KZ
item
Негізгі бет
Трендинг
Журнал
Ұнаған бейнелер
Ең жақсы KZitem
Фильм және анимация
Автокөліктер мен көлік құралдары
Музыка
Үй жануарлары мен аңдар
Спорт
Ойындар
Комедия
Ойын-сауық
Тәжірибелік нұсқаулар және стиль
Ғылым және технология
Кіру
Тіркелу
Кіру
Тіркелу
Негізгі бет
Трендинг
Журнал
Ұнаған бейнелер
Ең жақсы KZitem
Фильм және анимация
Автокөліктер мен көлік құралдары
Музыка
Үй жануарлары мен аңдар
Спорт
Ойындар
Комедия
Ойын-сауық
Тәжірибелік нұсқаулар және стиль
Ғылым және технология
Негізгі бет
Ғылым және технология
Using MQ5 Gas Sensor with Arduino
Күн бұрын
Using MQ5 Gas Sensor with Arduino
Рет қаралды
9,088
Electronics Eternity
1
1
Жүктеу
Пікірлер: 26
@ibrahimerol157
3 жыл бұрын
I did two different MQ5 set with your video. In same environment, both give different values. What can i do about that, what is the problem?
@electronicseternity9210
3 жыл бұрын
You can try leaving the MQ5 ON for an extended period to season the sensors
@ibrahimerol157
3 жыл бұрын
@@electronicseternity9210 thanks for attention . i m going to try now.
@sahilv2570
2 жыл бұрын
Can I know the name of the wire used there
@electronicseternity9210
2 жыл бұрын
I guess you're referring jumper wire
@sahilv2570
2 жыл бұрын
@@electronicseternity9210 yeah thank you 💜
@breeze9402
2 жыл бұрын
the arduino turns off when i plug the gnd to gnd and vcc to 5v pls help me
@electronicseternity9210
2 жыл бұрын
Check if you're Arduino is working. Then test your gas sensor. If your gas sensor, you might have to replace.
@electronicseternity9210
2 жыл бұрын
Try adjusting the calibrator as well
@breeze9402
2 жыл бұрын
@@electronicseternity9210 i checked the arduino and its fine it probably my gas sensor
@scientistBENIELSLAB
3 жыл бұрын
Good
@electronicseternity9210
3 жыл бұрын
Thank You :)
@kingdanvers
Жыл бұрын
Buzzer not working
@kevinpotenciano9383
Жыл бұрын
Can I see the codes
@electronicseternity9210
Жыл бұрын
Refer my blog in the comment section
@kixbix3292
3 жыл бұрын
Please give the code
@electronicseternity9210
3 жыл бұрын
Hi, Code is in my blog
@kixbix3292
3 жыл бұрын
@@electronicseternity9210 i m getting error by this code please help me out
@kixbix3292
3 жыл бұрын
Do we have to use any library??
@electronicseternity9210
3 жыл бұрын
@@kixbix3292 No library is needed. What is the error.
@kixbix3292
3 жыл бұрын
Alarm was not declared in scope, exist status error,error uploading to arduino
Пікірлер: 26