Damn. I think I better just save up for this service.
@Townie_au
2 жыл бұрын
Excellent video. Straight to the point. No BS. Showed all steps. Thanks mate. Subscribed.
@tonychettleburgh8953
7 ай бұрын
Wow! what a professional mechanic, the way he takes everything off and puts it back on in the same place etc. Just glad I don't need mine done, what a ton of stuff to remove and put back, no wonder it costs a fortune but thumbs up to a proper job.
@ToddTube1
4 жыл бұрын
I think I'll just sell mine when the warranty ends.
@jan-willemvandenberg1769
3 жыл бұрын
I was thinking te same 😂
@monnom9641
2 жыл бұрын
Thanks for this video...... you helped me make my decision....... I wont let nobody play in my engine unless obvious problems. Last time i paid 600$ for a valve adjustment was on my gsx1250fa and.......engine noises appeared 1 month later....... (and the engine was runing perfectly before the adjustement)
@marks4058
2 жыл бұрын
Please get your valve clearance checked by a professional! Do not skip this important maintenance. If you do not have this done, your engine is very likely to be damaged and the repair will be very expensive. In my experience this model of engine often needs shims changed after 40 to 50,000km and Kawasaki recommend checking more frequently. If you do not have the shims checked and changed, the exhaust valves will be burned and the engine head may be damaged.
@robmut1357
4 жыл бұрын
Wow! Excellent video! You must be a professional mechanic or if not you easily could be. Very nice work.
@marks4058
4 жыл бұрын
Thanks for the compliment!
@lendiatube
5 жыл бұрын
Nice work! !! Nice video !!
@turbotyoma
3 жыл бұрын
Awesome job, man!
@fredjunca
4 жыл бұрын
Merci pour cette vidéo et bravo pour votre travail. Quelle dextérité et quelle précision 👍👍👍 Impressionnant
@marks4058
4 жыл бұрын
Merci pour votre commentaire. J'espère que cette vidéo vous a été utile.
@fredjunca
4 жыл бұрын
Mark S Vidéo passionnante surtout. J'aurais vraiment totale confiance en vous pour vous confier l'entretien de ma moto (1200 Bandit). Vous êtes tellement soigneux !! Malheureusement les mécanos compétents comme vous sont très très très rares ... Encore bravo pour votre travail 👍👍👍👍👍
@mementomori4972
Жыл бұрын
Thank you good Sir! See you again after another 24.000 km!
@zombiebiker5581
4 жыл бұрын
Now that is a lot of complicated work,good job you are mega fast 😝😜🤪👌👍😏. Well done my man. I think my versys 650 is half as easy. Now all I got to do is be as quick as you 😇😜
@blackmasiyach
4 жыл бұрын
I came here thinking I could pick something up but now I realized there's lots of work need to put into this, I guess I will have to skip this project . Good video though, you're a Pro
@marks4058
4 жыл бұрын
It's definitely a decent chunk of work, somewhere between 6 and 12 hours depending on how fast you move. I recommend having the service manual handy and re-reading it as you go. Take lots of photos and label parts and locations as you remove them. Make sure you vacuum + wipe all around the head cover and frame before you open it. You also definitely need to have a torque wrench and removable threadlocker (locktite).
@randygreer5491
Жыл бұрын
Did that job once, will have to do it again as I just bought another. :)
@Davidlouis3
2 жыл бұрын
Crazy just had mine done on my gsx 1250 fa at 21500k well worth the £500 at Suzuki dealership oil, coolant, plugs etc also
@abhinay2911
2 жыл бұрын
Marvellous
@Davidlouis3
2 жыл бұрын
Brilliant
@CHRISTIANBEARIVER
8 ай бұрын
Great!
@rubanowicz
3 жыл бұрын
Super
@jacrancam
2 жыл бұрын
That’s a lotta work
@InfoMTOC
2 жыл бұрын
Hello Mark, where did you get the manual from?
@jmiddle818
Жыл бұрын
I have a 2014 Kawasaki Ninja 1000 ABS. I'm wanting to change my OEM brake lines to stainless steel braided brake lines. Do you have any videos on this subject? Awesome video of the valve clearance, spark plug change and coolant change.
