send the hex code manually from the serial monitor without hard coding on Arduino.
@Su67377s
4 жыл бұрын
I want to make a remote controller on Arduino (IRrecv+IRsend+sleep). In which it should read IR data usingtsop1738 then send the desired IR data using IR transmit led. And when no data is received it should go to deep sleep to conserve battery. Because I want it to run on 3v lithium coin cell. I found many codes on the internet using Irsend + sleep or just IRsend + IRrecv. But not a combination of all the three. If you make the code for the same it will be helpful. Need for this project=== some channel nos on my tv are 4 digits. It is very difficult to press 4 keys. So my plan is to press only 1 key tv remote and my controller will send desired 4 distinct key codes to tv by sending cancel command to my 1st command press by me on my tv remote
@ytuser1985
Ай бұрын
6 years old video but still proving to be very useful for my application where I am trying to control my speaker system with TV remote.
@sameerk12982
4 жыл бұрын
Can you please tell me where is IRremote.h file?
@w.schumann4372
3 жыл бұрын
Press Ctrl + Shift + I to open up the library manager and search for the IRremote library, then install version 2.8.0.
@aayushyeola9879
2 ай бұрын
@@w.schumann4372 thanks for the version info, wasted my 2 hrs debugging an error that never existed. Thanks
@TheSalarKhan
6 жыл бұрын
This ...simply... works!! Thanks!
@777kinev
4 жыл бұрын
Куда светодиод подключить?
@Jandroverse
2 жыл бұрын
Awesome video, just one comment. For the IR transmitter the 5V is not needed in the schematic and the whole circuit could have been done on the top rail saving you an extra wire going from negative top rail to negative bottom rail.
@giannissotiropoulos3721
3 жыл бұрын
Hello, thank you for your video its very helpful. Right now with my code i can only turn on my tv..can you help on how to turn on my tv wait 5 seconds and then turn off again? i tried writing the power code under the delay again but it didn't work..thank you in advance
@nuwang1
6 жыл бұрын
Hey if anyone had a problem with using a TSOP1738, it wasnt working for me. I wired it differently and voila.. Right most wire should go to arduino pin 10 or whatever, left most pin to ground and mide pin to 5v! That should work if u had same problem as me, i was using a different ir receiver to the one on the video, that may be why.
@emircan3823
5 жыл бұрын
Can we use both the transmitter and receiver at the same time?
@kyrkas2008
3 жыл бұрын
Man thanks a LOT!!! This was the solution to my problem!
@firdoshdiakus4841
3 жыл бұрын
Can you help me, I don't see any cable connection between the Rx & Tx boards?
@JibunnoKage-cj2kz
11 ай бұрын
So this all 5v for VCC?
3 жыл бұрын
Each button of my air conditioner and TV remote is worth more than 1. what could be the reason?
@bektasar5058
3 жыл бұрын
hello i try your scetch on mega.but doesnt work.whats the problem?
@bektasar5058
3 жыл бұрын
hello good project bravo.i cant see define transmit pin on scetch.pls help me .i use mega .
@catherinemccann3715
6 жыл бұрын
Is there a way to set up a security system for your home using voice actived, your voice not Alexa...so that way it would recognize your voice to deactivate the alram or activate it..what I'm stating, would like a remote access on my phone to unlock my house by my voice..or eye retna..
@الكبيرقوي-س6ل
5 жыл бұрын
thanks, it's a nice video brother
@ARTTM143
6 жыл бұрын
You’re one handsome guy
@andrewklaudt8080
6 жыл бұрын
Looking forward to your next video!
@VayunEkbote
4 жыл бұрын
My remote gives a different codes each time for the same button
@adamszuczynski2786
4 жыл бұрын
thanks man
@mRendyIrawan
4 жыл бұрын
I’m not that familiar with arduino, but I assume this sketch would work too on a nodeMCU or a wemos?
@samuelsantanam
6 жыл бұрын
Nice! thanks man.
@ilkeraykut7064
5 жыл бұрын
Thank you for the video.I wanna ask you something.How can we increase the range of the transmitter LED?
@nicoclompen
5 жыл бұрын
The range of a transmitter LED is always set to a certain range, you cannot increase or decrease this. My best guess is finding a different transmitter LED with a better range!
@markusaurelius4015
3 жыл бұрын
I believe you can technically alter the amount of current being sent through the IR transmitter but check the datasheet as there will be some range of what’s acceptable for your diode.
@ayhamkattan3947
4 жыл бұрын
I don't understand how the transmitter work without selection his pin
@nikomose
9 ай бұрын
10/0
@AsratMengesha
6 жыл бұрын
Using IR Signals to Control TV 4,963 views I appreciate the technology: Infrared, Xray, MRI and other similar thechnologies. But, I discourage the dumbization theories, such as infrared light ...etc.the empty fiction theories (Infrared is just above red light???) , Infrared from the sun???? fuck that lie. Thanks. We know light is not electromagnetic for electromagnetic signal is man made technology signals. Communication is not light technology, communication /remote control...is just result of technology.
@w.schumann4372
3 жыл бұрын
The only "dumbization theory" here is the one you presented good sir.
