Always come back to you when I need help with lightburn. You are the best! Thank you!
@computercreationz
2 ай бұрын
I appreciate the comment
@LowVisionUKTerrysView
3 жыл бұрын
Good evening Robert. This was yet another very informative video tutorial - thank you, as always. I have been looking at line and fill on lightburn, but did not, until your video realise there were separate options for both the line and the fill element - awesome. After all of these months waiting, my laser had finally arrived - today :-) However, it has a cracked sense, so, I should receive a replacement tomorrow of the following day. Im so excited that I can now put what I am learning from you into practice. I will certainly be returning to some of your older videos as reference during my learning my laser phase. Robert - thank you so much, as always, and I hope both yourself and your wife are doing well Terry
@computercreationz
3 жыл бұрын
Hey Terry, thanks for the comments, so glad your laser finally showed up. now the fun starts!
@fredwienbarg5051
2 жыл бұрын
I downloaded the new version but without your video, I wouldn’t have known how to do the fill and line. Thank you!!!
@computercreationz
2 жыл бұрын
Glad I could help!
@RoderickMcFarland
2 жыл бұрын
@@computercreationz Ok why am I not seeing the fill + line option? I only see line / fill / offset fill in my drop down menu
@computercreationz
2 жыл бұрын
@@RoderickMcFarland they have added sub layers so you set you layer to fill then click the little +in the top right hand side add a sub layer and add line. Many more options this way. It all covered in the lightburn documents
@RoderickMcFarland
2 жыл бұрын
@@computercreationz Thank You 😊 I'm going to experiment with the new sub-layers today 👍🏿😁
@mojowbm
3 жыл бұрын
Thanks, Robert! Your videos are always so helpful. Appreciate you! :)
@computercreationz
3 жыл бұрын
You are so welcome
@barryfriesen8062
3 жыл бұрын
As always, learned something that I will try when I get back to the shop! Thank you.
@computercreationz
3 жыл бұрын
Have fun!
@davegirimonte9945
2 жыл бұрын
I need some help in different situations watching your videos help me out a lot thank you so much
@computercreationz
2 жыл бұрын
thank you for your comments, glad these vids are helpful!
@RuffKutmedia
3 жыл бұрын
Good video, thanks for sharing I love leering about the fine tweaks I can make to my Projects that make them look so much better. Keep up the great work!
@computercreationz
3 жыл бұрын
Thanks for the comments, I appreciate you watching
@PhivosUT
3 жыл бұрын
Thank you. I always learn something from your videos. 👍
@computercreationz
3 жыл бұрын
My pleasure!
@muhammettahasari1701
2 жыл бұрын
thanks brother. I hope everything is good. thats usefull videos.
@computercreationz
2 жыл бұрын
I appreciate the comments
@samvoelkel2046
3 жыл бұрын
Thanks for the information. I will try using the "fill + line" option soon.
@computercreationz
3 жыл бұрын
Glad it was helpful!
@wildwestcreations268
3 жыл бұрын
I always appreciate your teachings. Thank You
@computercreationz
3 жыл бұрын
I appreciate your comment.
@johngurney7087
3 жыл бұрын
Thank you, Love you videos. Stay safe from Aus.
@computercreationz
3 жыл бұрын
Thank you! Will do!
@lnman64
3 жыл бұрын
Another great and informative video. Thank you
@computercreationz
3 жыл бұрын
I appreciate it James
@lushlemonco
Жыл бұрын
great video! thank you!
@computercreationz
Жыл бұрын
Glad you liked it!
@campisij
3 жыл бұрын
thxs once again. the #1 reference.
@paulfitzgerald8795
2 жыл бұрын
As always, another great video. I see air assist mentioned in the comments and was wondering if you have a video on this. It would be nice to know when to turn it on, when to keep it off and how the different PSI affects your laser results.
@computercreationz
2 жыл бұрын
the rule I follow is when engraving you want as little air as possible and still keep your focus lens clean.
@jimmccall4599
3 жыл бұрын
great video as always sir, can hardly wait to try this technic
@computercreationz
3 жыл бұрын
Hope you enjoy it!
@josephlail5013
Жыл бұрын
Great video 😁 I will try this next!
@computercreationz
Жыл бұрын
Hope you enjoy
@jankristensen7884
2 жыл бұрын
super tip, i will try it
@computercreationz
2 жыл бұрын
thanks for the comment! give it a try it works great!