@marks4058
Жыл бұрын
No videos on that sorry. But, if you are experiencing poor braking power that's a good place to start. Some other things to consider are: vacuum bleeding the brake system with a syringe or vacuum bleeder (the Z's can be hard to bleed if your brake fluid is thin). Sometimes you think the job is done but there's actually quite a bit of air hiding in there. You can also try more aggressive brake pads and stainless steel rotors. Those will pull you up hard but can be quite grabby. I've done that mod before but not everyone will recommend it.
@igorochakovski3124
4 жыл бұрын
Great video, thanks! Need your opinion: I opened my valve cover and 2 intake valves are 0.25mm (limits: 0.15-0.24) and 3 exh. are 0.33mm (limits: 0.22- 0.31). Would you change shims or not?
@marks4058
4 жыл бұрын
Yes I would change them. The clearance will keep changing over time and any that are out of spec now may continue getting worse. Since these are loose (not tight) it's safe to use the engine until you can get the shims you need.
@enriquemc
4 жыл бұрын
In my opinion 0.01 and 0.02 mm are in the experimental error of measurement. And measuring at +10C is not the same that measuring at +40C (in both cases "room temperature" depending on the place). Don't touch it. The valve cleareance is just to avoid that the valves remain open when the engine is hot. That won't be your case.
@unclebob5686
3 жыл бұрын
@@marks4058 valve clearances (shims) will tighten over time, not loosen. It's better to have a loose clearance rather than a tight one.
@beatsmarttie5777
4 ай бұрын
very good video mark. Did you replace the cover gasket?
@marks4058
4 ай бұрын
Not that time as the gasket was in very good condition. Although I did replace it on the next clearance check.
@vv6816
Жыл бұрын
nice video do u have specs for how to do valve clearance on bmw s 1000 XR ?
@viliusjonaitis3264
2 жыл бұрын
Hello Mark where did you get manual from ?
@kevinansell9341
4 жыл бұрын
Never removed the Camshaft sprockets when doing the Shim replacement on a Z1000SX in fact I leave the Camshafts in I just roll one at a time over to the other side as there's enough slack in the chain when the Tensioner's removed.
@marks4058
4 жыл бұрын
Didn't show it in the video but I also measured the dimensional tolerances + runout on the cam shafts. Was easier without the sprockets.
@BrandonLund
4 жыл бұрын
Nice work but WOW that's a ton of work. I just bought a 2015 with 8k so hopefully I won't be doing this for a while.
@marks4058
4 жыл бұрын
Yeah it's not a simple job!
@BrandonLund
4 жыл бұрын
@@marks4058 as I watched your video I thought to myself...I'll probably just sell it when it gets to that point lol. I cant get over how involved it was. I just did the valves on my Suzuki and I considered it a fairly complicated job. After watching your video, it was about 5% of what you did. Nice work man!
@mot-trance
9 ай бұрын
Top !!! I will be happy if i got this easy like you... I have 20.000km time for exercises on my z900. But i see a problem for the torque values... :/
@user-bt1qj9od6h
4 жыл бұрын
what thread lock did you used for cam cogwheels? thanks
@mrpickles536
3 жыл бұрын
242
@user-ps9vr8ep8g
2 ай бұрын
hi Mark, tell me if I need to replace the timing chain, do I need to unscrew the crankshaft sprocket with the marks?
@marks4058
2 ай бұрын
Kawasaki say that the crank case must be split to make space to remove the timing chain. The sprocket is not removed. Other people recommend splitting the chain and pulling a new chain through with the old chain then joining it. I have not replaced a timing chain on a Z1000 so I can't offer much advice, except to avoid replacing the chain until there is actually a problem like poor timing alignment.
@buana345
4 жыл бұрын
Did you replace spark plug gasket and/or put some sealant on it?
@marks4058
4 жыл бұрын
No, I reused the original gaskets as they were in excellent condition. I only applied sealant in the locations specified in the service manual (the cam shafts cut-outs).
@manorlh3436
2 жыл бұрын
Hi , what is the shim size should I order? for z1000sx? 14
@Pdus64
3 жыл бұрын
I only leave a like on a quality content. This is one of them. That camera angle showing all the process was amazing for a timelapse disassembly. Need to add a music though because that background music sounds like an average lifehacks tutorial music
@marks4058
3 жыл бұрын
Thanks! I was feeling a bit lazy to do high production values on this. It was a 12 hour job and the main thing is that I documented it for others. Wish I had a nice library of stock music I could reach for without having to spend a day searching for it.
