Vielen Dank Doc 🙂🤝Du weißt ja, ich geb immer alles 😅✌
@ModellbauChecker
6 ай бұрын
Sehr gut gemachtes Video! Schöner Flieger 👍👍
@ThrunRC
6 ай бұрын
Vielen Dank mein Freund 🙂👍 Ich find den Flieger auch sehr gut gelungen👌
@ARGON023
Ай бұрын
BRAVOoo, BRAWOoo DZIĘKUJĘ ZA to NAGRANIE! Pozdrawiam.
@ThrunRC
Ай бұрын
Thank you 😉👍
@Nobody-qp9jm
6 ай бұрын
Sehr schöner Flieger. Mir juckt es auch schon wieder in den Fingern, nach nun 4 Monaten endlich mal wieder zu fliegen.
@ThrunRC
6 ай бұрын
Optisch gefällt er mir auch sehr gut, fliegt sich aber natürlich auch super 🙂👍 Hast Du Winterpause gemacht ? Ich find es immer noch sehr kalt zum fliegen aber ab und zu wenn sich die Sonne zeigt kann ich dann auch nicht anders 😅👍Die ganze Zeit nur Autos fahren find ich auf Dauer auch langweilig.
@Flybrei
6 ай бұрын
So muss nach der Belehrung erstmal Eigenwerbung machen. 😜✌️ Cooles Video und toller Flieger.
@ThrunRC
6 ай бұрын
Eigenwerbung wird umgehend gelöscht 😋 Vielen Dank 🙂🤝
@langer532
6 ай бұрын
Hallo super erklärt 👍 Ich habe mir den Habu STS 70mm EDF Smart Jet RTF with Safe, 1029mm bestellt bin gespannt drauf 😊
@ThrunRC
6 ай бұрын
Danke Dir ! Viel Spaß damit :-)
@tilliewang-vh5fs
6 ай бұрын
Super Video, erklärt gut! Mache weiter🥳💪
@ThrunRC
6 ай бұрын
Viel lieben Dank 😊🙏👍👍
@tantebuggabugga
6 ай бұрын
Klar etwas zusammen stecken geht ja nicht anders bei der Größe. Sah aber jetzt nicht wirklich schwer aus. Aber Tolles Flugzeug sieht richtig gut aus. 👍
@ThrunRC
6 ай бұрын
Der Aufbau ist total einfach, geht ruckzuck 👍 und das Flugzeug fliegt wirklich prima. Zum einsteigen auch sehr gut geeignet, es ist sehr, sehr robust 😅👍👍
@ARGON023
25 күн бұрын
Hello, This wing connector is a brass tube, it should be 32cm. It is shorter. 13cm for the left wing and 13cm for the right, the fuselage is 6cm. I tried to buy it but the diameter of this tube is non-standard, it is 7.9 mm. Standard tubes for RC models are 3,5,6,7,8,9,10 mm in diameter. Best regards.
@ThrunRC
25 күн бұрын
Thanks for the informations. I think you can take a 8mm tube and simply sand a little bit of till it fits. 0.1mm is not much.
@wolfgang7513
3 ай бұрын
Servus Thorsten, danke für das wieder mal tolle Video. Eins hätte ich mir noch gewünscht : Man sieht leider nicht wohin und wie der Empfänger platziert wird. Für alte Hasen sicher uninteressant aber für Einsteiger eine offene Frage. Grüße aus Franken, Wolfgang
@ThrunRC
3 ай бұрын
Servus Wolfgang, danke für dein Feedback. Den Empfänger hab ich durch das Akkufach im Rumpf befestigt. Das ist die einzige Öffnung durch die man in den Rumpf gelangt. Ist etwas fummelig aber ging ganz gut. LG Thorsten
@m.p1976
22 күн бұрын
STARK😊
@ThrunRC
22 күн бұрын
VIelen Dank 🙂
@FernandoLopez-kp2jp
4 ай бұрын
Hi Thrun, do you have any idea at what speed does it usually fly Thank you
@ThrunRC
4 ай бұрын
Hi Fernando, I'm very sorry but I haven't measured the speed yet.
@roadstar499
5 ай бұрын
So a 5000 mah 3s was in that when flying? How much flight time can you achieve? 15 mins? Thanks for sharing. this airframe was well designed imo..
@ThrunRC
5 ай бұрын
I had a 3000mAh 3S Lipo at the first flight. At a moderate flying speed you can easily fly for about 15-20 minutes with a 3000mAh, but of course the flight time depends on how much throttle you give. 😉👍
@roadstar499
5 ай бұрын
I actually have 2 hardly used 4500 mah 60c 3s packs...i wonder if this plane has enough room for them...thanks for sharing
@ThrunRC
5 ай бұрын
@@roadstar499 Hi,sorry for late response. There really isn't much room for batteries in this plane. The maximum height of the batteries should be approx. 3cm otherwise you won't be able to get the lid on. The length and width is not so critical as long as the center of gravity still fits. 👍
@roadstar499
5 ай бұрын
Actually they are small 13cm x 4 cm x 2.5 cm...should fit
@ThrunRC
5 ай бұрын
@@roadstar499 Ok, yes sounds good. I think this should fit. 👍
Пікірлер: 30