@B3RG3RS0N
9 ай бұрын
Great. Thenk You
@computercreationz
9 ай бұрын
Welcome 👍
@albertdrew7235
Жыл бұрын
Great video, however I do not have the option "fill/line" using version 1.3.01 of Lightburn..Unless option somewhere else. Thanks
@computercreationz
Жыл бұрын
Yes it’s there you will notice that there is a little plus sign to the right now you can add as many tabs that do different thing on one layer it’s a great new feature. Lots of KZitem on hot to use the new feature
@samterian7694
3 жыл бұрын
you are the best channel on KZitem, for me. is this software compatible to Mach3?
@computercreationz
3 жыл бұрын
I don’t believe so,
@gasphotography
4 ай бұрын
Great video. Question for you? I see that you have no additional charring or residue around your letters. How have you avoided that without taping; did you alter the overscan settings?
@computercreationz
4 ай бұрын
It’s all About the lack Lack Of air flow. I use just a whisper of air when I engrave anything. That way the vaporized material doesn’t get pushed back on the piece. Very little post prep is needed.
@hhallman7380
3 жыл бұрын
Another informative video. Thank you and keep up the good work. Can you do a video on the Print & Cut feature using pass-thru with 2 cuts (1 alignment) and 3 cuts (2 alignments)?
@susankeenan7084
3 жыл бұрын
Thank you for another great video.
@computercreationz
3 жыл бұрын
Great suggestion!
@stevenschellin4631
3 жыл бұрын
Great Video, this is very helpful.
@computercreationz
3 жыл бұрын
Glad to hear it!
@kathykat1838
3 жыл бұрын
Thank you, this was helpful.
@computercreationz
3 жыл бұрын
You're welcome! and thanks for watching
@omfd100
2 жыл бұрын
Your brilliant
@computercreationz
2 жыл бұрын
thank you for your comment!
@amandaford1471
2 жыл бұрын
I am very happy my husband sent me your channel! I have a 20 watt ortur laser, I use lightburn. Should I increase my settings since you have a 60 watt?
@computercreationz
2 жыл бұрын
yes because your laser is a diode laser and mine is a co2 laser the settings will be substantially different. Thank you for watching!
@ruizd14
2 жыл бұрын
I been meaning to check out that fill + line mode in lightburn. What I recently did, and it came out really cool was I first did a fill operation of some text then on a second operation did the line mode on that same text and it came out spectacular but that does requires doing it in two operations. I assume the fill + line is done as part of the same operation? I do plan to test that mode soon. Thanks. man. I always like stopping by 🙂
@computercreationz
2 жыл бұрын
I appreciate your comments, thanks for stopping buy!
@derrickstewart5554
3 жыл бұрын
Great Video. Always informative. If I may offer a request. Can you guide me on how to do a picture on acrylic. I am really struggling with this.
@computercreationz
3 жыл бұрын
Great suggestion!
@IaidokaNC
2 жыл бұрын
did they remove this option? I tried to follow along but it doesn't seem to exist anymore in the current version?
@TheGuitarman1968
2 жыл бұрын
@Casey Pettus See my previous post. I am wondering the same thing, as I use this setting a lot, and now it has mysteriously disappeared since the latest Lightburn update. 🤔
@IaidokaNC
2 жыл бұрын
@@TheGuitarman1968 So what I ended up finding when hunting for this setting, was the ability to add "sub layers", so I set one up as the line with my normal settings, then another layer as fill with my fill settings. I assume this is replacing the Fill+Line option, and letting us add as many sublayers and options as we need. Can't wait to test it but it's a few jobs back in the que right now.
@TheGuitarman1968
2 жыл бұрын
@@IaidokaNC I tested this today. As you suggested, I am getting around the issue by duplicating text and creating two separate layers. One layer for "fill" and the other layer for "line." Then just overlay the line layer over the fill layer. This "work-around" requires a few extra steps, but it works great so far. 👍
@computercreationz
2 жыл бұрын
as you’ve seen below they just have a different way of approaching it now. works great!
@TheGuitarman1968
2 жыл бұрын
FYI.....I updated the to the latest Lightburn software on my desktop and laptop computers today (6/30/22). The "Fill+Line" setting is now missing from the drop down menu. Does anyone know if this was done accidentally or intentionally by Lightburn? This really sucks, as I used this setting a lot in order to make letters and numbers stand out on signs. 🤔
@computercreationz
2 жыл бұрын
it’s there, it’s handled in a sub layer instead. sub layers are brand new. so you would have a fill layer then add a sub layer for the line.