@Pdus64
3 жыл бұрын
@@marks4058 ah yes, the struggle of a content creator was to find appropriate music to suit the video itself. Can't blame that one. I also was ambitious making a timelapse to do the job but ended up scrap the idea and do the valve adjustment without recording because of how time consuming it is and inconvenient to move around the tripod without having oil at everything I touch. I respect that courage to produce it despite the extra time to move around the tripod for better shot. I've seen you mentioned 12 hours of job did you done everything in just a single day or combine them from separate days?
@marks4058
3 жыл бұрын
@@Pdus64 I did most of it in one day and just put the bike back together on the second day. I think filming added 2 hours work. Wearing gloves helped and I just left the cameras rolling. Shoot first, edit later!
@Pdus64
3 жыл бұрын
@@marks4058 ah right, i remember i dont have gloves ready when i take it off. welp, at least my motorcycle valve adjustment can be done later. i can use this video as a reference which is better than nothing.
@charliecallcut2219
5 жыл бұрын
Bloody hell! Long ago I did the tappits on my old CX500 but never did buckets and shims. A mate told me decades ago that tappits are easier (no shit!) but buckets and shims stay within tolerances for much longer. Also, big engine in a tight frame. Transverse V engines FTW...
@marks4058
5 жыл бұрын
Yeah, must be very easy on a boxer engine. As far as I know, this one had never been done so I'm not surprised it needed some adjustments after 70,000km.
@SunnieSnell
4 жыл бұрын
@@marks4058 lookin to do mine THanks A lot to do
@marks4058
4 жыл бұрын
@@SunnieSnell Good luck, I hope it goes smoothly. Don't forget to clean any dirt and stones off the frame and around the cam shaft cover before you remove it.
@SunnieSnell
4 жыл бұрын
@@marks4058Hey mate can you tell me the diameter of the shim 7.5mm is what i hear and what range do you suggest for set box purchase Or do i consult the manual which is on 2-26 Periodic maintenance for sizing I have 2 bikes to do 93 z1100 as well as the z1000 2012 Ta in advance
@marks4058
4 жыл бұрын
@@SunnieSnell All my shims measure 7.48mm diameter (basically 7.5). 3.2mm to 2.8mm thickness seems to be the most common but you can occasionally run into adjustments outside that range. You might find a mechanic willing to exchange shims if you need 1 of something. With the older bike I would compare service manuals to be sure they use the same diameter and thickness.
@nicolatesla5342
2 жыл бұрын
Hello Mark, couple of questions: Would you insert a shim if you measured something around near the limit? Let's say low end is at .15 and you measured around .147 etc (using unreal numbers). Or another way of saying it's in the range of spec according to the chart but almost out of range. Secondly, would it be okay to add a smaller shim to increase gap as long as in range? Meaning going off the chart but staying in the range according to the chart
@marks4058
2 жыл бұрын
I think it's important to understand the change over time. If you know the engine and the clearances are stable, with out change between services, then perhaps I wouldn't swap the shim. If the rate of change is unknown then personally, I would change it. Particularly for an exhaust valve, which will almost always get tighter over time. It's also useful to understand what your measurement uncertainty is. If your gauges go in steps of 0.05 then your uncertainty is at least 0.05, probably 0.07.
@marks4058
2 жыл бұрын
Re a smaller shim: Yes any shim that gets you within the specified tolerate is fine.
@nicolatesla5342
2 жыл бұрын
@@marks4058 thank you friend. Excellent video!
@nicolatesla5342
2 жыл бұрын
Do the in and ex sprockets always line up at mark 1.4 for? They never line upfor me at 2.3 hope I didn't f nothing up 🤣
@nicolatesla5342
2 жыл бұрын
Does that 2.3 mark serve a purpose in this scenario on the rotor? My sprockets like up fine at 1.4 for in----ex and in-ex but never on 2.3
@puremad1
3 жыл бұрын
Its More work to get to the place than to do the job of clearance check.... wow...Some places I think needed slowing down alot of important info went past to fast. I didnt realise you had to lift cams out on the engine and thought the lifter would slide across like some kawas do.. BUT nice to know its floating cams and No timing issues to worry about.. Thanks for the video insight on the job... out of interest what's the Milage recommendation for the clearance check on these..35k or so ??
