Such an underrated video!!! Great job! You mentioned every tool used, propped names for things, proper procedures, etc!! Amazing at home diy on a budget. Much respect.
@ADollarAndAWrench
3 жыл бұрын
Thanks alot man i appreciate it im glad it helped hope it goes smooth for you while ur charging your clutch thanks again
@norriscarey9822
3 жыл бұрын
@@ADollarAndAWrench of course brother!! Such a informational video.
@mrchrisknight315
5 жыл бұрын
Respect. I need to replace my transmission since 5th gear won't stay engaged. I didn't think it could be done from the ground. You just proved me wrong!
@ADollarAndAWrench
5 жыл бұрын
Hey man ur welcome im glad the video helped a little
@tegimr
Жыл бұрын
Wow. I'm impressed, and discouraged. I can't even get the air box off and replaced in 14 minutes and you did the whole thing in 14. Seriously, though, awesome job and details.
@ADollarAndAWrench
Жыл бұрын
😅😅😅😅 thats was funny I wish it took 14min Thank you . Watch it a couple of time and get someone to help u U and a buddy can get this done in a day
@privatehand
5 жыл бұрын
That is so complicated it's almost criminal. Good work.
@scottwhitfield9558
2 жыл бұрын
Best how to I’ve seen
@ADollarAndAWrench
2 жыл бұрын
Thanks man i appreciate that Hopefully everything goes smoothly for you
@mickd8490
5 жыл бұрын
Good video, I like the fact you put in the required tools as well.
@ADollarAndAWrench
5 жыл бұрын
Thank u i hope it helps
@Elldeeve
4 жыл бұрын
8:39, massive hole in flywheel housing! That’s probably worth plating over. Good job though, I’m about to do my mk4 golf tdi. Getting my research in before starting
@ADollarAndAWrench
4 жыл бұрын
LOL yea I noticed .. but this car is long gone good luck with your project it's pretty easy once u get started
@rickblack7649
Жыл бұрын
Ya same here...
@zomiipanda
5 жыл бұрын
Damn bro thank u this is the best clutch reinstall for be out there thank u again!!
@ADollarAndAWrench
5 жыл бұрын
Thank you i hope it helped
@zomiipanda
5 жыл бұрын
A ton Man U made it look easy to do , ur the only one that u can see what ur doing most the other videos are to dark
@soilmanted
4 жыл бұрын
Yes I think you need a second person, for a short time - to help detach the transmission once you have all the fasteners removed, so that it doesn't drop down too fast and damage something, and to help get the transmission back up and into place when you are ready to do that. But you don't need pure muscle power to get the transmission back up, for example. You can have one person aligning the transmission input shaft with the clutch pressure plate, friction disk, and engine gland nut, and the other person lifting the transmission upward. However the person lifting it upward can use a jack to lift it upward. I don't think you would need a nice rolling-around hydraulic jack like you have supporting the engine. Just an old scissor jack should do. Maybe put a piece of plywood on top of it. Also a plain hydraulic jack without wheels should work. No? I'm just guessing; I've never done this before. But I've removed air-cooled engines from air-cooled VW bugs and that's what I did. I think maybe I used just one scissor jack right under the oil drain plug which appeared to be at the center of gravity to gently let the engine down, and gentlly lift it up. When lifting the engine probably I kept piling up pieces of one by four lumber under each of the heat exchange boxes on each side of the engine, so that if the scissor jack wasn't perfectly centered and the engine rocked from side to side, each heat exchange box would never be more than an inch or so above a wooden support block. Jack the engine up another inch, add another inch-thick one by four, jack it up some more, etcetera. I recall using a helper but they didn't have to be strong. They only had to operate the scissor jack while I looked to see if the hole were aligned. I seem to recall eventually figuring out how to do it without a helper but I'm not sure.
@MTLJack
4 жыл бұрын
Or use a jack to support it and lower it
@javaidsadiq5775
5 жыл бұрын
Bloodclaaaat bumba bwoy. Wa de bumbaa! Ti raatid!
@ADollarAndAWrench
5 жыл бұрын
😂😂 what the video didn't work for you
@brettlake2947
4 жыл бұрын
Great job thank you for video.
@ADollarAndAWrench
4 жыл бұрын
Thanks hope it helps
@robs662
3 жыл бұрын
Just the job my man 👌
@curbsidemechanic3229
5 жыл бұрын
Bro, I have a MK4 2.0 that I burned the clutch out on. Its cold as hell where I am right now and I don't want to freeze my ass off. I want to know how long it took you to actually complete this project?
@ADollarAndAWrench
5 жыл бұрын
Before you start make sure you have All the tools you parts and tools you need. Your going to need help pulling the transmission off and pulling it back in. Should take you 3 days
@cun7sathome
4 жыл бұрын
3days!!!!!! It 8 hours on the floor at most
@yungoldhead5600
5 жыл бұрын
Respect brudda!
@LoniVlogZ
3 жыл бұрын
A real clutch job my turn to do one lol
@ADollarAndAWrench
3 жыл бұрын
Get it done brother lets go
@rickblack7649
Жыл бұрын
Same hear
@yungoldhead215
5 жыл бұрын
Did u remove the axle on both sides?
@ADollarAndAWrench
5 жыл бұрын
Yes
@yungoldhead215
3 жыл бұрын
Freddie Villa yes
@yungoldhead215
3 жыл бұрын
They’re both connected to the transmission.. it wasn’t hard at all
@lauralynnepariset2304
2 жыл бұрын
How long did this take u to do??
@ADollarAndAWrench
2 жыл бұрын
Without filming Shopping to go buy tools i didn't have You can get it done in 6 to 8 hours On the ground
@tylerfritzinger6619
2 жыл бұрын
What’s this for a 1.9L Jetta tdi
@ADollarAndAWrench
2 жыл бұрын
No a 2.0L 5speed
@thomgomez2799
4 жыл бұрын
😀👏
@prolifik_hussle5972
3 жыл бұрын
Definitely 🇯🇲
@ADollarAndAWrench
3 жыл бұрын
Yea man yuh dunkno
@hernes0071
2 жыл бұрын
This is so wierd my cluch dotsent look anything like that
Пікірлер: 45