@TheGuitarman1968
2 жыл бұрын
@@computercreationz Yes, I did just that today, and it works great. I am getting around the issue by duplicating text and creating two separate layers. One layer for "fill" and the other layer for "line." Then just overlay the line layer over the fill layer. This "work-around" requires a few extra steps, but it works well so far. 👍
@computercreationz
2 жыл бұрын
@@TheGuitarman1968 no reason to do that go into the layer you want to fill hit the little + sign in the upper right hand corner and it will add a tab. Use line for your second sub layer. One design, one layer color two actions
@TheGuitarman1968
2 жыл бұрын
@@computercreationz Thanks for the info. I watched Rich's (The LA Hobby Guy) tutorial on this sub layer feature, in the latest update, that he made today. It is actually really cool to be able to do multiple actions in one layer. 👍
@teachererica5936
3 жыл бұрын
When you are doing engraves like this, air assist low? Wide nozzle? in focus or out of focus? :) Great video as always!
@computercreationz
3 жыл бұрын
Very low air, in focus. Standard nosle. Thanks for the comment and watching. Have a great day!
@Hillbillyable1
Жыл бұрын
You talk about the fill+line like it's just there on everyone's page. Maybe tell how to turn something on if your tutorial hinges on that right from the start.
@computercreationz
Жыл бұрын
When this video was made it truly was a selection in the mode section. Since then they’ve modified lightburn. Now you have to hit the plus button and add the tab for line or fill it’s very easy to do. Software evolves!
@sevenwindsflutes
2 жыл бұрын
I'm using Lightburn 1.2.01 In the settings I do not see a line+fill option. I only have Line, Fill, Offset fill. Is this because I am using the Atomstack A20 diode machine? What am I doing wrong? Thank you for the great videos.
@computercreationz
2 жыл бұрын
Lightburn has adopted sub layers so now you start with fill then add line as a sub layer with the little + to the right. Lots more flexibility. KZitem lightburn sub layers are you’ll see how it works. Different but much more powerful
@sevenwindsflutes
2 жыл бұрын
@@computercreationz Thank you very Much! This is brilliant.
@komchand9313
3 жыл бұрын
Hi I trying to do cut and engraved on 4mm plywood was not able to cut I used lightburn software and atomstack a5 pro need your help for setting
@fluiditynz
Жыл бұрын
1.4.01 doesn't have fill + line setting in drop-down optiions.
@computercreationz
Жыл бұрын
It does they just reconfigured the layer layout . Look to the far right top section of your layer and you will see a + sign and you can add a sub layer. Your first will be fill your second will be line! Same function
@fluiditynz
Жыл бұрын
@@computercreationz I found discussion of the change minutes after commenting and tried it last night. Works well!
@heatherjones74
3 жыл бұрын
Is this only for text? Or can I use this with designs as well?
@computercreationz
3 жыл бұрын
No, I use it for all kinds of designs. I used text in the video because it illustrated the effect better. Try it out it’s an awesome effect.
@f0xvibes
Жыл бұрын
unfortunate i dont have this option in Lightburn 1.2.04...
@computercreationz
Жыл бұрын
You do you access it differently. Look for the plus symbol on the right hand side. The first tab should be fill then add a tab and switch mode to line. This t remove it they enhanced it so you can have up to 11 tabs. It’s a great new feature
@f0xvibes
Жыл бұрын
@@computercreationz thanks for sharing this with me. It's awesome, now we can make several layers with different filling patterns
@thatsawrapcustomgifts
Жыл бұрын
How did you get the fill + line? I do not have that option.
@computercreationz
Жыл бұрын
They modified it and max it it better look on the top right hand side of the layer when opened and click on plus sign. It adds a tab that you can add line. You can do up to 11 options in a single layer now
@janenguyen7572
3 жыл бұрын
Once you finish engraving on your wood do you normally have to clean it? My one always comes out with a smoky look. Not sure if it is because my air is on too high😖. What setting do you have for your air?
@computercreationz
3 жыл бұрын
too much air when engraving can cause lots of smoke damage. I turn down my air flow to just a whisper when engraving. thanks for watching!
@lpaltageek
3 жыл бұрын
I am new to laser cutting, I have optimization settings to cut inner shapes first but it cuts outside line first?
@computercreationz
3 жыл бұрын
make sure your layers are stacked in the sequence you want cut. top is first and so on
@kevinr2737
2 жыл бұрын
Good trick, but lots of redundancy on the explanation.
Пікірлер: 98