@marks4058
2 жыл бұрын
Bit slow on the reply here sorry. Kawasaki recommend 24,000km for clearance checks. I definitely wouldn't leave it for 50,000km.
@sfzx54
Жыл бұрын
would have loved to see this at about 1/2 that speed!
@cesartapia610
Жыл бұрын
Lol. Even at 0.25x speed, he is going very fast!
@sfzx54
Жыл бұрын
@@cesartapia610 AGREED WHOLEHEARTEDLY!
@MarcelMiranda67
2 жыл бұрын
Do you happen to have a PDF copy of that Valve Worksheet? Looks much nicer than what I am currently using.
@marks4058
2 жыл бұрын
Here you go: drive.google.com/folderview?id=1ZpIwUheYB4O6IiKUMoKNwjVfYGvHscvn
@MarcelMiranda67
2 жыл бұрын
@@marks4058 Just requested access
@marks4058
2 жыл бұрын
I've made it public now. Forgot about that.
@MarcelMiranda67
2 жыл бұрын
@@marks4058 Thanks! This is much better than my current one. Much appreciated!
@beatsmarttie5777
4 ай бұрын
Hello mark. I just measured the clearance of all the valves of my z800. Some are at the minimum of the specification (for example exhaust : 0,22-0,31 I have two at 0,22 mm). I have seen that you had that too and left it as it is. What is your advise? Would it not be better to change the shims to get it in between?
@marks4058
4 ай бұрын
That's a tricky call when it's right on the edge of the acceptable range. Consider what your margin of error might be on the measurements, such as the size steps of the feeler guages. Eg 0.22 could be 0.21 or 0.23 if your guages go up in increments of 0.03, or if it was a particularly hot day when you measured. Another perspective is: You have it open anyway, if you have the shims you need on hand, might as well get it perfect while you are in there. Exhaust ports tend to get tighter over time so that's an argument for doing them now.
@marks4058
4 ай бұрын
It has been a long time since I made this video so I can't recall which shim set I was using. It's possible I might not have had a suitable shim to get closer to the middle of the tolerance range.
@beatsmarttie5777
4 ай бұрын
@@marks4058 al right. Do you use oem shims or is there an aftermarket brand which u recommend? I appreciate the feedback 👍🏻
@marks4058
4 ай бұрын
@@beatsmarttie5777 I don't have a favorite brand but it's always nice to find a kit with laser engraved sizes on them.
@PatoFack
Жыл бұрын
Amazing job you've done. Know what is the diameter of the shims?
@marks4058
Жыл бұрын
The shims I use are 7.47mm diameter.
@dbz1234dkzx
Жыл бұрын
7.47 or 7.48?
@delasse3178
9 ай бұрын
Hi, great video, I've already watched it several times. I've been looking for an answer on whether my bike sounds off because the valves need to be done or not, but all I can find is people saying they got their bike back/back together and POST-valvejob it doesn't sound good. Over the last year or year and a half my bike has increasingly sounded hollow and just grumpy. 2012 Ninja 1000, 19.5K, has sounded grumpy since probably 15k. When I first recognized noise/running issues(certain small RPM ranges -- at speed with low throttle, or taking off from a stop). I replaced the plugs and it sounded significantly different but still weird -- honestly, probably worse. I replaced the air filter with a k+n and that had no change. I ran fuel cleaner through it and it sounded a bit better, and I haven't experienced much for 'running issues' with it since. I also took apart my fuel pump and cleaned out my fuel filter quite a bit, and that had no real impact either. At a bit of a loss, didn't really think I'd have to worry about the valves quite yet but I have lived in the city, so my miles involve traffic. Just wondering if you have any thoughts on that? should i be paranoid I might be damaging my bike? thanks for posting the vid!
@marks4058
9 ай бұрын
Valve clearance should be done at the specified interval on this bike. Don't skip it or put it off, particularly the first clearance check, which is almost due (24k}. It's very unlikely you will hear any major change in sound. Valves just make a quiet click/tapping sound (good) If the sound goes away you have major trouble. A grumbling sound at lower RPM can be caused by a worn front sprocket and/or chain. It may sound like it's coming from the opposite side of the bike too, which can be confusing. The exhaust system will accumulate soot over time which will change the tone and volume of the exhaust sound. That is a gradual change you will experience. Also, check you are running the correct fuel octane number (RON) that the bike is tuned for. Don't go higher or lower, just use what the manual says. I have heard that people use hotter than standard spark plugs in these to help with low RPM running. Sounds like you should get an opinion from a qualified mechanic in person. I can't hear your bike so it all just guesswork.
