OMW.....So after work today, I played with my settings. In the never ending quest to find settings that will make my ebike mimick the feel of a CR 125. Welp, I was on page 3 and decided to enable moving vehicle booster. I tried the stock #10 setting and not much. I then set it to 30. That's all I did, and wrote it. It flies. Moving vehicle booster Speed ratio is all I touched so far. it's got to be the secret setting no ones talking about.
@AdventureBrad
3 ай бұрын
Nice will have to check that out. Thanks for sharing
@derbestebusfahrer.
6 ай бұрын
I have a question . Why after I enter values in the EM-100 controller after pressing the record button, after switching off and on again the controller returns to the old settings.
@TackleThat
5 ай бұрын
Same here, did you ever get it working some how?
@derbestebusfahrer.
5 ай бұрын
@@TackleThat yes, Probelem is with Software.
@TackleThat
5 ай бұрын
@@derbestebusfahrer. How did you get it working? I have the same problem.. tried 2 different EM software versions. What version worked for you? thanks!
@polyteky
Жыл бұрын
Hey, how do we map the port settings with the pin number/color in the connector. Don't understand what PD0,JTCK,SWD etc. mean
@oviboardes663
2 ай бұрын
HI. Thank You for this tutorial. So, i have problem with my EM_150/180A. Any way to connect with software. I thik that firmware is corrupted. Could You send me Your on priv, please?
@racko6ix
4 ай бұрын
Hope my question wis reasonable. Is it absolutely necessary to have the controller hooked up to the computer diagnonis? I got to having it hooked up and finally connecting the learning wires and turning the key to on. No motor turn. My display turns on, but I think it runs from my head light wiring. I haven't tried to turn the throttle yet, but I want to. USB wont be here till tomorrow, it says.
@TroyPlayz
7 ай бұрын
I keep getting a hall fault on my em150sp, the dkd display powers on and starts on mode 3 and it can do sport + reverse but not 2 or 1. As well the motor has still yet to turn, do I need to do the self learning process for the hall or do I need to rewire/reprogram something?
@moritzburn6694
Жыл бұрын
Is there a setting which can limit the top speed of ECO mode to 25 km/h?
@imho7250
10 ай бұрын
Yes, @8:20 (page 2), if you check HDC enable and specify an RPM limit (6000 rpm in this case), then in the Three-speed section, he has 80%, which is 80% of 6000 rpm), for LOW, which is 4800 rpm. For you to set LOW to give 25 kph max, you just adjust the % of LOW until it limits your speed, which depends on motor type and tire diameter. Probably by now you already found someone who helped you set this basic setting.
@WaseemAli-dj2yp
6 ай бұрын
Hello sir plz tell me the difference between em150 and em150sp controller
@mct8888
Жыл бұрын
Where is the auto-learn function?
@decokjr
Жыл бұрын
Great
@javedinfotech1
Ай бұрын
Sir how to do reverse setting
@AdventureBrad
14 күн бұрын
Not sure
@AerialAcesRC13
Жыл бұрын
Would you be willing to help me correctly figure out what pin-out is correct for my Votol Em70 PLEASE? or ANY help in locating the correct data plug!? I have seen "modification groups" and after reaching out, received no response what so ever. I understand time is a rare commodity, and would be willing to compensate... Thank you. PS: I understand this SHOULD be a EASILY answered question. Evidentially Nobody has spent time programming the EM-70 BLDC controller. Ours is specifically re-badged as a "YMMOTORS" variant, and to my attention has a COMPLETELY different pin-out compared to the schematic presented on the VOTOL web site, along with the prints shown in the sales links VIA Amazon. I am very nervous to simply cut into my harness without knowing the correct designations. Bike has been SPECTACULAR, EXCEPT we are limited to GEAR 2---45ish MPH!!! Gear 3, 4, and Sport remain without access. This may sound like a simple issue, and may be, but without correct english translations, and incorrect or limited knowledge, quickly becomes a chore. ANY HELP or DIRECTION would be dearly appreciated, as you seem to be able to navigate electronics IE drones/bike. very well. Keep up the hard work, and thank you for sharing your finding thus far!!!
@AdventureBrad
Жыл бұрын
ask the seller you bought it from. I haven't played with a em70
@AerialAcesRC13
Жыл бұрын
@@AdventureBrad understandable. Unfortunately it was purchased through @flyebikes and did not have a admirable "after purchase" experience, not that I expected much. Been trying all outlets we can find that may have the time or knowledge to assist in this endeavor. Thank you for a quick response, and we still love your detailed content!
@Diygenes
Жыл бұрын
Please explain how to measure Hall Shift Angle with oscilloscope, or at least point to some documentation, please. I can't find any.
@loopy2098
Жыл бұрын
any tips why mine wont connect? it keeps popping up with a error when i connect the controller and i have tried EVERYTHING , contacted the provider and they weren't much help tbh
@AdventureBrad
Жыл бұрын
what is the error? can you see the controller in the serial port?
@AdventureBrad
Жыл бұрын
more then likely its a driver problem. might try a different computer too
@loopy2098
Жыл бұрын
@@AdventureBrad i can see my port , its communication abnormal that is the error i cant seem to shake
@trewatkins530
Жыл бұрын
Mine says when press connect … let’s open the serial port
@AdventureBrad
Жыл бұрын
that means your computer is not seeing the usb adapter. make sure the drivers are installed and updated and pick the right com port
@trewatkins530
Жыл бұрын
@@AdventureBrad now that part i have to figure out the drivers I'm not to computer savy
Пікірлер: 28