Thank you Sir for your video. I have just aquestion, how can I give 2volt without having the Autosim as you have in the video, is it eny way to put 2volt as you said in the unit system without Autosim. other question what if I buy new used unit, do I need to program it, or is it just to conect if the part number is the same. Thank you
@TheDerekeder
2 жыл бұрын
The Additive tank has a 4 pin connector. Pin 1 is the tank motor. Pin 2 is both the motor's "ground" as well as the signal ground for the level sensors. Pins 3 and 4 are for 2 separate piezo transducers which measure fluid level. The measurement works like SONAR - a high frequency "ping" is sent out and the time delay to it's echo is related to the fluid level. Measurements are only taken when additive injection takes place and when the car is started. I don't understand how the AutoSim Pro was used in your video and wonder if the faults were resolved solely by refilling the tank.
@nickybazzi4205
Жыл бұрын
Filling the tank doesn't solve the issue because the control unit doesn't recognize the additive level inside the tank.
@majidmajidy5733
2 жыл бұрын
Thank you Sir for your video. I have just a question, how can I give 2volt without having the Autosim as you have in the video, is it eny way to put 2volt as you said in the unit system without Autosim. other question what if I buy new used unit, do I need to program it, or is it just to conect if the part number is the same. Thank you
@Bbbb-rk3bu
2 жыл бұрын
Dear Sir, thank you very much for your movie. Can you possibly inform me where to connect your Autosim Pro in order to generate the signal. I have the same problem, there is no voltage from the ADM output. Thank you in advance.
@trasession
2 жыл бұрын
Hello thanks for your question. It's been a while since I done this video. I had a look at a wiring diagram and you need to power up the level sensor in the tank from the control module side
@dotsfrazer
Жыл бұрын
How much to you charge for doing this I am in dublin and could get you to do it
@garywallace7132
3 жыл бұрын
hi, not mechanicaly minded, but have same problem. when you sent a signal through wire and you cleared the code, did you still have to replace the module
@zarkaayamamatv7469
3 жыл бұрын
Hello thank you for your video I have volvo c30 with error message "gestion moteur reparation urgent" When i did the diagnostic i have the error "additive dosing module" Could explain me what to do i'm from morocco thanks
@trasession
3 жыл бұрын
Hey it depends on the fault codes as to the direction I would take
@kenzoeddie6972
3 жыл бұрын
I guess it's kinda off topic but does anyone know a good site to stream newly released movies online ?
@mauricedaxton5230
3 жыл бұрын
@Kenzo Eddie Lately I have been using FlixZone. You can find it on google =)
@hayesdayton2043
3 жыл бұрын
@Maurice Daxton yup, have been watching on Flixzone for since april myself :D
@kenzoeddie6972
3 жыл бұрын
@Maurice Daxton thank you, I signed up and it seems to work =) I really appreciate it!
@samppapetteri-bx1kb
2 ай бұрын
There is no point of these kind of videos if you are not telling or showing exactly what is the signal and how you are sending it to unit. Is it just 2 Volts dc and is the brown wire the positive one and the one wire (with yellow stripe) at right up corner of the terminal is the ground wire?? Looking this video only shows that you can do it but it does not give us exact info how we should do it. I don't want to try it with this weak info and burn my module. Give us better info and you will get more followers for your channel.
Пікірлер: 17