@delasse3178
9 ай бұрын
@@marks4058 Appreciate the comments. I've read of normally being no necessary changes on most N1K's at the 15-16k mark, typically. Also to "skip the first check" or that "normally the valves dont need any adjustment before 2-3x the stated service interval". So, the sound is specifically with it running, not just in gear. I'm usually running 93, but here in the US even 87 octane I believe is rated at 89-90. I pretty much always run 93. Interesting thought about the exhaust system.. could be on to something there. And/or, honestly lack of any valve chatter. I am posting a video now, no worries if you are too busy to check it out but I would be curious to hear what you thought. Having done the air filter, plugs, fuel filter, run Techron thru it twice, and only being at 19.5K, I'm at a bit of a loss for sure.
@marks4058
9 ай бұрын
@@delasse3178 Skipping clearance checks is something you could consider when you have some data from past checks to show if this particular engine is subject to much clearance creep. Some engines are remarkably stable and others are not. I did the clearance on a Daytona 675 at 90,000km and it needed no adjustment. I've always found at least one valve needing a shim change on the Z1000. Your octane numbers in the USA are a concern for me! Can you verify what the bike is tuned for? Usually these require 95RON fuel. If it hasn't been adjusted for lower octane you probably have a pinging problem that will cause engine damage. Do you know if it was sold new from a dealership in USA? Or imported second hand? Try running a tank of fuel with sufficient lead free octane booster to get the RON number to 95. If that makes it run better, you have your answer.
@delasse3178
9 ай бұрын
@@marks4058 thanks again for the response! the manual for my bike states that it needs 90 RON, and US 87 is 89-90 RON, though I almost always run 93. I will try to boost the octane and see if that makes a difference, but the times I have run some 87 I have not noticed any noteable differences in running quality. The only thing I haven't mentioned is I noticed a minimal amount of water inside my tank lid and was perplexed, and then went to fill up one day after a rainstorm, and water was literally on the lip of the tank opening -- like 360 degrees of water around it. Ounces of it. I dried it up with paper towels and now have a rubber mat over my gas tank so that water can't get in, as I store it with a cover. Water has definitely gotten into the tank and mixed with gas, as for how much I do not know, because I don't really know how long it was happening. I bought the bike in 2020 with 6.5k miles and it was garaged until almost 2022. From my understanding, the problem would mostly be rust in stuff like the injectors, and not engine damage. I do feel like the injectors have quieted as well, unless I'm misassociating noise.
@marks4058
9 ай бұрын
@@delasse3178 Good to know the bike has been adjusted for lower octane. Sounds like the filler cap drain hose is blocked. There should be a drain hole in the gutter around the tank cap which drains through a hose which exits next to the front sprocket. It might be pinched, miss-routed or blocked with dirt. If you are not running E10 or some other fuel with ethanol already, you can put a couple of teaspoons of methylated spirits into each tank of fuel. That will help disperse any water which is accumulating at the bottom of the tank. Water pooling there would cause rough running, particularly at the start of a ride.
@sweatmachine69
3 жыл бұрын
Hi, Versys 1000 owner here. Great video. Thanks so much for making and sharing this. I need to do my valves soon and this will come in handy. Question for ya: Did you modify your airbox? Looks like you have 4x tall velocity stacks. I'm not sure how the Ninja 1000 comes stock but the Versys has 2x tall and 2x short stacks. I changed to all tall stacks and it gave a noticeable low to midrange power & throttle response boost. Did you also drill the plate beneath the air filter? If so, what is the effect of that mod? Thanks again!
@marks4058
3 жыл бұрын
Thanks! My air box is completely stock, those are the original factory stacks. I'm no sure what they did specifically for torque on this bike but it certainly has plenty of low end grunt.