@firdoshdiakus4841
3 жыл бұрын
Where is the connection between the Rx and Tx board???????????????????????
@Eloy_Antony
Жыл бұрын
Sending pin /pin 3. is not in the ir send code?
@dewisugihartiningrum5500
Жыл бұрын
i have same curiosity too
@andreasn23
2 жыл бұрын
Nice tutorial tested and it works for communicating between 2 arduinos one Transmitter and 1 receiver
@cookieemonstah
5 жыл бұрын
I've tried using the LCD screen but it needs like 11 pins, right? Whew...
@patrickm9953
3 жыл бұрын
Fantastic Video.. Got my IR receiver working in Minutes !
@nyashamurairwa986
2 жыл бұрын
What is the maximum resistance you can use for the IR transmitter
@lendeamihaela
3 жыл бұрын
Ir led not working. I try with an other code and work, but it's not what I need. Can you help me?
@jackraven8711
2 жыл бұрын
hey, just wondering if you ever sorted this out? as i have the exact same issue.
@shrinidhiachar8790
4 жыл бұрын
Which version of arduino ide are you using??
@thefuturetechnologychannel
3 жыл бұрын
Nice video sir , I am your fans
@johnmacd2001
6 жыл бұрын
great project. Why are you using an arduino and the ESP8266 nodemMCU? Can't you do all this with just the ESP8266 NocdeMCU?
@Grensom
6 жыл бұрын
johnmacd2001 Yes I will probably put up an Updated Video doing this
@pranavsundriyal1251
4 жыл бұрын
Can u please tell me why you wrote", 32" after writing each remote code?
@Grensom
4 жыл бұрын
Pranav Sundriyal The 32 is to show the size of the hex value. So for something like 0x24A54F33 each hex digit contains 4 bits. So 8 digits x 4 bits equal a total of 32 bits
@Klagerh
2 жыл бұрын
LIKEEE , COOOOL !!!!!
@user-pj6uj9mw6o
3 жыл бұрын
My ir sender is not working
@ROHITPANSARA007
4 жыл бұрын
oh I am really looking for it Thanks
@rozberry8867
4 жыл бұрын
Really annoying music.
@DanielHernandez-op4fl
3 жыл бұрын
Wonderful ! Lo ve it
@vijaysigh5098
2 жыл бұрын
Thanks bro, this is amazing
@ivanprincipato
4 жыл бұрын
Awelsome video , thank you 🙏👍🏻
@Gudspella
4 жыл бұрын
This is useful with pc monitors right?
@tyronedeshaun7717
4 жыл бұрын
If you have a remote for it, yes.
@shrinidhiachar8790
4 жыл бұрын
I can't compile the sketch
@marcoantoniobatista5564
5 жыл бұрын
thanks! minus one Indian vid to watch
@hayderqaso5232
3 жыл бұрын
it's working thanks 🔥🔥🔥
@angooparsons
6 жыл бұрын
Could you make this with a micro bit?
@allenpallath
5 жыл бұрын
Can I use a 2pin ir receiver for the same??
@megasko590
4 жыл бұрын
great video
@habiburfalioglu
5 жыл бұрын
hi, we use the 3.pin for the transmitter, or where we can change the pin number, thanks.
@markusaurelius4015
3 жыл бұрын
@Federico Blum you’d have to go into the IRremote library itself and change it there. You can trace through it yourself. For example, your code likely includes IRremote.h So look in that header file. You should see a section on “sending.” It’ll probably reference a “.cpp” so go into that. You should see references to using pin 3 there.
@tvjmohan
4 жыл бұрын
nice brother....
@johnmellor6065
6 жыл бұрын
great video GRENSOM
@joakimjocka8022
5 жыл бұрын
Can the ir transmitter be any led or it is specific
@jonathanpini
4 жыл бұрын
an ir transmitter is not an LED it has to be a transmitter
@adithyagj8289
5 жыл бұрын
Thanks a lot It was very useful But if I hold the button continuously the screen displays only Fs Could you help me out
@zacgreene9425
5 жыл бұрын
FFFFFFF just means that it is detecting the same button being pressed multiple times, the other numbers/letters are the hex values
@earlsnider4377
6 жыл бұрын
Hello thanks for video but I'm getting an error exit status 1 Error compiling for board Arduino/Genuino Uno. What am I doing wrong here?
@matthewfogel8447
5 жыл бұрын
every time it prints 3 lines of FFFFFFF, every once in a while it will be something else but rarely. what should I do?
@adithyagj8289
5 жыл бұрын
Matthew Fogel hifi same problem Good to know I’m not alone
@matthewfogel8447
5 жыл бұрын
@@adithyagj8289 I've tried to look it up too and I can't find anything. I'm guessing the receiver module is just bad quality :(
@cmkee6645
5 жыл бұрын
wrong data pin connected?
@matthewfogel8447
5 жыл бұрын
@@cmkee6645 no its all connected properly
@matthewfogel8447
5 жыл бұрын
@@adithyagj8289 were you ever able to find a solution? im still stuck
Пікірлер: 108