IF YOURS HAS BURRS ON IT LIKE THIS, You Must lap it to remove them or else they could potentially cause harm to your scope tube. I really hope this was just a fluke with this one particular mount. But be Warne-d. Did ya see what I did there?
@Gabthar
11 ай бұрын
No. I’m retarded
@williamnantz5604
10 ай бұрын
I was thinking the same thing, that the rings could be lapped. But at $270, it's totally unacceptable that you should have to. Good review.
@madhatter6913
11 ай бұрын
1000+ reasons why I watch your channel.
@surviveautodafe
11 ай бұрын
yeeeaaah I'll stick with my ADM.
@discipleofjmb
11 ай бұрын
Excellent and fair review. Thanks for evaluating the things typical guntubers would miss or at worst, cover up.
@L330ne
11 ай бұрын
Here I was listening to the Smiths and being in the market for most of your videos.. I must pause and watch.
@ShersGarage
11 ай бұрын
I used Leupold Mark AR mounts on my rifles. They held up well. Around $89. Made in USA!
@alexxu3004
11 ай бұрын
we tend to forget we had to lap scope rings mere two decades ago and get spoiled by relatively inexpensive and decent cnc rings from china
@GldenRetriever
11 ай бұрын
I think you'll be thoroughly impressed with the monstrum pro (7075) cantilever mounts. i like it more then my UTG and basically the same price.
@twogenders
11 ай бұрын
My experience with Warne mounts is worse than yours. I had a Warne 1.9" MSR mount for a long time. It was excellent. Then I bought 3x more from Warne, and they were terrible. The workmanship and quality were subpar compared with the older one I had. The screws would not go in properly. Even though they had the same exact model #. I returned them.
@dnaka2001
11 ай бұрын
That sucks. I considered getting this mount. I'm glad I didn't. I used a few of the Warner X-Skel mounts. I have had the ring on those leave marks on a scope tube where the ring segments meet. This was at 15-17 inch pounds. I use kapton tape as a liner with them now.
@yzwme586
11 ай бұрын
I would love to see a video on the Badger Ordnance COMM
@deathtothewageslave
11 ай бұрын
You need a low end test scope, those scratches look brutal.
@Bender_B._Rodriguez
11 ай бұрын
If its one thing that bugs me is the caps dont close up very close to each other, I got some pri rings for my 16" setup. I have them on a swan sleeve made by pri and I love the setup, I dont like that PRI aluminum and steel ringe are the same dimensions so I can turn a top cap into an MRDS mount. I have to use a separate ring so at some point I will have to change my pri rings our for something else.
@FlowBaka
11 ай бұрын
So you being a machinist explains why you have a titans of cnc shirt.
@chipsterb4946
11 ай бұрын
Argh! And Warne insisted *not* to lap their scope mount when I called to ask…
@e7tegt503
11 ай бұрын
I’d call em and ask them to send you a new one. Excellent insights.
@jeffburgert8929
6 ай бұрын
Always lap the rings before mounting.
@seymour2113
11 ай бұрын
Hey cdoos I have a Promethean LP-1 I can send in for you to review, not sure how to contact you
@gusatl2068
11 ай бұрын
I can’t believe you damage your scope finish.. Dang
@InfernoPhilM
11 ай бұрын
$270 is steep for that mount without innovations
@sdvten
9 ай бұрын
I got my first and last Warne MSR mount recently. The flash from the (what looks like) MIM bottom was horrible and made the mount unuseable until flash was removed as it would damage the scope tube considerably. On top of that two screws came cross threaded and damaged from the factory. Try to buy American but the mount I got is horrid. The Aero Precision mounts I have are by far superior in quality for much less money.
@CDOES
9 ай бұрын
I'm glad I wasn't the only one. But I'm sorry to hear about your experience.
@sdvten
9 ай бұрын
@@CDOES Their customer service seems good at least. I got new screws less than a week after contacting them.
@joearledge1
3 ай бұрын
Aero mounts bend like a coat hanger... I like aero, but their mounts suck. It's the same problem a lot of the mounts have, for some reason most manufacturers use bubble gum soft 6061.
@vincebalsamo2219
11 ай бұрын
I would never give this fund any money due to the fact that the ATF is controlling it. Btw I’ve never seen a public firing range. 😂
@BBouncer
3 ай бұрын
This is why you need to lap any rings or mount...I've found issues in both expensive and cheap examples.
Пікірлер: 28