@sweatmachine69
3 жыл бұрын
@@marks4058 Ah ok. I bought a used Z1000 airbox off ebay to rob the stacks from and it came with 2 tall and 2 short stacks. I took the 2 tall ones and put in them in my Versys in place of 2 of my short ones. Did you purchase your bike new?
@marks4058
3 жыл бұрын
Kawasaki changed the air box design for models after ZR1000GCF (2012). Those had two different sets of stacks. Later models like this ZR1000MGF (2014) use the same part for all the stacks.
@mathiaspla8828
Жыл бұрын
@@marks4058 Would the 2012 or 2014 model be better?
@CronoCueva
4 жыл бұрын
great video!, but please take care of the sound next time
@wonderwheels5332
Жыл бұрын
Sir how much cost for z900 shim adjustment?
@marks4058
Жыл бұрын
For a careful job with attention to detail, 6 to 8 hours + cost of gasket and valve shims. Total cost depends on price of labor in your location. In my country a mechanic charges $90 to $120 per hour.
@Pytte
Жыл бұрын
looking at this makes my wallet hurt when I know I need this done on next service :P
@avogel93yj
4 жыл бұрын
At How many miles would this be recommend? Miles or kilometers.
@marks4058
4 жыл бұрын
Kawasaki recommend doing this every 24,000 km or 15,000 miles. However, people frequently leave it much longer. This particular bike had not been checked for at least 50,000km.
@happypanda8320
2 жыл бұрын
Thanks a lot bro. It looks very similar to a z900 which I have. I have 42K miles on it... and seems like a lot of work to even change the plugs which I did. I'm about to do this intimidating task... possibly in dec 2022. Do you think I have some more miles I can put on? I have not noticed anything wrong with the bike. Do you have a printout for that sheet you're using? Thank you
@marks4058
2 жыл бұрын
Here's my worksheet: drive.google.com/drive/mobile/folders/1ZpIwUheYB4O6IiKUMoKNwjVfYGvHscvn Remember the clearance values might be different for the Z900. Best to get the workshop service manual for your bike and check. At 42k miles, I reckon valve a clearance check is pretty urgent. Not all bikes will have a problem but if it has never been done from new, it's likely at least one shim needs to be changed. The Z1000 in this video was at 39,000 miles /69,000km and had quite a few valves out of spec.
@happypanda8320
2 жыл бұрын
@@marks4058 Great man. Thank you so much!
@happypanda8320
2 жыл бұрын
@@marks4058 So I opened up my engine... all of my exhaust shims were out of spec. Yikes. And now I can't find a shim kit online for my z900 smh
@marks4058
2 жыл бұрын
@@happypanda8320 8 valves is a lot to have out of spec. It might pay to get a second opinion from someone who is accustomed to using feeler gauges. It's easy to misinterpret if you a not used to the "feel". Be sure that the engine was cold when you took the measurements (20C/70F ideal). Where did you get your information on the correct clearances from?
@marks4058
2 жыл бұрын
@@happypanda8320 Two more questions: 1) Were the exhaust valves clearances higher than the spec or lower than the spec? If all are higher, it suggests a measurement error. Exhaust usually goes out of spec low. 2) Did you put a sharp bend in your feeler gauges about half an inch from the tip? It's nessesary to have the gauge lay flat on the shim-bucket when checking.
@upperdarbyriders
2 жыл бұрын
Sometime things look easy but they are hard,this looked hard,imagine how hard will it be to do.
@happypanda8320
2 жыл бұрын
I used to work on diesel engines. The hard part was getting to this point to do the actual work, meaning the valves. Haven't done a bike before, but I will do my z900 in the winter... looks like a lot of work to get to the engine
@Mech.E
Жыл бұрын
@@happypanda8320 how did it go? 🤔
@Mech.E
Жыл бұрын
@@happypanda8320 I see you did fine, Nice! This one will be left for the kawa specialist. I have a tendency to break things :)
@delasse3178
9 ай бұрын
@@happypanda8320 ugh getting to the engine is not the hard part IMO. if this is something i need to do with my bike (19.5k) my headache is the internal stuff.
@perciousc9145
2 ай бұрын
I did mine on a concours 14, never again. If I'm keeping the bike for that long I will pay a proper mechanic to do it for me.
@Hussaiin1
2 жыл бұрын
Was that ABRO Grey 999 sealant at 11:04?
