i have exact same boiler, but i don't know how to re-pressure it because it doesn't have this loop :( both right tubes go inside the boiler and are not interconnected
@niccilou580
2 жыл бұрын
This is my boiler but it doesn't look the same underneath so I can't see how to get the pressure up. Any thoughts? It won't let me send picture.. But I have the first and fifth leading to what looks like water and the third is labelled gas.. The 2nd and 4th pipes under neath are capped and don't lead anywhere... Thx for your help. Pressure 0. No service til November.
@BB-xh3ik
2 жыл бұрын
Salut steve ma chaudiere monte en pressiom jusque 3,5 bars et elle fuit du a ca as tu une solution merci ?
@catalinaga
2 жыл бұрын
I've got the same model and slightly different piping but the point is, the left valve can be turned, while the right is stuck
@catalinaga
2 жыл бұрын
update: had someone come to unstick it with a wrench, and it worked. thanks for the vid
@sylvierochereau1439
Жыл бұрын
Comment remettre pression sur vitodens 100, je n ai pas de manette noire
@Matruchus
11 ай бұрын
This is the version of the boiler that is used with a water tank. Repressuring the one with flow through sanitary water system is not possible like this.
@nezreendent1343
3 жыл бұрын
Do you have to turn the boiler off before adding cold water.
@stevetilsley354
3 жыл бұрын
Hi Nezreen. Just leave the boiler running. All you are doing is adding a little water to get the pressure back up. Don't add too much.
@nizaral-jomailee5180
3 жыл бұрын
Hello sir, I do not have these pressure keys. With knowledge of the same quality, it has only one small key and when I turn it around, the pressure does not increase, but rather it decreases. I need to raise the pressure.
@stevetilsley354
3 жыл бұрын
Steve Tilsley Hi. I'm not a heating engineer or know anything other that experience with my own boiler. All i know is to check your outside vent isn't blocked and how to reset the water pressure gauge as the heating will pack up if the pressure too low. If there is not these two taps on a loop like mine then I have no idea how to increase the pressure.
@nizaral-jomailee5180
3 жыл бұрын
@@stevetilsley354 thank you su mach mister steve
@nezreendent1343
3 жыл бұрын
Read that you should turn boiler off before adding cold water. Is that correct.
@harismeher1467
3 жыл бұрын
Hi steve I was wondering if you could go over the confi mode settings. My central heating won't come on
@stevetilsley354
3 жыл бұрын
Hi. Im not a heating engineer or know anything other that experience with my own boiler. All i know is to check your outside vent isnt blocked and how to reset the water pressure gague as the heating will pack up if the pressure too low.
@florinistina95
Жыл бұрын
Vă rog ambient
@christineboghossian8488
3 жыл бұрын
J'ai qu'une vanne jaune et une vanne noir et ça me marque F4 clignotant
@constantinsarafian5942
3 жыл бұрын
Codes erreur Chaudière VITODENS VT100W -------------------------------------- 10 Sonde de température extérieure en court-circuit. 18 Sonde de température extérieure défectueuse ou mal branchée 30 Sonde de température chaudière en court-circuit. 38 Sonde de température chaudière défectueuse ou mal branchée. 50 Sonde de température ECS en court-circuit. 51 Sonde de température de sortie en court-circuit. 52 Sonde de débit en court-circuit 58 Sonde de température ECS défectueuse ou mal branchée. 59 Sonde de température de sortie défectueuse ou mal branchée. 5A Sonde de débit défectueuse ou mal branchée. A9 Problème de communication avec l'appareil Open Therm. b0 Sonde de température des fumées en court-circuit. b8 Sonde de température des fumées défectueuse ou mal branchée. E3 Problème au niveau de la chaîne de sécurité. E5 Problème interne résultant d'un blocage du brûleur. F0 Problème interne résultant d'un blocage du brûleur. F1 Surchauffe des fumées d'évacuation. F2 Le limiteur de température de sécurité a réagi. F3 Le signal de la flamme est déjà positif lors du démarrage du brûleur. ** F4 Aucun signal de la flamme. ** F8 La vanne de combustible met trop de temps à se refermer. F9 Vitesse de la turbine trop faible lors du démarrage du brûleur. FA La turbine ne s'éteint pas. FC Commande de la turbine de régulation défaillante. Fd Boîtier de contrôle du brûleur défectueux. FF Boîtier de contrôle du brûleur défectueux.
Пікірлер: 18