I was stuck, everything worked except I had no modulation on TX output. As you demonstrated at about 4:00, the "Rear Select" setting was the issue. Once I switched it to "USB" it worked. Thanks!
@nebraskarooster9244
Жыл бұрын
Thanks for this! I had tried the settings from my g90 and they weren't working out - this got me on the air with FT8!
@roystonjones3134
Жыл бұрын
Thanks Steve for the info and guidance, having tried many other bits of advice to enable transmit FT8 on FTDX10 without success. Followed your rig set up and all working fine now. 73 Roy G4SWH
@joediagnostics
8 ай бұрын
Thanks for this. It worked perfectly for me!
@robhawkins2492
Жыл бұрын
Many thanks Steve
@meggalavk3ktt
9 ай бұрын
LOL when the author comes back to his own video to check the settings :)
@adamcar2773
Жыл бұрын
Thanks Steve. Good job. 73' Adam SP4IZK
@bluzman00
2 жыл бұрын
Push the Mode button and press Preset….done. To exit, do the same. No need to make adjustments except TX power.
@audi2000it
8 ай бұрын
tanks and 73 from ITALY. IN3KTT with also Yaesu FTDX10 :-)
@bigdaddyvu
Жыл бұрын
I just the usb cord and works flawlessly without taking over the mic port. It has built-in sound card and ft8 digital modes in the memory.
@ronancullen4565
2 жыл бұрын
Latest firmware has preset mode for ft8, sets all settings for you
@marvs4321
Жыл бұрын
Yes, but this PRESET mode assumes you are going to use the USB port for your data modes. It doesn’t work if you want to use the other ports on the radio. Also note that the USB port has a 16-bit A/D soundcard which is the same as your PC. However, some external data devices (microHAM for example) have 24-bit A/D soundcards.
@mikeh9446
3 ай бұрын
Totally correct on the Microham Keyer 3 for FSK ie use Of FT 8, which uses microham USB Router with software to add as many Ports for use CAT x 2 plus Ports for all different PTT modes. I had to give Ports for Phone, FSK and Foot Switch plus another Port for Headset, and change FTDX10 setting to RTS for FT8 to work, mindful this how Keyer 3 operates.
@SherwoodR631
Жыл бұрын
appreciate the video; i updated the firmware and lost all my settings.
@kg5nub
Жыл бұрын
you'll make a drunk man pass out with the shakeness, im about sick
@ae4xo
11 ай бұрын
We had it working. Got 1 contact and now the Test Cat is still red . And computer doesnt talk to the radio
@meggalavk3ktt
11 ай бұрын
you probably have rfi in your signal try separating your cables from the coax and wind a mix 31 around your usb cable as many time s as possible. lastly check you coax plugs are tightly wound.
@haskellnj
7 ай бұрын
You don't show the cable hookup!
@MikeG-js1jt
Жыл бұрын
why is your vfo in DATA-U as opposed to USB ?
@meggalavk3ktt
Жыл бұрын
that is how i was told to run it i know you can do just usb but i kept this simple in the data u mode.
@marvs4321
Жыл бұрын
If you use DATA-U or DATA-L a 3kHz BPF is used and you can go thru the mic, USB, or rear ACCY port. If you use USB only, you MUST use the MIC port for TX and you can vary the RCV BPF width.
Пікірлер: 23