@marks4058
2 жыл бұрын
Yes, if memory serves me correctly it was. That sealant performed well in this application and was easy to remove when I serviced this bike 30,000km later.
@Hussaiin1
2 жыл бұрын
@@marks4058 Good, thanks for the reply
@user-or5oo7ce6v
9 ай бұрын
这是锻造凸轮轴吗?
@marks4058
9 ай бұрын
凸轮轴似乎是铸造后进行铣削加工的,而不是锻造的
@_ebj_
2 жыл бұрын
Whete you from ? You have shop ?
@marks4058
2 жыл бұрын
I'm in Wellington, New Zealand. I only do private work.
@oppai1568
4 жыл бұрын
What the spark plug type for z1000?
@marks4058
4 жыл бұрын
NGK CR9EIA-9
@oppai1568
4 жыл бұрын
@@marks4058 This is genuine like from factory?
@marks4058
4 жыл бұрын
Yes, that is the plug listed in the service manual. They last at least 60,000km and only need to be changed if they are out of spec (enlarged spark gap, not firing, damaged or eroded).
@oppai1568
4 жыл бұрын
@@marks4058 Oke thanks bro
@TC-ou8so
4 жыл бұрын
This makes paying someone else $900 almost worth it. What happened to UJMs being the “set it and forget it” of the bike world?
@marks4058
4 жыл бұрын
It does feel like there should be a better way at times!
@proutproutcamenbert
2 ай бұрын
Would you say this procedure can be done by someone who does maintenance by himself, and have some background in mechanical knowledge?
@marks4058
2 ай бұрын
Yes, but you must be patient, methodical and have good instructions to follow (eg the service manual). It's a long job on this bike. Allow 12 work hours the first time. You need to understand how the cam chain tensioner works, correct use of a torque wrench and what the "feel" is like with feeler guages. Ideal if you can have someone else show you what a "go" and a "no-go" should feel like. Take all your measurements three times and do them again if you have doubts.
@proutproutcamenbert
2 ай бұрын
Thanks :)
@proutproutcamenbert
2 ай бұрын
@@marks4058I read that it is best to adjust the clearance to the higher tolerance, because it generally gets tighter, do you agree, or simply refer to the table in the service manual ?
@marks4058
2 ай бұрын
@@proutproutcamenbert In practice, you will often find you are limited by both the availability of shims in small increments and your ability to measure the clearance (eg the increment of the feeler guages). So often there will only be one shim available that you can confidently say falls inside the specified range. If you do find yourself with a choice of two shims that are compatible, then yes I would choose the one that gives more clearance, particularly if you are not going to stick to the manufacturers maintenance schedule. However, don't over think it! If it's in spec, then it's in spec.
@proutproutcamenbert
2 ай бұрын
@@marks4058 Thanks ! So what you are saying is that for example if the exhaust clearance is 0.22 ( the minimum spec ) then you would not add 0.05 to be on the safe side for the next 40k ?
@Peter-un8no
3 жыл бұрын
After seeing this, I think I stick with my Honda CBF1000 and NC750X.
@happypanda8320
2 жыл бұрын
Easier to work on?
@Wann-ez4wl
3 жыл бұрын
Am i glad a retired...as my retirement gift...bought myself a Ducati Monster...🤣🤣🤣
@spoonman73
2 жыл бұрын
Haha your emojis made me lol..
@billmartin126
2 жыл бұрын
I think I will ride my Harley sportster more and Kawasaki Z900RS cafe less.
@armandblake
11 ай бұрын
I think I’ll leave this for the pro and just pay
@fallenwout
4 жыл бұрын
If you pay a mechanic to do this, it looks like it is cheaper to buy a new one.
@marks4058
4 жыл бұрын
It's definitely an expensive job. Probably around 8 hours work in total.
@johnmayberry7669
4 жыл бұрын
Whats the point of doing a cracking video then showing it at 200mph🤔🤔🤔🤔
@marks4058
4 жыл бұрын
It's an artistic counterpoint to all the long, drawn out, heavily narrated KZitem mechanical videos where you could go make a coffee then take a stroll around the block and not miss a thing. Also, I watch too much Jimmy Diresta.
@nuclearchris832
4 жыл бұрын
Mark S thanks for this. I will give it ago because of your video. Also I want to acknowledge all the good camera work so I can see what’s going on
Пікірлер: 163