This is an awesome tutorial! I am not really good at fixing cars, but with this video I made my heating work well again. Thanks a million for putting this together 😁✌️
@Vicks-141
3 ай бұрын
Thank you did mine today, my heater was blown. Might be summer but can still get cold at night ❄️
@blackie_swart
8 ай бұрын
Thank you so much. I'm having the same problem, and appreciate the manner in which you explained, while working. 👍
@luketaylor684
7 ай бұрын
Great write-up- thanks!
@slapico
Жыл бұрын
Very helpfull ! I have the same problem on my vito. Thank you very much 🙏🏻
@fixitfallows
Жыл бұрын
I would recommend changing the cabin filter at the same time, as it could be very dirty which is what can cause the excessive load on the resistor pack. As the load builds, the current draw heats up the cabling which in turn blows the thermal fuse in the pack..... there is a chance you'll just blow the new pack in a short time if the filter isn't replaced....... which is what happened to me 🤦🏼♂️
@petrturcovsky7035
7 ай бұрын
Excellent! Thank you very much.
@butkusje
6 ай бұрын
prachtig super uitgelegd
@fixitfallows
6 ай бұрын
je bent erg aardig
@cankesk2415
9 ай бұрын
How about the rear passenger side . My one is heating my side, but the passenger side blowing cold air
@djru1881
Жыл бұрын
Do you have an idea how i can easylier to take off the black plastic to put off the blower? In your video it looks very easy, but it isn't 😢
@adamdobias4052
Жыл бұрын
Thanks for the video, I have exactly the same problem! Does anyone know exact sizes of the torx heads needed for this job? Thanks!
@AbdulAlim-lq4sk
3 ай бұрын
Hi , thank you for a very informative video. Would this fault cause cold air not blow out? I have just topped up my ac gas and it’s not getting ice cold . My fan only works on 5 .
@fixitfallows
3 ай бұрын
If the fan only works on "5" I'm pretty sure that your resistor pack has blown. It's very likely that your AC compressor clutch is linked to this too (I'm not 100% sure on that though, but seems logical).
@AbdulAlim-lq4sk
3 ай бұрын
thanks for your reply , I will try changing the resistor pack.
@mariuszziarnik2042
Ай бұрын
Thanks for helps
@leechadwick2955
Жыл бұрын
Could this also be a cause for the motor not working at all on any setting?
@fixitfallows
Жыл бұрын
Usually when the resistor pack goes you still get full power as the max power setting doesn't go through the resistor pack. Check that you have 12volts going to the main connector for the blower motor when you have your switch set to maximum. If you do, then it suggests a motor issue (stuck due to seized bearings/bushings or warn/dirty brushes or commutator. If no power, then perhaps its a switch problem. Then also, whilst I haven't checked, there may be a dedicated fuse for the circuit in one of the fuse boxes on the vehicle. I hope this gives you a few options and good luck.
@amitladhani7394
Жыл бұрын
Hey there, I've followed your steps and changed the resistor but it still only works on 5. Any suggestions?
@fixitfallows
Жыл бұрын
There is a chance you may have blown the new resistor pack straight away.... I've since learnt that if your cabin filter is very blocked that is what can cause the pack to blow as it causes such a strain on the wiring, the heat builds up and blows the thermal fuse in the resistor pack. The cabin filter is changed via the plastic access panel between the wind screen and bonnet between your wiper blades.
@amitladhani7394
Жыл бұрын
@@fixitfallows thank you so much. Your video helped me a lot. Especially the tip about putting the rear of the cover in first. That bit too me ages to get back in!
Пікірлер: 24