Fantastic!!! This is way better than just taking a pot shot at cutting and welding a diff together. I have to get my lathe up and running.
@fausmartinez6342
Жыл бұрын
En mi país un usado te lo venden como si fuera nuevo, ay lugares donde estan al abandono. Exelente trabajo.
@abdulmuis6991
Жыл бұрын
Mantap hadir nyimak kawan dan jangan lupa mampir ngopi kawan sukses selalu buat sobat 🙏🤲
@mihkus
Жыл бұрын
Belive me, solid axle cralwer-like ATV would be the coolest thing anyone could ever build.
@inovativobsesion2796
Жыл бұрын
Just go buy an old Honda atv
@ianbuilds7712
Жыл бұрын
@@inovativobsesion2796 so innovative**
@ianbuilds7712
Жыл бұрын
@@inovativobsesion2796 you do understand that building stuff is half the fun right?? I mean an old atv is a good restore project but I think you're missing the point
@user-xg1jg5zu6q
Жыл бұрын
Имея токарный станок, соосность чулков выставили по параллельности палок! Не могли что ли центрующие фланцы выточить на чулках и приварить потом идеально, нежели на глазок херачить?
@ukrainka-4523
Жыл бұрын
московитьське чмо не суй свій довгий ніс люди роблять як можуть а такі гандони як ваша недонація може тільки лапті плести та на чужі держави нападать
@thisisyourcaptainspeaking2259
Жыл бұрын
I always wondered where those Polaris differentials are sourced from! ;)
@fggsxvj7516
Жыл бұрын
Привет! Отличная работа 👍 Но этот вариант не рабочий,при нагрузке сломаются полуоси.
@jakelong781
5 ай бұрын
What vehicle did that axle originally come out of? Great job by the way!
@makeandride
5 ай бұрын
Daihatsu Hijet mini lorry
@ferozakig
Жыл бұрын
Greetings from California , been following you also your other channel, RofE. Keep up the good project..
@dk832002
Жыл бұрын
Why an offset axle for an atv? And y no locker?
@user-kb3zf3rj1b
Жыл бұрын
Super filmik 🎉, like 👍💪
@modification_king_official
Жыл бұрын
Good work
@jessemoss2548
Жыл бұрын
Been dreaming of building this for 20 yrs. Now that I'm old,tired,wore out and retired , I might get started on my 88f-250 4x4 scale down.
@DatBoiOrly
Жыл бұрын
ngl i thought this was going to be one of those videos where he just does a poor job like those "restoration" channels but god damn i'm honestly impressed he did everything by the book from facing off the two halves with the lathe to make sure they mated true and parallel, then drilling out one side and making the shaft end a press fit to minimise warping then using the lathe to chamfer the weld surfaces to get penetration all the way through whist using the lathe as a clamp to again minimise warping. my only 2 complaints are: -that the shaft wasn't heat treated/normalised but the amount of power an ATV produces i don't think it'll be needed since they're over built for the application -finally the mounting brackets are a bit too thin for my liking but again the amount of power the engine will produce/ the weight of the ATV i think they'll do overall a really good video!
@SolitaryCanid
9 ай бұрын
What is the differential out of?
@neniys1142
Жыл бұрын
Tipz nya sangat bagus 💅
@frias2287
Жыл бұрын
Nice🔥🔥🔥
@Miniscapes515
Жыл бұрын
I like how they never measure or square things up in these types of channels
@haroldbarrows8483
Жыл бұрын
Not to mention no heat treat on the axles after welding lol
@SamsungJ-bi8jp
Жыл бұрын
Hola por fabor si usted me podria vender dos yo se los compro me los podria emviar en un courier yo vivo en Ecuador me avisa cuanto valen los dos
Пікірлер: 43